STM32 MCUs Products

Hello,I’m currently testing the CSI–DCMIPP interface on the Nucleo-N6 board. I’m following various examples, but the variable used in DCMIPP_Start (lcd_bg_buffer) is not receiving any data. Is there something I might have configured incorrectly?At the moment, the buffer is configured to be stored in ARAM2.

Hi,I’m working with the STM32F407VGTX and I am using GPIO PA4 as the SPI chip-select (CS) pin. In my GPIO initialization, I set the PUPDR register to configure PA4 with a pull-up, expecting the CS pin to remain HIGH when idle. However, I observe on my logic analyzer that after initialization PA4 goes HIGH briefly, then returns LOW (its default state) even though the pull-up is set. I am attaching a screenshot of my logic analyzer for reference.Could anyone please explain why the pin doesn’t remain high with the pull-up configuration, and what’s the correct way to configure PA4 so that CS is HIGH when SPI is not active?Thank you! 

I turned off all the other configuration aka Alternate Functions..only enabled GPIO PA5 as output Pushpull mode, low freq.its doesnt turn on or off individually..tried to turn on and off using HAL as well as direct registers..both work only when PA4 turns on ...what i mean if i want to turn on PA5 i should turn on PA4, then only it works..what is this causing this issue.can you help me out.tried on multiple hardwares..same issue so hardware issue eliminated, no pin short circuit. 

Hi, I bought 50pcs STM32L151C8T6A from one Chinese online vendor, which has device marking with QR code.I encountered an issue while using the new version chip, after initial power-on, the overall sleep current of the product is approximately 5uA(STM32L151C8T6A in stop mode), When I reset the product's hardware multiple times, there is a high probability that the product's sleep current will reach up to 1.6mA. Once this occurs, the product can only return to normal by being powered on again.With the same hardware, replacing the STM32L151C8T6A with an older version will prevent the issue from occurring.This is a mature product, and this is also my first time using the new version of STM32L151C8T6A. Is the software for the old and new versions incompatible? What should I be aware of?ps: I am using the STM32L series standard library.       

Hi,I'm trying to implement an external loader for the Arduino Giga R1 board with AT25S128A 128Mbit of external flash. After following the guide given in the external loader repo, I'm running into the problem, that I can erase, write & read from the memory fine, however, as soon as I try to turn on memory mapped mode, all the data reads as 0xFF...FF, both in code and in the STM32CubeIDE memory viewer. I think my problems could be related to MCU configuration, I would be grateful if someone could give some guidance, see the relevant code below and attached. quadspi.c:uint8_t CSP_QSPI_EnableMemoryMappedMode(void) { QSPI_CommandTypeDef sCommand = { 0 }; QSPI_MemoryMappedTypeDef sMemMappedCfg = { 0 }; // Enable Memory-Mapped mode sCommand.InstructionMode = QSPI_INSTRUCTION_1_LINE; sCommand.Instruction = QUAD_INOUT_FAST_READ_CMD; sCommand.SIOOMode = QSPI_SIOO_INST_EVERY_CMD; sCommand.AddressMode = QSPI_ADDRESS_4_LINES; sCommand.AddressSize = QSPI_ADDRESS_24_BITS; sCommand.

I'm in the middle of attempting to reconfigure the clock tree on my STM32F303K8. The old clock tree looks likeThe new clock tree looks like The old clock tree works fine. The new clock tree always fails on boot; not always in the same address but always in the neighbourhood of HAL_RCC_ClockConfig. An example stack trace looks likeIn this case it claims to have failed on this line 769 of HAL_RCC_ClockConfig: /* Get Start Tick */ tickstart = HAL_GetTick();This is failing in the MX-generated code well before any of my own code runs. The goal is to keep the CPU clock at 64 MHz but reduce everything after the AHB prescaler. The diff of the RCC section in the .ioc file looks like this:     

Hi Team,I have few questions regarding stm32h7 errata.Errata 2.2.21, Can silicon revision 'V' support a cpu frequency of 480 Mhz ? If yes, why is it showing 'P' for v revision.    2. Can I please ask if there is a fix in the HAL for the below given SPI errata  (from 2.22.2 to 2.22.6)? Regards,Alex 

