STM32 MPUs

Hi Team,There are two version of OSTL i.e. v4.0.0  STM32 MPU OpenSTLinux release note - v4.0.0 - stm32mpu-ecosystem-v4 and v4.1.0  STM32 MPU OpenSTLinux release note - v4.1.0 - stm32mpu-ecosystem-v4.  what is difference between them both are at 5.15.x kernel and using Kirkstone? Is OSTL v4.1.0/v4.1.1/v4.1.2 backward compatible with v4.0.0/v4.0.1/v4.0.2? @OlivierK  Thank you.

Hi:Recently, I have been transplanting Debian on the stm32mp2 platform, but Xfce cannot be started, and the following error keeps occurring. Can you give some suggestions? startx X.Org X Server 1.21.1.7 X Protocol Version 11, Revision 0 Current Operating System: Linux myd-ld25x 6.1.82 #1 SMP PREEMPT Mon Sep 9 07:52:16 UTC 2024 aarch64 Kernel command line: root=PARTUUID=e91c4e10-16e6-4c0e-bd0e-77becf4a3582 rootwait rw earlyprintk earlycon loglevel=8 console=ttySTM0,115200 xorg-server 2:21.1.7-3+deb12u8 (https://www.debian.org/support) Current version of pixman: 0.42.2 Before reporting problems, check http://wiki.x.org to make sure that you have the latest version. Markers: (--) probed, (**) from config file, (==) default setting, (++) from command line, (!!) notice, (II) informational, (WW) warning, (EE) error, (NI) not implemented, (??) unknown. (==) Log file: "/var/log/Xorg.0.log", Time: Sun Dec 1 14:13:50 2024 (==) Using system config directory "/usr/share/X11/xorg.conf.d" (EE

Hello,I am currently using Linux kernel version v5.15-stm32mp-r2.tar.gz and U-Boot version v2021.10-stm32mp-r2.tar.gz for my project based on the STM32MP family. I have recently upgraded the Linux kernel to linux-5.15-stm32mp-r2.2.However, I am unsure which U-Boot version is compatible with linux-5.15-stm32mp-r2.2. I tried using U-Boot version v2022.10-stm32mp-r2 with this kernel, but encountered the following error during compilation: Error: arch/arm/dts/.stm32mp157c-ccb-mx.dtb.pre.tmp:1478.1-6 Label or path sram not found FATAL ERROR: Syntax error parsing input tree Check /home/vivekb/workspace/source/NGACEM-269/SSB-buildroot/output/build/uboot-custom/arch/arm/dts/.stm32mp157c-ccb-mx.dtb.pre.tmp for errors make[4]: *** [scripts/Makefile.lib:336: arch/arm/dts/stm32mp157c-ccb-mx.dtb] Error 1 make[3]: *** [dts/Makefile:44: arch-dtbs] Error 2 make[2]: *** [Makefile:1173: dts/dt.dtb] Error 2 make[1]: *** [package/pkg-generic.mk:293: /home/vivekb/workspace/source/NGACEM-269/SSB-buildr

I'm encountering difficulties while attempting to connect and debug my STM32 microcontroller, and I'm seeking guidance from the community. I have erased the full chip flash memory and uploaded my code but suddenly I start getting these error messages,Error Messages:1. In ST-Link Utility:Can not connect to target!If you're trying to connect to an STM32W1xx device, please select Normal or HotPlug mode from Target->Settings menu.If you're trying to connect to a low-frequency application, please select a lower SWD Frequency mode from Target->Settings menu.

I want to know why I downloaded the latest JAVA, but I can't install STM32CubeProgrammer.*This post has been translated from Chinese to comply with the ST Community guidelines.

