MEMS (sensors)

Dear SIR,​I have found a polling mode reference code in the following linkhttps://github.com/STMicroelectronics/STMems_Standard_C_drivers/blob/master/lsm6dsr_STdC/examples/lsm6dsr_read_data_polling.c​The code demonstrates that after reading b'1 of XLDA bit or GDA bit,it is OK to read XL data or Gyro data.​But on page 20(Fig.1 below) and 25(Fig.2 below) of AN5358 "LSM6DSR: always-on 3D accelerometer and 3D gyroscope", it tells us that user needs to discard the data number, which depends on the LPF2 or HP filter setting or ODR.My question is if polling mode is used, read the STATUS_REG and get th

Hi, folks,I'm using LIS2DE12 on the PCB. The purpose: the device should inform the firmware, if the PCB has moved - intruder detection. I successfully programmed the device for INT1 on 6D movement. It works fine in general.On the PCB I have also a small (10mm) piezo buzzer. As soon as the buzzer sounds, LIS2DE12 detects a movement. The distance between LIS2DE12 and the buzzer is about 3cm (1.2"). I watched the data from LIS2DE12 during the buzzer run and I saw really a wild dance on X/Y/Z axies.Well, I do understand, that the buzzer causes the vibrations, but did not expect to see values +/- 0.4g and more! The accelerometer has only a high pass filter (to exclude the DC components) but no low pass filter to cut off anything above 1kHz (actually, the buzzer runs at 4kHz - at its own resonance).Do you have any ideas to avoid false positive detection while the buzzer is running?P.S. reducing the samplin

Hi there fellas, I'm using the HS_Datalog to measure some vibrations. At first, I used the Python SDK, but now I'm trying to use the libhs_datalog_64.dll in a c# Application. I can get the device info, start and stop the log, set some parameters like ODR or FS, but it seems that I'm doing something wrong when I try to pull my data from the st board. I can save it, but I cannot export with the Python SDK afterwards. Furthermore, I would also like to load the *.json Config File on the board using the hs_datalog_send_message(...). Can somebody tell me what the correct format of the message is? Can I get some more documentation on the HS_Datalog.h ?

Hi there,I am working with the H3LIS100DL Accelerometer. I am able to get readings back and it seems to work fine.My question is: what is the reading that I am getting back for the X (Reg 0x29), Y (Reg 0x2B), and Z (Reg 0x2D)? Does 1 digit equal ~1g? I have looked through the datasheet and unlike another accelerometer from ST that specifies how many 'g' 1 digit is, the datasheet for this accelerometer does not appear to have that information.Thanks,Christian

I have the imu 10dof and i got raw data of accelerometer, gyroscope and magnetic. And i calculate the roll, pitch, yaw base on equation same in picture. i had calibrate accelerometer and magnetic. in the picture, show the data of magnetic before and after calibrate. But the yaw angle is not linear. I rotate the imu from 0 to 30 degree but yaw data is 0 - 5 degree, rotate the imu from 30 to 60 degree but yaw data is 5 - 15 degree, rotate the imu from 60 to 90 degree but yaw data is 70 - 115 degree.my english is not good, please help me.thanks!

LSM303DLH has CLICK register to setup it but LSM303C has only commont THS and DUR registers set, can I use it to detect single tap event? As I understand I can setup AND config for all axis, but it doesnt work so good and I can get false detection for some angels of devicevoid LSM303C_AccConfigTapOnInt1(void) { uint8_t reg_val = ACCELERO_IO_Read(LSM303C_CTRL_REG3_A) | 0x08; /* interrupt on INT1 */ ACCELERO_IO_Write(LSM303C_CTRL_REG3_A, reg_v);   reg_val = 1; ACCELERO_IO_Write(LSM303C_IG_THS_X1_A, reg_v); ACCELERO_IO_Write(LSM303C_IG_THS_Y1_A, reg_v); ACCELERO_IO_Write(LSM303C_IG_THS_Z1_A, reg_v);   reg_val = 100; ACCELERO_IO_Write(LSM303C_IG_DUR1_A, reg_v);   reg_v