I'm bringing up a design based off the STM32H573 and I believe I'm having a number of issues that are probably sharing a common thread with bad hardware. I don't usually screw those things up, but I guess I got unlucky this time.1) PC1 when configured as a (GPIO) output cannot drive a load. Works as a GPIO input. Sometimes, when configured as output after configuring it as input, it would start working and then die (this happened twice in two days). Pulls, OD, nothing seems to make a difference. Replicated over two boards -- the second board with no ESD damage possible. 2) HSI seems to be off by 9% (HAL_Delay and UART are showing this error). Tested on one board only. Here is my schematics:In my actual board, both VCAPs are not tied together. They are also not placed on the bottom of the board -- rather they are connected via a 0.1mm trace 3.5mm long to the edge of the BGA to the capacitor. Altium is saying this can carry 0.6A I guess impedance is bad and it might be the

HI USB-C Input (5–20 V PD) + USB-C Data (USB2.0 D+/D– to STM32H745) + charging phone at same time + Audio data transfer Problem: When I connect the USB-C input supply (PD 5–20 V), the phone only charges and the audio USB port does NOT appear.But when I do NOT provide PD input power, the audio USB port appears correctly.And if the audio port is already active, then when I connect the PD input afterwards, the phone does NOT charge — only the audio stays active    

Hello everyone,This is my first post on the platform, so please bear with me.I would like to write raw data to an SD card very quickly.After quite a bit of research, I decided to use SDMMC with MDMA, and I want to write directly to the SD card blocks to avoid latency associated with the FATFS overlay.Apart from an old post that explains how to configure MDMA and link it to SDMMC, I haven't found any concrete examples of a function that allows reading and writing to the SD card.Could you give me a simple example of writing and reading to use MDMA with SDMMC to write to the SD card, or point me to existing projects or examples that I may have missed?Thanks in advance. 

I'm trying to port a proprietary code that is designed for another STM32H753 plateform, to a STM32H753-EVAL board.My code remains stuck waiting for HSERDY bit.The setup I am doing looks identical to STM32CubeHW example but I guess I forgot something: - set LDOEN in PWR_CR3 register and wait for ACTVOSRDY- set voltage scaling to VOS1 (bits 14 and 15 in PWR_D3CR register) and wait for VOSRDY- set bit HSEON and wait for HSERDY -> bit is never set I setup the eval board JP10 to be powered up through the jack (external power supply) If I power the board through STLink, I have no issue. Am I missing anything ?

I want to use N657B0 to drive VD55G0, and the camera side can already enter the Stream state. After I use the function HAL_DCMIPP_CSI_PIPE_Start, I track the variable csi_instance through single-step debugging and find that several bits in its SR1 register are inconsistent with the normal state. And I find the defination about these.The normal state is 1 but I get 0.Could you please tell me what the reason for this might be? Is the issue caused by a voltage supply problem in the hardware connection, or by inadequate rate matching in the port?

I have a STM32U595 and I use the RTC in binary mode.If an SSR underflow occurs during Vbat mode, will the SSRUF be set so after power recovery I can manage the interrupt ?

From my understanding all STM32N6 chips need a external flash chip and there's a static stage 0 boot loader.  So if this is true is there any limitation's on the brands of flash or speed/address bit size limitations? With the previous stage 0 bootloader for a different non ST product had a lot of limitation on the flash that could be used.* 16 bit flash address only* Only support a few brands of flash chips.  

Hi Everyone,I am working on a project with TouchGFX. I'm working with STM32U5G9ZJT6 and I have an external RAM APS12808L-OBM-BA connected via HSPI (Fclk-hspi 100 MHz) in mapped mode. The project is working, but the image animation are not working well. To solve it I have decided to increase the HSPI frecuency.The APS12808L-OBM-BA memory can operate at up to 200MHz. However, when I exceed 118MHz, I can't map the memory. You can see a picture below reading the memory after mapping (you see "?").I have changed the memory read latency (MR0 and MR4) to increase the Fmax.I need all of suggestions for this issue.Thanks in advance all     

