STM32CubeProgrammer (MCUs)

 Hello everyone,I have a .hex and a .bin file that set an output to high/low on an STM32H745.When I upload the .hex file, my project works correctly, but when I upload the .bin file, it doesn't work.I'm sharing both files.I can't figure out what I'm doing wrong. Can you help me?

I was happily debugging some code in my NUCLEO-F207ZG, the whole morning the debug sessions (stm32cubeIDE) have been quite glitchy.Until the mcu somehow got briked and i cannot revive it.I suspect noise in the SW lines comming from some external LEDs nearby had something to do with this issue, or power fluctuations when programming.I am unable to Read the FLash content so i connected the board to the stCUBEProgrammer.12:42:36:814 : STLinkUSBDriver.dll loaded 12:42:36:819 : STLinkUSBDriver.dll loaded 12:42:36:819 : ST-LINK SN : 066FFF323239524257191044 12:42:36:820 : ST-LINK FW : V2J39M27 12:42:36:821 : Board : NUCLEO-F207ZG 12:42:36:821 : Voltage : 3.24V 12:42:36:836 : SWD freq : 4000 KHz 12:42:36:837 : Connect mode: Under Reset 12:42:36:837 : Reset mode : Hardware reset 12:42:36:838 : Device ID : 0x411 12:42:36:850 : Revision ID : Rev 2.0 12:42:36:871 : flash loader C:\Program Files\STMicroelectronics\STM32Cube\STM32CubeProgrammer\bin/FlashLoader/0x411.stldr is loaded 12:4

I tried an uninstall and reinstall of STM32CubeIDE V1.14 (this version is a project requirement), but there has been no change in the behavior. That target board is a NUCLEO-F413ZH. I have never seen this behavior before on a variety of other NUCLEO boards using STM32CubeIDE V1.8.Console:STMicroelectronics ST-LINK GDB server. Version 7.5.0Copyright (c) 2023, STMicroelectronics. All rights reserved.Starting server with the following options:Persistent Mode : DisabledLogging Level : 1Listen Port Number : 61234Status Refresh Delay : 15sVerbose Mode : DisabledSWD Debug : EnabledInitWhile : EnabledWaiting for debugger connection...Debugger connectedWaiting for debugger connection...Debugger connectedWaiting for debugger connection...-------------------------------------------------------------------STM32CubeProgrammer v2.15.0------------------------------------------------------------------- Log output file: C:\Users\rob\AppData\Local\Temp\STM32CubeProgrammer_a23412.logST-LINK SN : 066

Dear Community Teams, My name is Cong, and who currently perform projects with smt32. However, there is one error that I need advice from you if possible.The description of the error as below:- Environment used: Windows 10- Board: SMT32N657X0-Q- Tool: SMT32CubeProgrammer - Description: This is the first setup for my board SMT32N657X0-Q.I used the SMT32CubeProgrammer to connect the board.From my laptop: I saw it can connect to my laptop via ST-LINKS After that, I used the smt32cubeprogrammer tool and configuration for ST-Link as the second photo (Reset mode: Software reset), I received the error:  04:10:41 : Error: Unable to get core ID  04:10:41 : Error: No STM32 target found! If your product embeds Debug Authentication, please perform a discovery using Debug Authentication When I changed the reset mode to: Hardware reset, I received an error as Third photos:04:20:12 : Error: Data read failed In this case, I saw the tools can read the board stm32N657X

I've just noticed that STM32CubeProgrammer (2.19.0) can't see network disk on my Windows 10 PC.I have also set a folder inside of one of the network disk as favourite folder to rapid access on the left sidebar but, when I click it via STM32CubeProgrammer Explorer it says the path is invalidThe network disk is at X:// 

STM32f334 在Stm32cube programmer中如何不改變RDP的情況下，驗證MCU內部程式為正確的，透過找出沒有被RDP1鎖住的FLASH去驗證，或是如何透過改寫OB來驗證? Translation: How to verify the correctness of the internal program of STM32f334 MCU in Stm32cube programmer without changing RDP, by finding the FLASH that is not locked by RDP1, or by rewriting OB?  

