MEMS (sensors)

Hi,I'm using IIS3DWB MEMS sensor to get the motor vibration data which will have a bandwidth of 6kHz and need to store it to a 16GB SD cardI'm confused to calculate the data rate, i mean what is the ODR i need to consider?My calculation is :ODR = 26667 and 3 axis 6 bytes, which becomes 160kb/s and 12.89GB/day precisely, which is a lot of data for a dayShould i consider the ODR to be 2x times the bandwidth (6kHz in this case)?Also let me know about the raw data and how can i filter out the 6khz frequency data that i need

Folks,I have an STM32 rigged up via SPI to read gyro data-only from an LSM6DSL. I read it periodically, every 20ms, and for a while it will report back a few hundred samples in FIFO STATUS REG 1 and 2; I empty the FIFO and after another 20ms it reports me a few hundred samples available and so on. After a short time though it reports no samples in the FIFO and after that it will never have any data to report until I reset and restart.Is there a technique for this? Can I not just read out every so often? We don't have the interrupt line connected to the micro, so it has to be done on a polling basis.I can imagine that maybe if you didn't empty the FIFO quickly enough that there might be a bug in the silicon and it might always read back zero, *but* I have set watermark to 2048 and stop on full, yet it still falls over.This is at 1.66k ODR (both gyro AND FIFO). If I run it st a slower ODR it works OK.At 833Hz, the next rate down, I always

ST moderator: Duplicated threads merged. In next time please don't duplicate the same topic.   The ASM330LHH datasheet CTRL3_C (12h) says:Note: The accelerometer must be ON. This bit is cleared automatically. This bit is cleared automatically. Does ON for the accelerometer mean that ODR_XL[3:0] in the CTRL1_XL (10h) register is set to a non-zero value?

Hello everyone, I'm new to both BLE and MEMS sensor. I want to combine 2 examples code as following:STMems_Standard_C_drivers/lis2dux12_STdC/examples/lis2dux12_mlc_activity_mobile.c at master · STMicroelectronics/STMems_Standard_C_drivers · GitHub STM32WBA Bluetooth® LE – Serial communication - stm32mcu so that i can send MEMS events via BLE/USART. Could someone give me support or instruction, how to combine ?

HelloI have a problem with the accelerometer lsm303agr and the Fifo Stream mode, I have a time offset between 2 watermark interrupts.Configuration :- accelerometer only- watermark interrupt enable on int1- bdu enable- Stream mode enable- Fifo enable- Don't used any gesture recognition, or filter.- i use the spi mode at 500khzDescription of the problem :I used the accelerometer in Fifo Stream mode, the watermark to fire the interrupt on pin int1 when a certain number of data in the Fifo is reached.The odr is at 1hz, i used the rtc of the stm32 (from a homemade board) to collect the timestamp when INT1 trigger.I have notice a time offset for every sample in addition of the ODR configured.I measured it to be around 25ms/samples on top of my 1seconds period (odr 1hz).I checked the timing at the oscilloscope which confirmed that the problem Don't come from the reading of the rtc

I am completely new to using the STEVAL-MKBOXPRO (Sensor Tile.Box Pro) sensor, and I have a problem accessing some of the functions in the ST BLE Sensor app. I can connect the sensor in the app, but when I try to plot the data within the app, I cannot choose anything in the drop-down menu other than "MemsSensorFunctionCompat", whereas I should be able to choose between that, gyroscope, accelerometer and magnetometer.I cannot find the function "Flow" on the bottom of the list with all the options. That is where I am supposed to be able to choose between basic apps and create my own apps in expert mode, but I cannot access it for some reason.More info: I am using the newest version of the new app (not the classic one, but I have tried that too; it also doesn't work), I have deleted and redownloaded it, paired and disconnected from the sensor multiple times. Thank you to anyone who has some information about this in advance!

After activating the accelerometer and angular rate sensor, the temperature sensor value does not change and appears to be frozen. What is the cause of this?Is there any countermeasure?

