STM32CubeProgrammer (MCUs)

Looking for something to try. I'm want to recover from a failed firmware update of an MLite-880 from Elecevolve after their their 1-click installer. Elecevolve suggested a manual install using the firmware binary and STM32CubeProgrammer. I can put the device in its "DFU FW update mode" and connect to the device from the STM32CubeProgrammer using USB. After connect, the log shows:08:45:07 : STM32CubeProgrammer API v2.22.0 | Windows-64Bits08:45:35 : Disconnected from device.08:46:01 : USB speed : Full Speed (12MBit/s)08:46:01 : Manuf. ID : MALAHITEAM08:46:01 : Product ID : Malahit-Lite DFU08:46:01 : SN : 305B376E313308:46:01 : DFU protocol: 1.108:46:01 : Board : --08:46:01 : IAP08:46:01 : UPLOADING ...08:46:01 : Size : 1024 Bytes08:46:01 : Address : 0x800000008:46:01 : Read progress:08:46:01 : Data read successfully08:46:01 : Time elapsed during the read operation is: 00:00:00.053When I click Start Programming, literally nothing happens except the progress bar at the bottom previous

I have a STM32N6570-DK and i can't seem to program it any more.  I tried it in both the STM32 programmer gui and terminal application.  So i can connect to the device read and read the flash but i can't seem to write to it any more.  I can't even erase the flash.  I have another  Boot 0 = 0 (L)Boot 1 = 1 (H)     

Dear,When running the FSBL that includes HAL XSPI initialization logic on the Nucleo-N657X0-Q board (MB1940-N657X0Q-C02), the flash erase with the STM32CubeProgrammmer v2.22 sometimes fails. However, if I leave out the XSPI initialization logic for accessing the NOR flash, flash erase always succeeds. BOOT pin 1 is set to DEV and I am loading the FSBL firmware directly into RAM.Do you have any idea why XSPI Init causes the flash erase to fail ?BR,EdwinD 

Hi, I've just installed v2.14.0 for the first time, but it will not start up. All I get is the blue STM screen for a few second, then it disappears. I tried the command prompt start up detailed in This Post but I end up with an error message, shown below. I need help on how to proceed as I do not have JRE installed on my PC, but have had it in the past. I've tried re-installing STM32... but that didn't help Exception in Application start methodjava.lang.reflect.InvocationTargetExceptionat sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method)at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:62)at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43)at java.lang.reflect.Method.invoke(Method.java:498)at com.sun.javafx.application.LauncherImpl.launchApplicationWithArgs(LauncherImpl.java:382)at com.sun.javafx.application.LauncherImpl.launchApplication(LauncherImpl.java:321)at sun.reflect.NativeMethodAccessorImpl.invo

Hi,I am using the STM32CubeProgrammer API (v2.20.0) on Windows 11 using the Visual Studio UART example as a base. Everything works fine, however this issue is slowing down the programming workflow.After programming the MCU option bytes to RDP1 (or Closed state on some newer devices), there is a long delay (20 to 30 seconds) during the attempts to reconnect to the device. I already expect that the reconnection attempt will fail, so is there a way to reduce the time or number of reconnection attempts? Or a way to cancel the current operation? The time taken for failed reconnection attempts is 2x longer than the actual programming of the MCU.I noticed that there is a getCancelPointer() function in the API, but I have found no documentation or examples on how to use it. Is it possible to use this or is there some other way?Edit: Added info - using UART to program the device/** * \brief This routine allows to drop the current read/write operation. * \return 0 if there is no call for

I have an old Ubuntu 18.04 system which allows STM32CubeIDE to run, but the STM32_Programmer failed because libm.so and libc.so were wrong. I found glibc-2.30 and copied the libraries into the same directory as the STM32_Programmer lib. Now I just get a seg fault, even when trying to just get the version number:bin/STM32_Programmer_CLI --version Segmentation fault (core dumped)Is there any way to figure out what might be the problem?   

Hallo zusammen,mir ist im STM32CubeProgrammer (GUI, v2.19.0) ein merkwürdiges Verhalten im Automatic Mode aufgefallen:Wenn man den Haken bei "Run after programming" direkt aktiviert und dann auf „Start“ klickt, wird kein Reset ausgeführt, obwohl die Option gesetzt ist. Das Programm wird nicht neu gestartet. Wenn man schnell hintereinander viele Platinen updaten will mit Neustart des Programms ist dies hinderlichWorkaround:Wenn man den Haken einmal entfernt und dann wieder setzt, funktioniert der Reset im Automatic Mode anschließend wie erwartet. Offenbar wird die Option intern erst korrekt übernommen, wenn sie aktiv verändert wurde.Das Verhalten ist reproduzierbar und tritt unabhängig vom Ziel-MCU auf (getestet mit STM32L4 und ST-Link v3MINIE).:wrench:Vorschlag:Es wäre super, wenn das in einer der nächsten Versionen behoben werden könnte – vermutlich reicht ein Fix im Initialisierungsverhalten der GUI.Viele GrüßeBB-RTB Translation:Hello everyone,I noticed some strange behavior in

I have been programming my STM32H743 custom board for over a year.  Suddenly I'm getting the error message Error: No STM32 target found... I have tried changing the ST-Link itself but get the same error message.

