STM32 MCUs Embedded software

Hi,How do I serve request Get Source Capabilities Extended? I'm using STM32G0B1 with a port configured as SRC.When a SINK sends the Get Source Capabilities Extended the STM PD library responds with 'Not Supported' and my code is not aware that this even did happen. Is there way to intercept and serve this request? At least the callback structure does not appear to have direct support for this. USBPD_DPM_ExtendedMessageReceived is never called. /* CAD callback definition */ static const USBPD_PE_Callbacks dpmCallbacks = { USBPD_DPM_SetupNewPower, USBPD_DPM_HardReset, USBPD_DPM_EvaluatePowerRoleSwap, USBPD_DPM_Notification, USBPD_DPM_ExtendedMessageReceived, USBPD_DPM_GetDataInfo, USBPD_DPM_SetDataInfo, USBPD_DPM_EvaluateRequest, USBPD_DPM_SNK_EvaluateCapabilities, USBPD_DPM_PowerRoleSwap, USBPD_PE_TaskWakeUp, #if defined(_VCONN_SUPPORT) USBPD_DPM_EvaluateVconnSwap, USBPD_DPM_PE_VconnPwr, #else NULL, NULL, #endif /* _VCONN_SUPPORT */ USBPD_DPM_EnterErrorR

Hello,On a STM32H7RS are using the USB_OTG_HS peripheral in PCD_SPEED_FULL mode using internal clock.After I was able to configure the clock so that the MCU is responding on enumeration requests. The responses however seem to be partially incorrect; the trace tool shows stalls.I did not found an example in current https://github.com/STMicroelectronics/STM32CubeH7RSThe following changes are applied to a CubeMX generated projectmain.c SystemClock_Config:LL3.PLLN was set to output 24 MHzRCC_OscInitStruct.PLL3.PLLState = RCC_PLL_ON; RCC_OscInitStruct.PLL3.PLLSource = RCC_PLLSOURCE_HSI; RCC_OscInitStruct.PLL3.PLLM = 4; RCC_OscInitStruct.PLL3.PLLN = 60; RCC_OscInitStruct.PLL3.PLLP = 2; RCC_OscInitStruct.PLL3.PLLQ = 40; RCC_OscInitStruct.PLL3.PLLR = 16; RCC_OscInitStruct.PLL3.PLLS = 2; RCC_OscInitStruct.PLL3.PLLT = 2;Configure CRS __HAL_RCC_CRS_CLK_ENABLE(); RCC_CRSInitTypeDef RCC_CRSInitStruct = {0}; RCC_CRSInitStruct.Prescaler = RCC_CRS_SYNC_DIV1; // default RCC_CRSInitSt

Hello, I am currently using the NUCLEO-U545RE-Q and trying to set low-power modes with FreeRTOS. I have already seen videos from official ST channel and read documentation but I cannot get to set this functioning when using FreeRTOS and RTC. My goal is to blink an LED every 5 seconds and in the reamaining time go to STOP mode for low power consumption. This are my functions: void StartDefaultTask(void *argument) { /* USER CODE BEGIN defaultTask */ /* Infinite loop */ while(1) { osSemaphoreAcquire(BinarySemaphoreHandle, osWaitForever); printf("Toggle Led\n"); BSP_LED_Toggle(LED_GREEN); } /* USER CODE END defaultTask */ } /* Private application code --------------------------------------------------*/ /* USER CODE BEGIN Application */ void HAL_RTCEx_WakeUpTimerEventCallback(RTC_HandleTypeDef *hrtc) { printf("RTC Callback\n"); osSemaphoreRelease(BinarySemaphoreHandle); } void PreSleepProcessing(uint32_t ulExpectedIdleTime) { HAL_SuspendTick(); /* Start low power timer

Hi, I try to get the USB-Host running with USBX. Hardware is a custom board with TCPP02 and STM32U575. Init process is running, but I never get an interrupt (ux_host_event_callback) when plugging in a USB stick. Any idea? ioc file and schematic are attached. Best regards, Achim