Hi,I am working on an application where I need to generate an interrupt whenever a tap exceeds a certain acceleration threshold. I have already chose the IIS2DLPC for this purpose.However, on page 58 of the datasheet, in Table 67 for the TAP_THS_Z register, I found the following:"TAP_THSZ_[4:0] Threshold for tap recognition @ FS = ±2 g on Z direction."I would like to clarifyDoes that mean that taps above 2g can't be detected. My application requires detecting relatively strong impacts, ideally up to 4 g, and preferably up to 8 g.If this is possible, could you advise on how to configure the device to achieve this?If it is not feasible, could you recommend any alternative accelerometers from your product line that would meet these requirements?Thanks in advance!  

How to distinguish whether the product LIS3LV02DL is 11+ or 21+ by the printing on the product? There is only a "1" on the product( And no label( 

I am using the ASM330LHH connected to the processor via 4-wire SPI communication. I’m trying to read the WHO_AM_I register, which should return 0x6B according to the datasheet, but I keep getting 0xFF. The CS line is set correctly before and after the transfer. What could be causing this incorrect data read? If the device isn’t found (WHO_AM_I doesn’t return 0x6B) and I still try to read accelerometer and gyro data, and I am getting data, will those values be completely random?

I am developing a wireless sensor to detect vehicles using the IIS2MDC. My main logic is:BOOT -> Init sensor -> Measure environment -> Set detection thresholds and offsets based on environment -> Set interrupts -> Wait for interrupt On interrupt -> Acquire vehicle heading -> Send RF signal to gatewayAfter some hours working properly the sensor starts sending continuous signals without a vehicle or other metalic object nearby. How can i correct this behaviour? Any help is welcomed. Below i'll leave the application code for the IIS2MDC initialization: CFG_REG_A is always 0x90CFG_REG_B is always 0x09CFG_REG_C is always 0x50INT_CTRL_REG is 0x00 on startup and 0x45 on work mode #define IIS2MDC_STARTUP_CFG {0x90, 0x09, 0x50, 0x00} #define IIS2MDC_WORK_CFG {0x90, 0x09, 0x50, 0x45} bool iis2mdc_startup_

Can I operate ODR_XL[3:0], FS[1:0]_XL and LPF2_XL_EN of CTRL1_XL of ASM330LHH simultaneously?Should I set FS[1:0]_XL and LPF2_XL_EN first and then set ODR_XL[3:0]?

Should INT2_CTRL (0Eh) in ASM330LHH be changed when ODR_XL[3:0] in CTRL1_XL is 0, or should it be changed after being set to non-zero?

Hello everyone, I am currently using the LSM303AGR's magnetometer and accelerometer. After coding the self-test procedure from the datasheet, and noticed that the number of samples for the magnetometer self-test is way higher than the number of samples for the accelerometer self-test (5 for the Accelerometer, 50 for the Magnetometer). When looking at the Application Note (AN4825: ultra-compact high-performance eCompass module based on the LSM303AGR), the number of samples to average is 5 at page 21/65 - Magnetometer self-test), whereas it is 50 in the next figure at page 22/65 (Figure 3. Magnetometer self-test procedure). Which one should it be ? Thanks in advance, CJ

Hello,i am trying to run the self test procedure on the lis3dh according to Application Note 3308 but for some reason the  output change (13 lsb) is below the minimum value listed in the lis3dh (17lsb) .If i run the procedure multiple times in a row immediately after each other, it only fails the first test consistently. I assume as the test applies a electrostatic test force, the charge somewhat is retained on the sensor for a short time therefore the output change is higher.The code was run on multiple lis3dh therefore i don't think this is a hardware issue, i also can read the WHOAMI Register just fine.Here is a sample of my self test implementation: const lis3dh_ctrl_reg2_t ctrl_reg2 = { 0 }; lis3dh_write_reg( &imu, LIS3DH_CTRL_REG2, (uint8_t *)&ctrl_reg2, sizeof(ctrl_reg2)); const lis3dh_ctrl_reg3_t ctrl_reg3 = { 0 }; lis3dh_write_reg( &imu, LIS3DH_CTRL_REG3, (uint

I would like to implement a low pass filter to filter out noise at frequencies above 2Hz on the IIS2ICLX inclinometer. I would like to have as high an ODR as possible, let's assume 833Hz. My signal has a low frequency, around 0.5Hz.LPF1 will clearly not help me - the response is flat out to 100Hz.To implement the filter using LPF2, would the following register configurations be suitable:CTRL1_XL : ODR bits 0b0111 for 833Hx ODRLPF2_XL_EN bit 0b1 to enable LPF2CTRL8_XLHPCF_XL bits 2:0 set to 0b110 for cutoff of ~2Hz (=833Hz ODR / 400)HP_REF_MODE_XL set to 0b0 to disable HP filterFASTSETTL_MODE_XL set to 0b0 to disable fast settling modeHP_SLOPE_XL_EN set to 0b0 to disable slope filter I would be extremely grateful for any help implementing my filter - thanks for reading this far!

