MEMS (sensors)

Hi, I look on different application notes linked to the LPS27HHTW but I found nothing about its failure mode.I want to know what could be its failure mode and how will it react for eg on SPI communication (value at 0 or minimum or sea level pressure?) Thanks for your help     

Hello,we're considering to use ASM330LHB in the SIL2 functional safety application and we would like to use and take credit from ST's ASILB-LIBRARY. However ASILB-LIBRARY use-case as it's documented expects that two redundant senors will be employed. Can be ASILB-LIBRARY used only with single IMU source? Thank you for the answer and support@Denise SANFILIPPO thank you for your awesome article on this topic https://community.st.com/t5/mems-and-sensors/how-to-augment-your-automotive-safety-applications-with-the-imu/ta-p/670346 

Posted on September 08, 2015 at 14:18Dear All,I am writing a firmware that is supposed to detect if a body is moved for a certain time i.e. 3 seconds of continuous motion. I am using LIS3DH Accelerometer sensor. Here is the configuration registers values:CTRL_REG1 = 0x2F          //Enable all axes + ODR = 10 HzCTRL_REG2 = 0x00          //DefaultCTRL_REG3 = 0x40          //Enable AO1 interrupt on INT1CTRL_REG4 = 0xB0          //16G full scaleCTRL_REG5  = 0x00          //DefaultCTRL_REG6 = 0x00          //DefaultINT1_CFG = 0x7F         //6D movement recognetionINT1_THS = 0x02         //Note FS = 16G. (Sensitivity = 0.25G)INT1_DURATION = 0x1E         //0x1E =

Hello, I have as project to use the STWINKT1B board and write my custom code to read IMP23ABSU sensor at its maximum capacity (80kHz). I understand the sensor output data is amplified by an op-amp and can be read with ADC input of the microcontroller, but what is the exact interface ? I don't really understand the schematics logic of the sensor (Why is there 2 ouputs: "MREF" and "M1P_FILT", why are 2 op-amps used)Could you please give me more details ?Then, is there some basic examples of how to read the sensor ? ADC input configuration, sensor configuration, reading...Thank you

Hi! In the Linux, I want to use buffer mode with st_lsm6dsx driver.But there isn't file /sys/bus/iio/devices/iio\:deviceX/buffer/enable. Why?The chip used is LSM330DLC, linux kernel version is 6.1.55 in nxp's yocto. ■log1(there isn't buffer directory)root@XXX:~# ls /sys/bus/iio/devices/iio\:device0/current_timestamp_clock in_anglvel_scale_available in_anglvel_y_raw name power sampling_frequency_available ueventin_anglvel_scale in_anglvel_x_raw in_anglvel_z_raw of_node sampling_frequency subsystem waiting_for_supplierroot@XXX:~# ls /sys/bus/iio/devices/iio\:device1/current_timestamp_clock in_accel_scale in_accel_y_raw name sampling_frequency ueventdev in_accel_scale_available in_accel_z_raw of_node sampling_frequency_available waiting_for_supplierevents in_accel_x_raw mount_matrix power subsystem■log2(latest value can be obtained)root@XXX:~# cat /sys/bus/iio/devices/iio\:dev

Hello,I am working on migrating from the LSM6DSO32 to the LSM6DSV32X for my application.  My primary interest in the newer part is the increased gyro range to 4000dps.  I am trying to keep the operation of the device similar to what I am using now.Some of the operating modes have changed and I have a couple of questions.The gyroscope no longer has a "Normal" mode.  Is "Low Power" mode the next best option to use?  If not, which is?The accelerometer no longer has "Ultra Low Power (ULP)" mode.  It appears the lowest power option available is LPM1.  Is this correct?  Also, throughout the datasheet, LPM1 is noted as "2 mean."  Can this be explained more?  Does this factor into the decision of what data rate I need to select (for example if I was using 12.5 Hz previously, would choosing 15 Hz yield the closest performance or would I have to choose double that to account for some sort of filtering?)

Hello everyone,I am currently developing an IMU array application using the ASM330LHHXG1 sensor and am trying to streamline my interrupt management. This sensor has two interrupt pins, and I am contemplating whether to use both pins or just one. My primary concern is with the Data Ready (DRDY) signal, which indicates when new data from both the accelerometer and gyroscope are available.Does anyone know if the DRDY signal from this sensor is synchronized for both accelerometer and gyroscope data? In other words, does one DRDY signal mean that both sets of data are ready to be read simultaneously? Additionally, I’m considering whether to assign each sensor type (gyroscope and accelerometer) to a separate interrupt pin or to use one pin for both.Could using two separate interrupts improve performance in any way, or would it be overkill for standard motion detection and tracking applications?Any insights or experiences shared would be greatly appreciated!