Dear ST Community,Ten days ago I already asked this support request but no one single response came from ST.I just bought and received an ST-EVALMKI109V3 + ST-EVAL212V1 after attending the webinar "Develop effective AI solutions for monitoring vehicles using a single sensor".I get this error that says it does not know the chip id when I select the MKI212V1 as shown in the screenshot above.All my software tools seem to be on the latest revisions. Anyway I updated the board with the last firmware using this v

Hi,I am debugging my custom board where I soldered an LIS2DW12 accelerometer on it. I forgot to pull the reserved pin ( 7 ) to ground as suggested in the datasheet. This is how I connected it:This is how it should be connected:Is this required, that the accelerometer can work properly? I cant find it on my I2C bus and don't know if it is related to this little mistake or maybe another, most likely soldering issue.Edit: I2C is pulled up and dec

Please, Help

Hello,I have connected my amicam1 with the nucleo L476RG and 2 IMP23ABSU (from STEVAL MIC007V1) on respectively M3 and M4 of AMICAM1.I used the microphone streaming example ( from memsmic1 V5-6) and configure amicam1_conf.h with modifying AUDIO_IN_CHANNELS to 4 and AUDIO_IN_SAMPLING_FREQUENCY to 96000.No problems in compilation but impossible to see and record 4 channels (MO1, MO2, M3 and M4) with audacity !What are my problems ?Thanks for the help.Jérôme

Hello Team,We would like to measure the vibration using LIS2DW12 (3-axis MEMS accelerometer), from the LIS2DW12 we were getting units in 'g' or 'mg'.Please let us know the possibility of converting g to dbVrms.Best regards,Abishek Devan

We are looking at using the LIS2HH12 in a design where the connected MCU is powered off and the LIS2HH12 remains powered on. We plan to use the LIS2HH12 in I2C mode so CS will be High. Will cycling Vdd_IO from 3.3 to 0 to 3.3V generate spurious I2C signals? Other questions we have are:Will the INT1/2 signal operate correctly when Vdd_IO = 0V? We want to use one of these signals to wake-up the MCU.If we set CS = 0V, will that reset the I2C logic in the LIS2HH12?There is a way through the registers to Soft Reset the LIS2HH12. Are there other ways to reset the I2C bus if it gets 'stuck'? Ideally, we do not want to put a separate power switch in for the LIS2HH12.Thanks all for any answers or feedback.

Hi, We have a PCB design which used to have LSM6DSL and we were using ACC/GYRO data from the sensor. Since we switched to the new LSM6DSR chip the INT1 does not trigger (when data is ready) anymore even though the sensor should be similar config (if not the same). What could be reason for this? The chip responds with NACK from commands which were used to work on LSM6DSL. Worth mentioning that INT2 triggers as expected w/o issues, but not INT1.Regards.

I'm trying to use the UNICO Pedometer Regression tool in offline mode to analyze accelerometer data from the LSM6DSO32 accelerometer. I have followed the instructions from the UNICO user manual regarding data format:-file name data_steps138.txt-data sampled at 26Hz-+/-8g full scale-data formatted to mg and tab separated, with x, y, and z axis data in that order on each line. Every time I try to run the tool I get a popup error at 1% completion saying "cannot open regression_tool.config". After closing that pop-up, the main window says "error: cannot generate configuration file". I have check the root UNICO folder and find no evidence of either file. Help debugging this issue would be much appreciated.

I have a stm32f3discovery board and I want to start playing with the LSM303DLHC MEMS sensor.I seem to have found the original example code on github.So I guess I need to add both the header and c file to my project. I'm not sure how to go about this. Also, what is this procedure called? Am I "adding a library"? Or is it called a driver?

Hello, We have found a non-expected behavior of the IMU system LSM9DS1 when is set with an accelerometer scale = +-16g. To show our findings, it is presented below descriptions and diagrams of the tests.Firstly, two different devices were tested to contrast one with a scale of +-8g and the other with +-16g. The devices are stationary with the Z-axis aligned with gravity. Hence, after multiplying by the range scale and dividing by the digital value, we should obtain values close to 1g in the z-Axis. However, as is shown below, one can observe that in the case of 16g, the values from the Z-axis are around 0,65.  