Hello, I am unable to connect to STM32L562-DK via STM32CubeProgrammer , and when I do I get this error message13:12:59 : Error: ST-LINK error (DEV_TARGET_NOT_HALTED)Could someone please help me rectify this issue, Thanks  

Hello,I am working on a project where a device is updated using dfu-util and utilizes the DFU driver from the STM32Cube(Programmer) drivers subdirectory. I would like to distribute these drivers to my customers and need to know, for the FOSS Software Bill of Materials (SBOM), what license is used for these files. I understand that stm32bootloader.inf and cat are licensed by STM under the SLA0048 license. Is that correct?However, what license is used for files such as WdfCoInstaller01009.dll and winusbcoinstaller2.dll? Where can I find the license information for these files? Are those property of Microsoft or STM?Is this the appropriate place to ask this question, or would there be a better forum for it?Thank you and regards,Ben 

Hi,I've tried to program OTP area of STM32U575 at address 0x0BFA0010 with a quad-word (4x32bit of data) but only half are programmed (the first half) while the 2 remaining words are at 0xFFFFFFFF (erased state) and cannot be programmed anymore.I've loaded a binary file with 128bits of data, chose the download attress at 0x0BFA0010 and pushed the download button.Accoding to the datasheet the flash must be programmed 128bit at once: is that implemented in the programmer?Best regards, Diego

Hi,I have been trying to integrate JLINK-SWD, USART, FDCAN and USB DFU interfaces for Open Bootloader for STM32G473 Device, with the STM_Programmer_CLI.exe on Windows (Latest - V2.17.0 64-Bit)  and when I prompt to list out the communication interfaces available below are the observations: 1. In case there is no ST-Link Device Connected, there is no listing of the UART Ports. (as show below)Figure 1 - UART Ports not listed - No ST-Link ConnectedCOM3 is detected in Device Manager - UART COM Port detected on device manager2. In case there is ST-Link Device Connected, then the UART Ports are listed. 3.This issue is not present in the STM32 Cube Programmer GUI, on refresh the UART Ports update in the GUI Drop-Down.4. With V2.13.0 the issue still persisted same as earlier.V2.13.0 Log 5. In order to verify the issue, installed STM32 Cube Programmer (V2.6.0). And in this version the issue is not present, But since it is an older version I am assuming that the J-Link I

Hi!I am working with CubeProg 2.15 and a STM32H743XI. When using the register view window with peripheral ImpDef there is bug in the register addresses: ITCMCR is correctDTCMCR is correctAHBSCR 0xE000EF90 (0xE000EFA0 would be correct) -> content of ITCMCR is shown twiceCACR is correctAHBPCR is correctABFSR is correctIt would be nice if the registers could appear in increasing register address orderITCMCRDTCMCRAHBPCRCACRAHBSCRABFSRBest regardsGerald 

ST Link not recognizing STM Cube Programmer? - From screenshot you can see pulls up single character serial number and has no target information. I can (and did) upgrade firmware to latest on ST Link. Downloaded all drivers etc. Still won't connect. Keep getting "UR connection mode is defined with the HWrst reset mode" log entry.   

I've been experimenting with STM32F765VGT6 (custom board made by a colleague) and STM32F769NIH6U (on a STM32F769I-DISCO). Please correct me as soon as you see a mistake.I did not "play" a lot with the F769. As long as I did, everything seemed as expected.I'm focused on the F765 now, with which I have problems.Both MCUs Option Bytes are configured in 2 banks mode : nDBANK is unchecked.  Flash size :- the F765 has 1 MB :- the F769 has 2 MB Bank 2 start address, as from RM :- F769 : 0x08100000- F765 : 0x08080000 Problem : I found it impossible to flash my code at 0x08080000 on the F765.STM32CubeProgrammer returns :15:52:48 : Opening and parsing file: MCU_F765_LwIP_NoFreeRTOS-0.1.0-0x08080000-0080E10666A0.bin15:52:48 : Memory Programming ...15:52:48 : File : MCU_F765_LwIP_NoFreeRTOS-0.1.0-0x08080000-0080E10666A0.bin15:52:48 : Size : 120.95 KB 15:52:48 : Address : 0x08080000 15:52:48 : E