In the RM0456 at 33.4.31 Oversampler it say:The division coefficient M consists of a right bit shift up to 10 bits, and is defined using the OVSS[3:0] bits in the ADC_CFGR2 register.But at 33.6.5 ADC configuration register 2 (ADC_CFGR2), it allow up to 11 bits:Bits 8:5 OVSS[3:0]: Oversampling right shift1011: 11-bit right shift

Can somebody please help me.   The code below is initializing the RTC.   The clock works I can set and read time and date no problem.   Somehow if I change these register:   hrtc.Init.AsynchPrediv = 131; hrtc.Init.SynchPrediv = 10;   It has no impact on the clock accuracy I keep on gaining time.   I would have thought by "tweaking" the values it will either speed up or slow down the RTC.    Code was generated by using the STM32 cube IDE.     /** Initialize RTC */ hrtc.Instance = RTC; hrtc.Init.HourFormat = RTC_HOURFORMAT_24; hrtc.Init.AsynchPrediv = 131; hrtc.Init.SynchPrediv = 10; hrtc.Init.OutPut = RTC_OUTPUT_DISABLE; hrtc.Init.OutPutPolarity = RTC_OUTPUT_POLARITY_HIGH; hrtc.Init.OutPutType = RTC_OUTPUT_TYPE_OPENDRAIN; if (HAL_RTC_Init(&hrtc) != HAL_OK) { Error_Handler(); } /* USER CODE BEGIN Check_RTC_BKUP */ /* USER CODE END Check_RTC_BKUP */ /** Initialize RTC and set the Time and Date */ sTime.Hours =

We're using the following circuit to measure a battery voltage @ 20 kHz for use in motor control.We are having some issues though, where the ADC suddenly starts measuring 0 V (0 in the data register) and gets locked in this state. In this state, we also measured 0 V at the MCU pin on the board, and a resistance < 20 Ohm between the pin and GND, both using a multimeter. The issue is not fixed by a reset (pulse on the NRST pin), only removing the battery and power cycling the MCU.How and why can/does this happen?We initially thought it was overvoltage and tried connecting a PSU directly to an ADC pin on the STM32G474RE NUCLEO board. We only started seeing abnormalities at 6 V and destroyed the ADC at around 9 V, so this does not seem to be the reason.The ADC is clocked 170/4 = 42.5 MHz and configured as follows (from IOC file):ADC1.CommonPathInternal=null|null|null|null ADC1.DMAContinuousRequests=DISABLE ADC1.EOCSelection=ADC_EOC_SEQ_CONV ADC1.EnableAnalogWatchDog1=false ADC

Hi,I'm attempting to write to an SD Card using a Riverdi STM32U5A9 display board.  Since TouchGFX natively uses FreeRTOS, I'm attempting to keep it within FreeRTOS.  Porting to ThreadX has caused it's own issues which I have in a separate thread.  In the Configurator, there is no longer an option for FATFS, so I'm using the STM32U5 Classic MW Git Repository as recommended by the FAE.  I copy over and update the templates as required, but am still getting a Hard Fault during f_mkfs while the HAL library is initializing the SDMMC.  I believe that my configuration is incorrect, but the example is only for SDRAM, so I'm not entirely sure where I've gone wrong...  I have it setup for 4-bit width and I've changed the clocks to be 24MHz at the SDMMC clock output.  The examples within the configuration are for older MCUs and have a tab to enable the DMA.  My understanding is that the STM32U5 has an Internal DMA, so it's not required to setup the DMA with

Hi, I am trying to configure my STM32G071GBU6 to enable reprogramming  the flash throguh USART1. I check the datasheet of STM32G071x8/xB, reference manual RM0444, and application note AN2026. It says I am supposed to configure the PA9 (USART1_Tx) and PA10 (USART1_Rx) pins. The problem is when I configure the USART1 as asynchronous mode in STM32CubeMX, the software automatically set PB6 and PB7 pins as USART1_Tx and USART1_Rx. There are no available options like USART1_Tx and USART1_Rx for PA9 and PA10.I am wondering why the manual is inconsistent to the STM32CubeMX and how should I configure the MCU to correctly reprogram through USART1?