I'm using en.stm32cubemp2-v1-1-0.zip plus patch file en.stm32cubemp2-v1-1-1.zip I'm trying to build CM0PLUS_DEMO for STM32MP257x-EV1 for the cortex-M0 core.I got planty of errors when trying to build it with STM32CubeIDE Version: 1.17.0 Build: 23558_20241125_2245 (UTC):Failed to generate command line.reason: Unknown target. I'm reviewing the 'How to use the Cortex-M0+' document for any advise on how to build the example but it does not give any expecial advise so I assume I have to use CubeIDE:https://wiki.st.com/stm32mpu/wiki/How_to_use_the_Cortex-M0%2B#Memories_RIF_configuration_exampleOther examples for the Cortex-M33 build correctly. Thanks in advance, Hector.    

Hi,I try to use libpq library to connect postgresql from STM32MP157. It works on my computer. When I want to implement it to the board it doesn't work. I include path with .h but if I link libraries path I have that error.What I should do. Thanks in advance

Hi everyone,The stm32mp1 use SDMMC2 as default emmc controller. Now, I need use SDMMC1 to connect emmc flash. And I saw the OTP need changed. Bud I am confuse about IOs of SDMMC1. Does it also need setting some OTP bits to pinmux CK, CMD, D0?This picture show need change bit to chose SDMMC1.This picture is confused me. When I use SDMMC1, is it need configure CMD, CK,D0 to default pinmux on SDMMC1? If it is needed, where to configure those?

Hi Guys,Please I facing problem to have a QT application fitting the DSI screen,it sounds like it is 400x240 and not 800x480. I`m probably missing something on QTor on the STM32MP157C-DK2.Can someone please help-me to correct the resolution and how to use it landscape ?Thanks [ ]

Hey there,I'm trying to boot my custom stm32mp153c board using the new Scarthgap version of the meta-st-stm32mp layer. I had it working with the previous combination of optee 3.19 / kernel 6.1 (See this post). Ater some adaptation of device trees and my layer I've got OPTEE booting and loading the kernel, but unfortunately it stops right at the kernel loading. Any ideas what I might be missing or how to debug it further? Starting kernel ...D/TC:0 psci_cpu_on:172 core 1, ns_entry 0xc0301a40, state 0I/TC: Secondary CI/TC: Secondary CPU 1 switching to normal world bootD/TC:0 pwr_scv_handler:56 PWR service: write 0x0 at offset 0x28D/TC:0 pwr_scv_handler:56 PWR service: set 0x3f at offset 0x20I/TC: Reserved shared memory is disabledI/TC: Dynamic shared memory is enabledI/TC: Normal World virtualization support is disabledI/TC: Asynchronous notifications are disabledD/TC:1 0 stat_handle_fault:1740 nfaults 11264 npages 17 (min 16)D/TC:? 0 tee_ta_init_session_with_context:562 Re-open trus

I am trying stm32mp157f-dk2 for learning linux based on starter packageI just got succeed with load example 1 dtb and echo uart operating Anyway so I got checked the extlinux.conf file can control which dtb would be called But I dont know what's happening let me show what i wonder 1. Why stm32mp157c-dk2-extlinux.conf is called?2. Why load stm32mp157c-dk2.dtb? there's not FDT setting in default LABEL I can do with just change conf file in 157c-dk2 for nowBut i want to know how to select conf file Thank you

HelloI tried everything but I cannot get STM32CubeIDE to get the editor to work.I just keep on getting this message: There is no active editor that provides an outline.I spent hours re-installing but nothing workedAll help will be appreciated

Hello,I am trying to compile the Openst Linux for my custom board. I did it succeed in the Kirskstone distro which is based on tf-a. Now I try compiling the latest Openstlinux (6.0, scarthgap) with the optee-os but encounter a problem with the file generation. The problem I have is as followsWARNING: st-image-weston-1.0-r0 do_image_complete: Missing 'EULA_FILE_ST' var : no image license copied... WARNING: st-image-weston-1.0-r0 do_create_flashlayout_config: >>> Cannot generate FlashLayout_emmc_stm32mp157c-telemach-som-mx-opteemin.tsv file: the arm-trusted-firmware/tf-a-stm32mp157c-telemach-som-mx-opteemin-programmer-usb.stm32 binary for fsbl-boot partition is missing in deploy folder WARNING: st-image-weston-1.0-r0 do_create_flashlayout_config: >>> Cannot generate FlashLayout_sdcard_stm32mp157c-telemach-som-mx-opteemin.tsv file: the arm-trusted-firmware/tf-a-stm32mp157c-telemach-som-mx-opteemin-programmer-usb.stm32 binary for fsbl-boot partition is missing in deploy f