I recently bought the STEVAL-MKI245KA, consisting of an ad hoc PCB mounting the ISM330BX 6-axis IMU, which is connected through flat cable to a generic adapter board (STEVAL-MKIGI06A). I am trying to enable I2C commincation between the adapter board and an Arduino Mega, however, even after I connect the pins according to the datasheet of the components, when I run an I2C scanner on the Arduino, there are no devices detected. Here are my pin connections:  Adapter BoardArduino1VDD3.3V2GNDGND3SCLSCL4SDASDA5CS - VDDIO 6SDO3.3V

Hi All, We are using an Activity Monitor (LSM6DSOX) interfaced via I2C with the ATSAMD51J20A microcontroller. We have configured the device for single tap and double tap detection using the AN5272 configuration. We tested each configuration individually, and they are working fine. However, when we integrate both single and double tap detection, tapping the device twice triggers both the single tap and double tap interrupts. Could you please let us know if there's anything we missed in the configuration? Thanks and Regards GD  

I recently purchased the STEVAL-MKI109V3 motherboard and the STEVAL-MKI217V1 adapter board. After some setup, I managed to get the Uni GUI to work. However, I'm struggling to understand how to obtain real-time data from the system for further processing, such as calculating absolute orientation angles.My ultimate goal is to utilize the IMU sensor on the adapter board along with the sensor fusion software provided by the motherboard. I aim to integrate both components into a device I am designing, which will be powered by the nRF52840 microcontroller.I would greatly appreciate any guidance or resources that could help me achieve real-time data acquisition and leverage the full potential of the IMU sensor and sensor fusion software in my project.

I am looking to build a visual model of the human cochlea and was hoping to use the Adruino Nano 33 Sense which has a MP34DT06J microphone integrated.  I can't find the frequency range in the documentation, but I am not an electrical engineer--so maybe it's there, but I don't understand the units being displayed.  Ideally I would be able to pickup the full human hearing range (12hz to 28khz) so I can visualize this.  I am not as concerned about accuracy since I will only be mapping this to 160 leds in a spiral (the shape of the cochlea).    Thanks in advance for any assistance you can provide.

I tried to set up a project and to do the calibration of the sensor IIS2MDC on my B-U585I-IOT02A Board I want to use MotionMCNow the floating-point-ABI ist set to Hardware implementation and the Middleware used is the MotionMC Library MotionMC_CM33F_wc32_ot_hard.a But when I use the function MotionMC_Initialize(sampletime, enable) it ends up in an infinite loop. What solutions could I try to solve this?

What is Wraparound functions in LSM6DSO32? how to implement it?Do you have example code?I am using TI microcontroller TMS570LC4357

Hello, We are seeking a development board that has a compact IMU sensor (maximum dimension: 4mm) that includes an accelerometer, gyroscope, and magnetometer, along with firmware for embedded sensor fusion. Do you have any recommendations for us? We have used a variety of boards containing IMU sensors from different vendors, but we have not succeeded in obtaining stable yaw angle data without drift. If there is a board with a compact sensor that has all three sensing modalities and even an integrated sensor fusion firmware, that would be best I think.  Based on inputs from a ST support rep, I looked up STEVAL-MKI245KA evaluation board containing the 

Hello Everyone!!!I am using STM32F401CBU6 controller along with 2 sensors ie., (ISM330DLC & ISM303DAC) in my project. I have included motionfx library and getting Roll, Pitch, Yaw and Heading, but the heading is not getting calibrated and values are also changing continuously. i am using datalog fusion latest updated example code from X-cube mems1 with reference to UM2220.I have tried to to rotate the  sensor in all the possible directions to get it calibrate but it is not at all getting calibrated.Here is the data that i have logged, find the attached.@Petr S  or anyone please have a look and help me out!!!!regards,ANIL.

I want to use the L3GD20 gyroscope on my development board. But I didn't understand what I should do and I couldn't find an example on the internet. I know it communicates via SPI, but I could not send or read data. Can you please help me in detail?   

Hi ST support,We are using LSM6DSO32 accelerometer.I configured Single tap shock event on interrupt.Interrupt is getting generated when there is shock i want to read peak value of that shock. how to read acceleration data OUTX_H_A, OUTX_L_A, OUTY_H_A, OUTY_L_A, OUTZ_H_A and OUTZ_L_A when there is shock ?I want to read peak value of G when there is shock 

Hello Everyone!I am using ISM303DAC sensor in my project and facing an issue with Pitch value.  I have used MotionMC library and  calibrated the Magnetometer for heading. and also it got calibrated. As MotionEC_Run() function output consists of Euler angles i have printed those(roll, pitch) angles too...then i have observed one thing that if there a change in only roll axis then Pitch axis is not getting effected. but if pitch axis is changing then roll axis angles are also getting changed.                                 Movement only over Roll Axis ------ Pitch Angle is not changing and constant --->which is OK.                               Movement only over Pitch Axis------ Roll Angle is getting changed and it shot ---->Not OK as there is no a

Hi all,  Would it be possible to have an 8x8 array of capacitive pressure sensors connected to the Qvar pins by an analogue multiplexer.I would like the qvar to effectively scan across the sensing array. 