Hi ,I am using STM32WL33 in my design and just received my first PCB assembled.i am trying to flash the board with basic program but no success yet , it would be great if you can help to find the problem.i have tried with both CubeIDE and Cubeprogramer with STlink V2 , seems like debugger is connected but not going to further steps .here is the screen shotsi have used same ST linkV2 and setup in another board (STM32WLE5) and i can connect.  schematic:  I checked the SWDIO, SWCLK, VDD, GND and NRST pin connection to ST link it looks okayI checked the voltages VDD : 3.3V, VCAP:1.2V , NSRST:3.3V , VFBSD(SMPS output):1.4VNo pullup resistor in NRST and PA10 pin is floating.Circuit is design based on ST reference designAny help is appreciated //Karthik  

if we don't make a full erase, this error comes up.I hoped it would disappear with V2.18

I am using the STLINK-V3SET. I have tried both the JTAG and SWD headers. 10:03:14 : UR connection mode is defined with the HWrst reset mode10:03:15 : ST-LINK SN : 00260035353251103133343010:03:15 : ST-LINK FW : V3J15M7B5S110:03:15 : Board : STLINK-V3SET10:03:15 : Voltage : 3.26V10:03:15 : Error: Unable to get core ID10:03:15 : Error: No STM32 target found! If your product embeds Debug Authentication, please perform a discovery using Debug Authentication BOOT0: Pulled to GND (0V) through 10k pull-down resistorNRST: Pulled to GND through 0.1uF capacitorSWCLK (PA14), SWDIO (PA13) tied directly to header pins. I have tried to discover using Debug Authentication, I've tried disabling and enabling shared. I've tried lowering the frequency to 50khz and 5khz from 8000 khz. I have my PCB gnd and 3.3V tied to the STLINK-V3SET as well.I've also tried multiple MCU's.One of the problems with my schematic is I have a 24mhz clock tied to the LSE input rather than the HSE inpu

Dear All, On my NUCLEO-U575ZI-Q I have successfully generated USBX-DFU and have come to a point to connect to it with STM32CubeProgrammer. It seems to be very simple, there are six callbacks only:USBD_DFU_Activate and USBD_DFU_Deactivate does not return anyting, so I have left them as is;In USBD_DFU_GetStatus I set the media_status to UX_SLAVE_CLASS_DFU_MEDIA_STATUS_OK and return USBD_DFU_Notify;In USBD_DFU_Read I set the actual_length = length and return UX_SUCCESS;In USBD_DFU_Write  I set the media_status to UX_SLAVE_CLASS_DFU_MEDIA_STATUS_OK and return UX_SUCCESS;In USBD_DFU_Notify I return UX_SUCCESS.That does not work however. STM32CubeProgrammer connects but immediately reports "Error: Data read failed". In debugger I see that it stucks on requesting status, USBD_DFU_Read is not ever called. Has anyone idea what exactly should be returned by the USBD_DFU_GetStatus?  Regards,Dmitry

After Install launching returns CubeProgrammer_API is missing. Please try reinstalling or check you java architecture. Ive seen some other forum posts with this issue and tried to fix the java version to no avail.Current java version is java-1.8.0-openjdk.x86_64Ive also tried a liberica version  bellsoft-java8-full.x86_64console output of error, I can see the files that were failed to load in the file system so I believe it was installed properlyNative code library failed to load: java.lang.UnsatisfiedLinkError: Unable to load library '/home/eastwor/STMicroelectronics/STM32Cube/STM32CubeProgrammer/bin/../lib/libCubeProgrammer_API.so': Native library (home/eastwor/STMicroelectronics/STM32Cube/STM32CubeProgrammer/bin/../lib/libCubeProgrammer_API.so) not found in resource path ([file:/home/eastwor/STMicroelectronics/STM32Cube/STM32CubeProgrammer/bin/STM32CubeProgrammerLauncher]) System I'm running on is rocky8 Linux x86_64