Hello, my aim is to achieve a reliable receiving UDP speed with stm32mp13 while sending a payload of 150 mbit/s.I did performance tests of 1 gigabit Ethernet using a MYD-YF13X development board and iperf3. Here are some of my results:19% packet drop rate at 150 mbit/s is, for my purpose, unacceptable. I think the problem is related to either the MPU or the YT8521SH Ethernet PHY.But I doubt it is the second one, so I would focus on the MPU itself. It seems to me that the MPU is not fast enough to achieve a sensible >100 mbit/s receiving speed.The architecture is arm 32bit, which has 32KB cache memory inclusive.The amount of cache is decisive for receiving huge payloads. Could it be the reason for such a performance? What was the reason to put 100 mbit PHYs and not 1 gbit into the STM32MP135F-DK? Best,J. Schneider 

Hi,I have STM32MP157f-DK2 . I built openstlinux-5.15-yocto-kirkstone-mp1-v22.07.27 , distro=openstlinux-eglfs , and I try flash image to sd card.When I am flashing "FlashLayout_sdcard_stm32mp157f-dk2-trusted.tsv" I have different errors related with partitioning ..., but when I am flashing "FlashLayout_sdcard_stm32mp157c-dk2-trusted.tsv", the board works....What can be wrong ? 

Hello,I am trying the open-st-linux-eglfs distribution with my QT application.When QT load my QML I am facing with this error :  module "QtQuick.Controls" is not installedHow can I verify the installation of qtquick control in my distribution ?

I've followed the READMEs for the installation of the dev package, source, and kernel and generated a build folder for the kernel as suggested at~/st/stm32mp2-openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06/sdk/Developer-Package/stm32mp2-openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06/sources/aarch64-ostl-linux/linux-stm32mp-6.6.48-stm32mp-r1-r0/buildIn the build folder I see folders include, scripts, a link to source as well as files Makefile, .config .config.old, and .gitignore. When I runmake ${IMAGE_KERNEL} vmlinux dtbs LOADADDR=0xC2000040 O="${OUTPUT_BUILD_DIR}"I getmake[1]: *** No rule to make target 'Image.gz'. Stop.make: *** [/home/lelory/st/stm32mp2-openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06/sdk/Developer-Package/stm32mp2-openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06/sources/aarch64-ostl-linux/linux-stm32mp-6.6.48-stm32mp-r1-r0/linux-6.6.48/Makefile:234: __sub-make] Error 2What am I doing wrong?

Hello,I am preparing to develop a custom board based on the STM32MP15 series MPU and getting accustomed to the DDR testing procedures in the STM32Cube ecosystem with an STM32MP157F-DK2 evaluation board. However, I am running into issues with the SYSRAM loading option which seems to be the necessary method for DDR testing new, custom boards designed around the STM32MP157 MPU.Firstly, I am able to run the DDR Test Suite in STM32CubeIDE or STM32CubeMX after importing the STM32DDRFW-UTIL-main\DDR_Tool\STM32MP157C-DK2 project into STM32CubeIDE. I am able to run the test firmware on the evaluation board with the "Debug As" option (with boot switches set to Engineering Mode), and then I am able go to a new .ioc project file made for the STM32MP157F-DK2 (peripherals initialized in their default modes) and use the DDR Test Suite via the "DDR Interactive" mode with no issues. Similarly, I can open a serial connection in TeraTerm via the ST-LINK COM port and run the DDR tests there