Hello, Iam working o STM32H573I-DK Board when am trying to access board am getting trustzone issue.I tried with Debug Authentication also but am unable to access board.Find the attached description. 

I am working with the STM32N6-GettingStarted-ObjectDetection demo.  I found that doing a full chip erase wipes some bootloader code.  I was able to get my project going again by flashing the .hex file that came with the STM32N6-GettingStarted-ObjectDetection demo, the loading my code. Digging around on the net suggested that the prebuilt demo has a bootloader.  I have been unable to locate the bootloader.Can you provide me with the bootloader, preferably as a .hex file?

Dear all, I have an arm Ubuntu system and would like to use the st32programmer. Unfortunately, ST provide only this code for Intel Linux machine Any chance to have this tool ready for arm Ubuntu machines? Kind regards, Edo  

..

Hi. I have a request. Is it possible to compile STM32CubeProg for arm linux?Right now it is possible to compile firmware for stm32 on arm linux using the stm32duino toolchain from ST.However, the STM32CubeProg is only available on intel linux. This means we can compile firmware on an arm system such as Raspberry Pi 4, but there is no official tool to upload the firmware.Note I'm not asking for the whole STM32Cube IDE - just the STM32CubeProg cli would be sufficient.

Hello, I have managed to use stm32flash to flash custom binary to the STM32 through the raspberry pi.This involves moving BOOT0 to 0V, pressing reset and running the command.I can also include -R to software reset the STM32 after this is finished.I then decided to try using a GPIO from the PI to change BOOT0 from 3.3v to 0V and this also works but I still have to manually press the reset button on the bluepillI have read the following but finding it a little hard to understandGPIO sequence: - entry sequence: GPIO_3=low, GPIO_2=low, GPIO_2=high - exit sequence: GPIO_3=high, GPIO_2=low, GPIO_2=high stm32flash -R -i -3,-2,2:3,-2,2 /dev/ttyS0Are these GPIO pins from the Pi or from the STM32?How do I connect this?I thought about applying 0V to the reset pin on the STM32 but I see a capacitor is used and this is further confusing.The reason I need this is for firmware updates to the STM32 and flashing new sketches through the Pi without the need for user input or manual pressing of the reset

STM32CubeProgrammer has a C++ API which allow to create program compiled using qt creator. Is it possible to compile for linux os and run in rasperry os which is debian based?

..

Is it possible to program a STM32G071 from a raspberry pi running Raspbian OS? Is there a USB to serial driver for this?

I don't see ARM 32/64 bit in the system requirements of STM32CubeProg. Is it possible to get this running on like a raspberry pi 4? I am interested in CLI onlyor do you have other suggestions on how i could do a flash of stm32 chip (STM32G070CB)

Per the title really - I've just tried to install the Linux version on a raspberry pi running Raspbian / Debian 11.7 'Bullseye' and, well, NOTHING happens.If I click 'SetupSTM32CubeProgrammer-2.16.0.linux' nothing happens at all, if I select "execute in terminal" I get a brief flash of a terminal window, a mystery file of 0 bytes is created (named with a single unicode character and 'P').If I run it from the terminal I get:$ ./SetupSTM32CubeProgrammer-2.16.0.linux-bash: ./SetupSTM32CubeProgrammer-2.16.0.linux: cannot execute binary file: Exec format error  Also why is a tool for programming microcontrollers a 286Mb download for which we must give ST our blood type and inside leg measurement just to be allowed to download it? :flushed_face:

Hi,I would like to use a Raspberry Pi to program the STM32F722RET6 micro controller via the RPI UART. My Problem is, that the Cube Programmer is not made for ARM architecture, so it cant run on the Pi.I cant find a solution for this, apart from emulating a x86 environment on the PI which I would like to avoid.Is there any simpler version of the Programmer which could run on a Raspberry PI?Thank you for your help.

It would be nice if the further versions could be running on case sensitive file system on macOS.Currently I need to use an USB key formatted APFS only. Then i can run the installer and install the programmer on this USB stick. As I most of the time only need the command line tools (*CLI) I copied the binaries and some folders with data on my case sensitive disk. They work fine. Only the GUI is not possible on the case-sensitive file system. 

Hi,I would like to program the STM32F091 with the internal bootloader via UART (AN2606).My special case is that I have to do the programming not from a PC, it's a another embedded system that will control the programming of the STM32F091.So I'm looking for source code (C or C++) that I could migrate in my embedded system?Does this exist?Thanks