Hi,I am currently working with the STM32L562E-DK Discovery board and attempting to flash Trusted Firmware-M (TF-M) samples on Zephyr using the STM32_Programmer_CLI tool.However, I have encountered an issue during the flashing process. Error Output:(.venv) kurodash@ubuntu:~/zephyrproject/zephyr$ west flash -- west flash: rebuilding [0/15] Performing build step for 'tfm' ninja: no work to do. [2/3] Performing install step for 'tfm' -- Install configuration: "MinSizeRel" ----- Installing platform NS ----- [3/3] Completed 'tfm' -- west flash: using runner stm32cubeprogrammer ------------------------------------------------------------------- STM32CubeProgrammer v2.18.0 ------------------------------------------------------------------- ST-LINK SN : 00380025313751XXXXXXXXXX ST-LINK FW : V3J15M7 Board : STM32L562E-DK Voltage : 3.28V SWD freq : 8000 KHz Connect mode: Under Reset Reset mode : Hardware reset Device ID : 0x472 Revision ID : Rev Z Device name : STM32L5xx Flash size : 51

 

I just downloaded and installed both STM32CubeIDE and STM32CubeProgrammer.They both forcibly installed with user-spying phone-home features how I use the software, while only mentioning how to disable the feature after they have been installed.So, the spying feature is on by default, and there is even no option to opt-out of the feature at install stage.I don't believe this is GDPR compliant and thus illegal in the EU. Please fix this before someone makes a GDPR report of this and you get fined.If you start harassing your users with spying features, I can also start taking my money elsewhere and buy other MCUs.

我使用 H750VBTx 芯片读取寄存器0x1FF1E7FE返回值如下所示参考 https://community.st.com/t5/stm32cubeprogrammer-mcus/stm32cubeprogrammer-2-18-0-released/td-p/747840 文章，我的芯片的 bootloader 版本是否无法使用 stm32cubeprogramme2.18.0 对外部 qspi 闪存进行编程？我在哪里可以获得 \bin\ExternalLoader 文件夹中的最新可用例程？哪个版本的 CubeProgrammer 有这个例子？非常感谢愿你安好 

I am following the very first step with STM32L562E-DK, to run a .bat file ..But I received error: Initializing the option bytes failedSame in CLI too..How can I recover my board? any hardware reset? 

Moved from this thread (new question) Hello, I have installed the STM32G4 patch for IAR (from the STM32CubeG4 repository) on IAR Embedded Workbench 8.22.3. After applying the patch: The STM32G431RB appears in the device selection list. The project builds successfully. However, flashing & debugging fail with the following error:   Failed to load flash loader: C:\Program Files (x86)\IAR Systems\Embedded Workbench 8.22.3\arm\config\flashloader\ST\FlashSTM32G43xxB.flashError while calling macro execUserFlashInit   What I Have Tried:Manually set Flash Loader to FlashSTM32G4xxx.flash instead of FlashSTM32G43xxB.flash.Disabled "Verify Download" in IAR Debug settings.Reduced SWD Speed to 1 MHz.Replaced flashloader files from the patch. Questions:Which is the correct flashloader file for STM32G431RB?Does the STM32G4 patch officially support IAR 8.22.3, or do I need IAR v9+?Is there an updated STM32G4 flashloader for older IAR versions?Any additional settings needed in IAR to mak

Hi to allI just wan't to use the CLI inteface from STM32CubeProgrammer and I don't want to installl the full SMT32CubeProgrammer which is about 1.3GB.Is there a Standalone Version from the STM32CubeProgrammer CLI?Best regards