hi st experts:I am porting stm32mp2 software to my own robot board(stm32mp257D), after i finished my yocto build, i tried to download image to my board, there was a problem, it seems reconnect devices failed,  STM32Cubeprogrammer log:  12:53:51 : STM32CubeProgrammer API v2.18.0 | Linux-64Bits 12:54:00 : UR connection mode is defined with the HWrst reset mode 12:54:00 : USB speed : High Speed (480MBit/s) 12:54:00 : Manuf. ID : STMicroelectronics 12:54:00 : Product ID : DFU in HS Mode @Device ID /0x505, @Revision ID /0x2000 12:54:00 : SN : 002B00254136501800353059 12:54:00 : DFU protocol: 1.1 12:54:00 : Board : -- 12:54:00 : Device ID : 0x0505 12:54:06 : Read TSV File: /mnt/ext_disk/code/myb_github/build-openstlinuxweston-zero-robot/tmp-glibc/deploy/images/zero-robot/flashlayout_zero-robot-image-core/optee/FlashLayout_emmc_zero-robot-stm32mp257x-2GB-optee.tsv 12:54:06 : Number of partitions: 14 12:54:14 : Start Embedded Flashing service 12:54:14 : Opening and

 Hello, I am looking for a MPU as CAN FD master but couldn't find the type with explicit CAN FD support. I would inquire here to make sure I haven't missed any details, and also ask for more information about the availability of the high performance chip with CAN FD interface. Thank you!

I try to build a rpmsg sample app by following this instruction : https://docs.zephyrproject.org/latest/samples/subsys/ipc/rpmsg_service/README.htmlThe example repository here: https://github.com/zephyrproject-rtos/zephyr/tree/main/samples/subsys/ipc/rpmsg_serviceIt seems that the device tree overlay is missing for STM32MP157F-DK2, so I create one/ { chosen { /* * shared memory reserved for the inter-processor communication */ zephyr,ipc_shm = &mcuram2; zephyr,ipc = &mailbox; }; mcuram2: mcuram2@10000000 { compatible = "mmio-sram"; reg = <0x10000000 0x40000>; };It is not working, please advice if the device tree is correct or not? and Is there any relation with Linux device tree? thanks 

Hi,When testing the stm32mp2-openstlinux-6.6-yocto-scarthgap-mpu-v24.12.05 image, the LVDS screen doesn't work and blocks the board's startup (in u-boot) and I can't reset the board unless I disconnect the LVDS port.On the other hand, the HDMI is functional, and the screen works without any problem on my STM32MP257F-EV1 board.Note that the board is powered via a USB port capable of delivering up to 1.5A.Thank you

Hello,I am encountering an issue while building a Yocto-based image for the STM32MP157F-DK2. The problem arises when attempting to fetch the gcnano-userland-multi-binary-stm32mp package. Below are the details of the issue: Project DetailsYocto Version: Dunfell (OpenSTLinux 5.10-dunfell-mp1-23-11-01)Target Machine: STM32MP157F-DK2Recipe Name: gcnano-userland-multi-binary-stm32mpSoftware Version: gcnano 6.4.3Issue DescriptionThe fetch operation fails due to a missing source file. Specifically:http://downloads.yoctoproject.org/mirror/sources/git2_github.com.STMicroelectronics.gcnano-binaries.tar.gzHowever, this file is unavailable, and the fetch results in a 404 error.Here is an excerpt from the build logs:http://downloads.yoctoproject.org/mirror/sources/git2_github.com.STMicroelectronics.gcnano-binaries.tar.gzResolving downloads.yoctoproject.org (downloads.yoctoproject.org)... 2a01:4f9:3070:3985::2, 37.27.135.249Connecting to downloads.yoctoproject.org (downloads.yoctoproject.org)|2

i am getting issue to install Tkinter . error - E: Unable to locate package python3-tkdoes we can not install Tkinter in STM32MP1 ? if there is anyway to install it then please let me know .

Hi all, Does anybody knows why there is no stm32mp157f-dk2 device tree for https://github.com/STMicroelectronics/u-boot/tree/v2025.01-rc4?   make ARCH=arm stm32mp15_defconfig make DEVICE_TREE=stm32mp157f-dk2   Following commands work with stm32mp157c-dk2 but thats not the board I am using Regards