STM32 MPUs Products and hardware related

Hello,  I was wanting to make my own camera board and I wanted to use the same camera that is on STM's Camera board MB1854 and I looked up that manufacturer part number (AS-BC538A3M6-63(1.02.A3265)) and nothing showed up, and when I looked up just AS-BC538A3M6-63 then the only result was STM's example schematic for the MB1854 camera board. I then tried looking up the company they listed on the BOM (HONGJIA) and still found nothing. Does anyone know how to find the board or even some contact info for that company?  ThanksCarson 

Hello, I have STM32MP135F-DK board and raspberry pi camera module v2.1 but board does not see cameraI guess I have to modify stm32mp135f-dk.dtb file.  But how should I write settings like OV5640 or GC2145 in dtb filelike that   gc2145: gc2145@3c { compatible = "galaxycore,gc2145"; reg = <0x3c>; clocks = <&clk_ext_camera>; IOVDD-supply = <&scmi_v3v3_sw>; AVDD-supply = <&scmi_v3v3_sw>; DVDD-supply = <&scmi_v3v3_sw>; powerdown-gpios = <&mcp23017 3 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; reset-gpios = <&mcp23017 4 (GPIO_ACTIVE_LOW | GPIO_PUSH_PULL)>; status = "okay";   port

Hi,I am trying to understand and test secure boot on STM32MP1. I was able to compile and boot unsigned tf-a. boot failed as expected as it is not verified.generated keys.Now how to burn these below hash file? can we burn into flash and test without using OTP for development and POC?publicKeyhash.binThank you.

Hi,I was wondering if ST or any ST Partners are planning to produce a System-on-Module (SoM), System-in-Package (SiP) or Single Board Computer (SBC) based on the new STM32MP257 chips?We're planning to develop using the STM32MP257F-DK evaluation board then find a SoM, SiP or SBC that supports the STM32MP257's MIPI CSI-2 interface and ability to quickly wake from a low power sleep mode.Will

 Hello ST Team and Community,I'm working with the STM32MP257F-DK board and exploring the provided AI demo examples. I noticed that most of the camera-related demos (especially those involving image inference or real-time processing) are designed around libcamera as the default source, as indicated in code snippets like:parser.add_argument("--camera_src", default="LIBCAMERA", help="use V4L2SRC for MP1x and LIBCAMERA for MP2x")While I understand that libcamera is appropriate for MIPI-CSI cameras (which MP2x supports), I'm currently using a USB UVC camera, which libcamera does not support.From what I know, USB webcams work well with V4L2 but are ignored by libcamera due to its pipeline design.My

  Is it mandatory to use a MIPI display in order to boot the system successfully? Is it not possible to boot using only an HDMI display? 

I have been experiencing mixed results when booting up and programming a custom board using STM32MP131DAG7. Some of the custom boards boot up and program without issues. Other boards do not boot up or program. All the custom boards were built at the same time as part of the same batch. I would like some troubleshooting assistance Details of my custom board:STPMIC1DPQR to power the STM32MP131Switches on BOOT[0-2] to select the boot mode.Onboard eMMC and SD card slot.USB port for DFU via STM32_Programmer_CLI.exe to program the eMMC. On some of my custom boards, I successfully program the eMMC and the board will boot up into the OS perfectly fine. These boards also boot up via SD card perfectly fine when I set the BOOT switches to select SD card boot. Everything on the custom board functions as normal after successful program.&

Hi,At my company, we develop debuggers and are trying to access STM32MP257F-EV1(ES) board via the DAP,Unfortunately, we are unable to access the DAP and it seems like JTAG (DAP) access is prohibited by hardware.The result was the same even after shorting JP3 and turning off ST-LINK.I have the following questions:Are there any other jumpers positions that have to be changed? Please let me know.Does STM32MP257F-EV1(ES) have debug authentication enabled by default?If so, please let me know if there are any technical documents that explain the procedure for debug authentication.I tried to connect to the on-board debugger by running STM32CubeProgrammer and choosing ST-LINK (SWD), but access was denied.The boot mode that I tried were "UART/USB" and "Deve