Hello everyone, Some time ago I asked on this website information about jitter on a PWM : Solved: PWM jitter - STMicroelectronics CommunityThe problem was that when generating a PWM, it wasn't very stable. At the time changing the source clock to the external clock of the nucleoboard worked and stabilized everything.Since then, I created my own board using an STM32G474QE (128 pins) with an 8MHz (+/-50ppm) external oscillator.I tried to generate the PWM and I am encountering the same exact problem again, the jitter is back. This time, I directly setup the clock as the external one. I checked it up and it feels to me that the problem could be coming from the stability of my oscillator (I have frequency variation on it's output ranging from 7,999,950 to 8,000,050Hz). Now my question is, could this really be the problem and could a lower ppm oscillator work ?I tried looking up information on my own especially using AN2867 but I only get information about crystal os

Hello everyone i had today while working with the NUCLEO H753ZI board and when i try to upload the code i had faced this error message when i try to connect with the cube programmer i faced this error and my LD6 pin is glowing with low intensity can you please tell me why i facing this issue whethere this could be any short problem or anything else 

I have two boards, both with the G473.I am using the ROM bootloader on SPI1. On one board, the bootloader works.  On the other, it only responds with 0xA5 during the initialization sequence.The MCU can program and run if I load it through the SWD port.I have checked the SPI signals, both digital and analog, they look great.  The MCU pins are firmly soldered to the board.  The other board works.  My code works.  If you can actually get the bootloader to synchronize, it works.I have gone through every forum post I can find, and it is sounding like there is a possible consensus that the ST bootloader is bugged and will sometimes initialize the wrong interface.  Is that... really true?  It selects the wrong interface and all of these people are having problems with it?  Can any one from ST talk about this?  This sounds like a really serious problem if true!  What else could it be?AN2606 says the G473 will init the pins on the USART and

Hello, I am facing an issue with my code on my STM32F411I have a function that is starting a timer TIM5 I want to be able to handle channel 1, Channel 2, Channel 3 interrupt on output compare no output uint32_t ticks = ms * 10U; /* 10 kHz tick -> 10 ticks per ms */ if (ticks == 0) ticks = 1; TIM5->CR1 = 0; TIM5->CR2 = 0; TIM5->DIER = 0; TIM5->CCER = 0; TIM5->CCMR2 = 0; // Channel 3 and 4 CCMR register // Set prescaler and auto-reload as needed TIM5->PSC = 96; // No prescaler TIM5->ARR = 0xFFFF; // Auto-reload max for full range TIM5->CCMR2 &= ~TIM_CCMR2_CC3S; // CC3S=00 output TIM5->CCMR2 &= ~TIM_CCMR2_OC3M; // Clear OC3M bits TIM5->CCMR2 |= (0x3 << TIM_CCMR2_OC3M_Pos); // OC3M=011 toggle mode // Enable Capture/Compare Channel 3 output (optional for toggling output pins) TIM5->CCER |= TIM_CCER_CC3E; // Enable interrupt on Capture/Compare 3 event TIM5->DIER |= TIM_DIER_CC3IE; // Enable TIM5 counter //TIM5->CR1

Hello ST Community,I am working on an STM32U585AII6Q microcontroller with TrustZone enabled. My goal is to revert the RDP level from 2 (0xCC) back to 0 (0xAA) using STM32CubeProgrammer GUI.#### Steps I Followed:1. Defined OEM2KEY in the "Secure Programming" menu.2. Set RDP to Level 2 successfully.3. Tried to unlock RDP2 using the "Unlock RDP2" option in STM32CubeProgrammer.- Log shows: "Unlock RDP2 password successfully done."4. Gave power cycle and attempted to change RDP value from 0xCC to 0xAA in the "Read Out Protection" menu.#### Issue:- When I try to apply the change, I get the error:**DEVICE NOT HALTED**- The debugger cannot connect to the MCU after this step.#### Hardware Setup:- BOOT0 pin connected to VDD for RSS boot.- Using STM32CubeProgrammer v2.19.0.#### Questions:1. What is the correct sequence to regress from RDP Level 2 to Level 0 when TrustZone is active?2. How to resolve the "DEVICE NOT HALTED" error during regression?3. Do I need to power-cycle or use a specific mode