If the TDA bit is not set to “1” even once after 400ms has passed after the sensor is turned on, is it likely that the startup has failed?

I am using the MLC of the LSM6DSOX along with the Nucleo-L432KC. I am using the .h file generated from the examples provided by ST (STMems_Machine_Learning_Core\application_examples\lsm6dsox\Motion_intensity\lsm6dsox_motion_intensity).uint8_t LSM6DSOX_MLC_config(LSM6DSOX_HandleTypeDef *LSM6DSOX, I2C_HandleTypeDef *hi2c) { uint8_t ret = 0; for (uint32_t i = 0; i < sizeof(lsm6dsox_motion_intensity)/sizeof(ucf_line_t); i++) { ret = HAL_I2C_Mem_Write(hi2c, LSM6DSOX_I2C_ADDR, lsm6dsox_motion_intensity[i].address, I2C_MEMADD_SIZE_8BIT, (uint8_t *)&lsm6dsox_motion_intensity[i].data, 1, HAL_MAX_DELAY); } return ret; }In the main loop, I check the value of MLC0_SRC LSM6DSOX_ReadRegister(&LSM6DSOX, 0x70, &gesture);However, the value is always 0. I als

Dear All, Is there anyone tested "STEVAL-PROTEUS1" board for sensor node application. When I test "Cloud logging" demo from App, by right I should be able to see list of available Azure IOT central PNP applications, like "Proteus POC". However, there is nothing application available in PNP configuration page of App.Your valuable suggestions are most welcomed to advise how to send sensor node data to Azure IOT central cloud.

Hi Expert, Good day. Refer to the attached label image. One label shows MSL 1 and the other shows MSL 3 for MPN LIS2DW12TR. However, the Reliability Evaluation Report for this P/N indicates MSL 1. Both labels have the same COO but different MSL levels. Is it possible or Is there any PCN behind this change? [images deleted by a moderator] Looking for your support on this.   Thank you. Ivan Paul

What is the default value of HP_SLOPE_XL_EN in the CTRL8_XL (17h) register of ASM330LHH?

I am using the LSM6DSV80X to get roll-pitch-yaw from SFLP and gyro reading. I noticed that the sensor keeps reporting increasing yaw and increasing offset for X axis while at rest even though the data sheet suggests that it should have up to only 1dps offset. How do I fix this?Settings:Accelerometer full-scale: 16gGyro full-scale: 4000dps (also show 4dps offset and yaw at 500dps)ODR: 480 for accelerometer, gyro, and SFLPThank you

 Hello,        In my case, the STHS34PF80 sensor module is powered using I2C communication with the ESP32 module, and I have tested its functionality only up to 2 feet; beyond that, it fails to detect any presence. However, the datasheet indicates that it should cover 4 meters without a lens in an 80-degree field of view. What might be the reasons for this discrepancy?

Hi,My question is in regard with SLEEP_DUR of the register WAKE_UP_DUR.Datasheet "LSM6DSV16X" (p98) mentions:Duration to go in sleep mode. Default value: 0000 (this corresponds to 16 ODR) 1 LSB = 512/ODR_XL time"Whereas the "AN5763" (p60) instead specify:SLEEP_DUR_[3:0] bits of the WAKE_UP_DUR register: 1 LSB corresponds to 514 / ODR_XL time, where ODR_XL is the accelerometer output data rate. If the SLEEP_DUR_[3:0] bits are set to 0000, the duration of the inactivity state to be recognized is equal to 18 / ODR_XL time.Not that the very similar specs impact product design itself, however I would prefer to know the correct one.Thank you,

How long does the TDA bit in the STATUS_REG of the ASM330LHH remain “1”?Is the TDA bit itself a latch type and remains “1” until the temperature output register (OUT_TEMP_H/L, 21h/20h) is read?