Running through the instructions to flash an eMMC chip via STM32CubeProgrammer.Board is custom based on STM32MP157F-DK2, boots great off a SD card (SDMMC1).I can communicate and load uboot via both USB and UART...uboot can get basic data off the eMMC with `mmc dev1; mmc info`   but uboot fails to enter DFU mode to continue the process, and running dfu complains about the lack of a USB device. I've tried all sorts of RAM, etc dfu examples.From the uboot shell:```STM32MP> dfu 0No USB device foundusb_gadget_initialize failedSTM32MP> print dfu_alt_infodfu_alt_info=ram 0=uImage ram 0xc2000000 0x2000000;devicetree.dtb ram 0xc4000000 0x100000;uramdisk.image.gz ram 0xc4400000 0x10000000&mmc 1=mmc1_boot1 raw 0x0 0x400000 mmcpart 1;mmc1_boot2 raw 0x0 0x400000 mmcpart 2&virt 0=OTP&virt 1=PMIC STM32MP> usb devno usb devices availableSTM32MP> usb rese

Hello, we are currently designing a STM32MP257 based custom board. For reference, we are looking into STM32MP257F-EV1 and STM32MP257-DK evaluation kit schematics. In both schematics, there is an STM32 MCU which connects to the JTAG ports of the STM32MP257. Is this MCU used as an STLINK to provide JTAG to USB2.0 conversion? If so, if we are to implement the same structure on our board, is there a way to access the STLINK firmware and embed it into our own MCU? Furthermore, is there an external STLINK adapter dedicated for STM32MP25 series MPUs to access JTAG over USB?My second question is that can we program the MPU using the JTAG pins? Both in reference manual and datasheet of the MPU, there doesn't seem to be a boot mode setting for JTAG. 

HiI have stm32mp157c in my custom board i connect sai2 to codec(tlv320aic), i config sai2a as master (WITHOUT MASTER CLK OUTPUT) and sai2b as synchronous slave, mclk for codec come from rcc mco1 and this is my dts:  sound {// compatible = "audio-graph-card", "simple-audio-card";compatible = "audio-graph-card";label = "AUDIOcard1"; routing ="Playback" , "MCLK","Capture" , "MCLK";dais = <&sai2a_port &sai2b_port>;status = "okay"

HiWe are working on development of SOM based product with STM32MP257FAI, we are looking for STPMIC25 IBIS model for IR drop and decoupling analysis. Could you please share the model 

Hi,I have an STM32MP135F-DK board and I would like to know if to follow the steps in the video below I just need to install STM32CubeIDE on a computer running Linux or if I need to install something first?https://www.youtube.com/watch?v=qEzfqKt3exEFor example, is it necessary to follow the steps corresponding to the links below first, or does the STM32CubeIDE installation itself and the sequence of steps in the video already do this?https://wiki.st.com/stm32mpu/wiki/Getting_started/STM32MP1_boards/STM32MP135x-DK/Develop_on_Arm%C2%AE_Cortex%C2%AE-A7/Install_the_SDK

Hello,We have a custom board based mainly on stm32mp257-dk design. The sdcard supply voltage doesn't activate on STPMIC for some reason. Is the stpmic preprogrammed on the DK board or should the Rom code of the MPU activate it via I2C? Best RegardsRaimo

I understand that the STMCube environment doesn't function as a BSDL (Boundary Test) tool. Can anyone suggest a free tool that is compatible with the ST-LINK-V3SET?Keysight, Corsair, XJTAG are out of my rangeMy application is gather tools for board bring-up for our STM32MP255F prototype PCB.Thank you. 

Following the instructions at https://wiki.st.com/stm32mpu/wiki/How_to_start_the_Cortex-M_coprocessor_from_U-Boot#Manual_start I try to load and run an M33 app from U-Boot.Within the U-Boot console I managed to load the elf file from the boot partition. But I can't load the file to the M33 coprocessor using rproc.rproc is available in the console, but doesn't show any coprocessor:STM32MP> rproc init Remote Processors are already initialized STM32MP> rproc list STM32MP>  My board is from MYIR with an stm32mp257D MPU on it using:- I/TC: OP-TEE version: 3.9.0-3162-g355cb55d2 (gcc version 12.3.0 (GCC)) #1 Fri Nov 1 10:58:57 UTC 2024 aarc- U-Boot 2022.10-stm32mp-r2 (Nov 07 2024 - 02:59:13 +0000)CPU: STM32MP

Hi,I'm just getting started with C programming for embedded Linux using the STM32MP13x. My applications are mostly IoT applications.I'd like to know which IDE is best for beginners, between STM32CubeIDE and Visual Studio Code.And where can I get information on how to configure these IDEs to compile and debug user-space C applications remotely?Ari 