Hi, it seems there is a typo in AN5755 at page 8 ch.4.2 it says: "Moreover, Qvar data can be stored in FIFO (by setting the QVAR_BATCH_EN bit to 1 in the COUNTER_BDR_REG1 (0Bh) register)". This statement doesn't apply to LSM6DSV16X, because it is not possible to redirect QVAR data out to FIFO. It applies only to LSM6DSV16BX at ch4.3.regards

Hello everyone,I want to connect my pressure sensor (ilps28qsw) and have written the code in C and using I2C. If I use the example code as in the following link, and do nothing else, it works. For example, if I pull the variables (see below) out of this function and make them usable outside of the function (ilps28qsw_read_data_polling()) or want to execute other functions before or after this code, I get an error.I cannot understand this behavior. If anyone can explain it to me, I would be very grateful. Example code: https://github.com/STMicroelectronics/STMems_Standard_C_drivers/blob/m

I am currently working on a project involving the SensorTile.Box and am seeking assistance with utilizing its gyroscope and accelerometer sensors to determine location in the absence of GPS signals. Specifically, I am interested in processing the sensor data on a PC, similar to how data is managed in the ST BLE Sensor App on mobile devices.Could you please provide guidance on the following:Data Monitoring: How can I monitor sensor data from SensorTile.Box on a PC? Are there any recommended software tools or libraries for this purpose?Integration: How can I integrate and process gyroscope and accelerometer data to determine location? Any advice on using Kalman filters or other methods for this purpose would be greatly appreciated.Resources: Are there any additional resources or documentation you can recommend that could assist me in this endeavor?I am a student currently working on this project and would greatly appreciate any support or direction you

Hi,I'm evaluating the ISM330DHCX by connecting it on a board with a linux device (imx8) through I2C. (using the st_lsm6dsx - (compatible = "st,ism330dhcx") device.All of this seems to work out of the box, and I can read accelerations through IIO sysfs like so:  root@dev:/sys/bus/iio/devices/iio:device1# cat in_accel_x_raw 218 root@dev:/sys/bus/iio/devices/iio:device1# cat in_accel_x_raw 226 root@dev:/sys/bus/iio/devices/iio:device1# cat in_accel_x_raw 222 root@dev:/sys/bus/iio/devices/iio:device1# cat in_accel_x_raw 1105 root@dev:/sys/bus/iio/devices/iio:device1# cat in_accel_x_raw 210 root@dev:/sys/bus/iio/devices/iio:device1# cat in_accel_x_raw 220 root@dev:/sys/bus/iio/devices/iio:device1# cat in_accel_x_raw 226  These values also nicely change with the actual orientation. But, like in the snippet above, every once in

Hi allI'm working with an STM32F405 and one LSM6DSO32 and one LIS2DU12, eveyrthing works fine, but sometimes, for unknow reason, I go a strange whoamI from my captor, I got 0x20 value, I reset my mcu and it's works fine, any idea ? For my driver I use STM driver coming from stm github rep. Here is my i2c init function : I2C_HandleTypeDef hi2c1; void I2C1_Init(void){ hi2c1.Instance = I2C1; hi2c1.Init.ClockSpeed = 400000; hi2c1.Init.DutyCycle = I2C_DUTYCYCLE_2; hi2c1.Init.OwnAddress1 = 0; hi2c1.Init.AddressingMode = I2C_ADDRESSINGMODE_7BIT; hi2c1.Init.DualAddressMode = I2C_DUALADDRESS_DISABLE; hi2c1.Init.OwnAddress2 = 0; hi2c1.Init.GeneralCallMode = I2C_GENERALCALL_DISABLE; hi2c1.Init.NoStretchMode = I2C_NOSTRETCH_DISABLE; if (HAL_I2C_Init(&hi2c1) != HAL_OK) HANDLE_CRITICAL_ERROR(ERROR_INIT_I2C); }  

I am using LSM6DSOX for my project. As far as I understand, meta-classifiers need to be separate for each function (for my project). But I cannot separate two_hands_free and pushing_chart functions. I think this would pose a problem for machine learning. Is this really the case? Will this cause a problem? What should I do to separate these two? And also how is the meta-classifier determined? Should I collect more data to separate these two?