Hello, I'm facing issues when enabling LIS3DH click interrupt, AOI1 and AOI2 interrupts on INT2 pin. These interrupts works fine on INT1 pin. Following is the flow I do to enable click interrupt on INT2 pin. register - 20h value - 119  //ODR 400Hz and all axis enabledregister - 21h value - 0 //HPF disabledregister - 22h value - 0  //No interrupt enabled on INT1 pinregister - 23h value - 8  //High resolution output mode register - 24h value - 0  //Interrupts not latchedregister - 25h value - 128 //Click interrupt on INT2 pinregister - 38h value - 5  //Detect single click on x-axis and y-axis register - 3Ah value - 10 //Threshold 1.5m/s^2 register - 3Bh value - 120 //Time limit 0.3sregister - 3Ch value - 120 //Time latency 0.3sregister - 3Dh value - 120 //Time window 0.3s.

LIS331DLHTR,The first line is tracking code,The second line represent the chip,The third line represent the date code.

Hello,I'm trying to understand the LIS2DE12 behaviour. First, there is no AN (Application Note), thus I used the one for LIS3DH which seems close enough.What I want is that my accelerometer wake up my stm32. This works. After that I just want to read 1 sample to know the current acc value. But the FIFO system seems a problem for me. In the doc, it says the sample I get is the oldest one in the FIFO and that if I don't read fast enough data will be overwrited.I just want to read one sample for Z-Axis when I need in my code. Do you have any idea or clue?Thanks.Best regards, Simon

I tried following this tutorial (https://community.st.com/s/question/0D50X0000BYnQt6/sensortilebox-not-connecting), but it looks like DfuSe is obsolete, and I should use the new STM32CubeProg tool. I couldn't seem to find any information on how to use the STM32CubeProg tool to restore to defaults. How do I use STM32CubeProg to restore to defaults?

Dear SIR,When FIFO mode is disable. And Polling mode is used.There is a bit DRDY_MASK in registerCTRL4_C(0x13), 1 : mask DRDY on pin (both XL & Gyro) until filter settling ends (XL and Gyro independently masked).It says that it mask DRDY on pin, it dos NOT raise interrupt INT1 or INT2 until filter setting ends.When polling mode is used, does it means that it mask bit XLDA and GDA to b'0 when filter is not complete(data is not ready)in STATUS_REG?Thanks,E-John 

HelloWe must replace the old LSM6DS with the new one LSM6DOX because of End of Life of the first one.Checking the results on the same jig, reveals half of the Accelerometer part of the new chip. Do you have a detailed documentation which may support with all the differences between them?What should be change (in setup or in FW) in order to have the same results between them?Thanks!

Hi,I am using the LSM6DSL, i can see that the chip marking is different for some of my chips,some have SF 951 and others have 952. Further, I am getting different sensor results from each, Does someone know what is the difference between them?Thanks

Hello,We are working on tilt feature development based on LIS2DW12 sensor.For the development of the tilt feature with the help of Wakeup interrupt and following the attached example belowSo, How to set the sensitivity value from the open to the close position? (Please refer to the below example) 

Hi, i'm using LIS2DS12 accelerometer in FIFO continuous mode connected to my MCU using the I2C interface. i'm setting the FIFO threshold to 80 samples and using the maximum ODR of 6400Hz so it takes ~12.5ms for the FIFO interrupt to read it. reading the 80 samples takes ~4ms using I2C in 1MHz speed. all data is read in one I2C transaction.examine the received data, it seems that some of the samples data is missing which fits the time it was reading the FIFO, 4ms that are 25 samples. it looks that new samples are not entering the FIFO while reading the FIFO.is the LIS2DS12 supporting filling new samples to the FIFO while reading the FIFO?is it a configuration issue?Thanks, Roei.