HelloWe are using the STM32MP257F in M33TDCID flavour using the packagestm32mp2-m33td-openstlinux-6.6-yocto-scarthgap-mpu-v25.06.11We can boot and run the Non Secure application, but when we try to use some of the peripherals (I2C, SPI, GPIO)we see processor exceptions or Resource Manager issues.How do we configure the device to allow the Non-Secure application access to all the peripherals Thanks  

Hello,I am working with a SOM based on the STM32MP157C and I am trying to bring up a display panel that uses the Sitronix ST7703 MIPI DSI controller.The operating system has been built with Yocto using the BSP provided by the SOM vendor. This BSP is based on Linux kernel 5.4, which unfortunately does not contain the upstream panel-sitronix-st7703 driver.Has anyone already backported the ST7703 panel driver to Linux 5.4 for STM32MP1 platforms? Or does anyone have guidance on how to integrate this driver into an older kernel version?Any hints, patches, or references would be greatly appreciated.Thank you in advance!

Hello.We are developing a device with the STM32MP257 and we will not have a USB Type-C connector in our design. We plan to use the USB3DR as a USB2.0 device with a USB 2.0 connector to USB boot (USB boot for flashing). Does the STM32MP2 embedded bootloader uses the UCPD CCx signals?How can we inform the USB3DR about detection of the USB VBUS?Is is possible to emulate UCPD CCx signals (sink mode) from the USB VBUS as a variant of detecting the incoming USB power?Best regards,Vadim Aleynikov

On DK2,  ADC is used to measure the voltage on cc lines, how to skipcan u give me the yocto steps to follow on commenting the following line in uBoot Device Tree:do u have to create a new layer or can we edit the patch file in the uboot device tree and build it.

 "is there possibility we can auto mount a usb when connected to usb host and how to build the udev-extraconf package for my stm32mp157f-dk2" how to build this   please give the steps to build for my stm32mp157f-dk2 as i want my pendrive to mount automatically                                                                                                                                                                       /home/sharan/STM32MPU/Distribution-Package/layers/openembedded-core/meta/recipes-

I have had difficulties programming the STM32MP257 via stm32cubeide. I followed the first few steps to flash an OS image onto the board using the section populate and boot the image, from the STM website. When trying to flash IOC generated code via stm32 cube ide It gives me an ethernet over usb error if I have just the ST-LINK connected, but when I connect to the DFU usb, it seems like it will flash for a moment and throws this remoteproc error. I think it may be a secure boot issue with the stlinux, but im not sure how to get around this or what options I have.

Dear All,I'm having problem to get DFU over USB running on custom board.In general device can boot from SD card and with no SD card it can be detected via uart4 by STM programmer, so it enters DFU as far as I can tell.USB DP/DM is connected to DP2 (being pulled-up to ~3.3V) and DM2 (looks like a weak pull down). OTG_ID (PA10) hangs free and OTG_VBUS (U15) hangs free.3V3_USBHF+FS connected to LDO4 and present (3.3V)EDIT: 24Mhz xtal present, no 22Ohm series resistors and also removed all esd protection at this moment...Nothing happens on the USB lines when I connect the cable to the PC and the device is not detected. The voltage on the OTG_ID pin is LOW - which is strange, as is should be pulled up theoretically. Connecting OTG_VBUS (PA10) pin to VBUS from the connector does not change anything, that is - no detection, no communication, looks like my device behaves like a host.I could not find any reference design for USB connection, bu

Hello Experts,Based on STM32MP257F-EV1 we have designed a custom board. For the DDR, PMIC, and eMMC we tried to follow the EV1 rooting as much as possible. There are few differences on the BOM though: Our DDR chips are Alliance Memory AS4C1G16D4A-62BCNOur eMMC is a Kingston EMMC32G-TS0A-01002We have build an image that can be flashed into the EV1's eMMC without any issues. Things go differently when we try to flash our 2 prototypes.  The first prototype stops after having properly downloaded the partition 0x3 fip-stm32mp257f:12:15:04 : Number of partitions: 14 12:15:29 : USB speed : High Speed (480MBit/s) 12:15:29 : Manuf. ID : STMicroelectronics 12:15:29 : Product ID : DFU in HS Mode @Device ID /0x505, @Revision ID /0x2000 12:15:29 : SN : 0029002A4C4250110038344D 12:15:29 : DFU protocol: 1.1 12:15:29 : Board : -- 12:15:29 : Device ID :