Hey there,I'm currently working on an audio application for the STM32U5A5 (which I'll later port to the STM32N657), using MDF.The application closely follows the MDF/ADF examples for audio recording found in the U5/N6 Cube firmware packages, with the difference that it does not output the transformed audio signal immediately via SAI, but instead stores it in a large buffer to download it later via the STMCubeProgrammer.Although the application generally works great, it does not record more than ~2 seconds of audio, even if I increase the size of the storage buffer (e.g., to a size corresponding to 4 seconds of audio recording capacity). No matter how large I set the buffer, the function HAL_MDF_AcqCpltCallback is called approximately 2 seconds after the recording starts. Within the implementation of this function, HAL_MDF_AcqStop_DMA is called to stop the recording.I would be interested in the criteria according to which the HAL_MDF_AcqCpltCallback function is called. I would

Hello, I want to use an I2C port of a STM32F411 MCU (MCU_A) in target mode to receive data from another MCU (MCU_B), MCU_B code already existing and verified with other receivers.I configured the project with STM32CubeMX, with interrupts enabled to handle communication in interrupt mode.I used MX standard settings to generate CubeIDE project with HAL code.With some effort for setting up the initialization and other code for MCU_A in CubeIDE, communication looks ok from sending MCU_B perspective.Additional check of SDA and SCL signals with DSO looks ok to. But the problem was: No data was transfered to the receive data buffer in MCU_A. After several hours of debugging, I found a suspicious code section in the HAL code (stm32f4xx_hal_i2c.c).In the HAL function     static void I2C_Slave_ADDR(I2C_HandleTypeDef *hi2c, uint32_t IT2Flags)which is called in     HAL_I2C_EV_IRQHandler ()when adress matches, the direction flag received from MCU_B

Hi everyone,I’m relatively new to embedded systems, so apologies if this has already been discussed elsewhere. I’ve tried searching, but haven’t been able to find a clear solution.I’m currently developing a system based on the STM32F746G Discovery board using TouchGFX for the touchscreen UI. In addition, I’m interfacing with a distance sensor over I2C. My goal is to log data (timestamp + sensor value, already formatted) to an SD card.The issue I’m facing is the following:When I enable only SDMMC and FatFS in CubeMX, I can successfully open a file and write data to it.However, when I integrate this functionality into my full project (which includes TouchGFX, FreeRTOS, and I2C), the SD card logging no longer works.I’d really appreciate any guidance or suggestions on what might be causing this or how to approach debugging it.Thanks in advance!

Hello,I think I have interesting case, but from the beginningI use STM32F446ZEJx and HAL Drivers from STM32Cube_FW_F4_V1.28.3.When I use HAL_StatusTypeDef HAL_SPI_TransmitReceive_DMA(SPI_HandleTypeDef *hspi, const uint8_t *pTxData, uint8_t *pRxData, uint16_t Size)with Size=5 it internally checks the argumentif ((pTxData == NULL) || (pRxData == NULL) || (Size == 0U)) return HAL_ERROR;and passes the Size to/* Set the transaction information */ hspi->ErrorCode = HAL_SPI_ERROR_NONE; hspi->pTxBuffPtr = (const uint8_t *)pTxData; hspi->TxXferSize = Size; hspi->TxXferCount = Size; hspi->pRxBuffPtr = (uint8_t *)pRxData; hspi->RxXferSize = Size; hspi->RxXferCount = Size;later it configures the DMA channels,Rx/* Enable the Rx DMA Stream/Channel */ HAL_DMA_Start_IT(hspi->hdmarx, (uint32_t)&hspi->Instance->DR, (uint32_t)hspi->pRxBuffPtr, hspi->RxXferCount)Tx/* Enable the Tx DMA Stream/Channel */ HAL_DMA_Start_IT(hspi->hdmatx, (uint32_t

Hello, I am searching for a example project to integrate a camera (e.g OV-Series) via DCMI interface. Can someone recommend an ST-Project or else?   Thanks in advance!

Hello, Started to dwell info embedded development and got my hands on a NUCLEO-H7S3L8 development board. Firstly wanted to analyze the example code that comes with the development board and modify it a bit. But when started to debug, it seems to stop at I and D cache enable functions, and example LED blinking disappeared. Has anyone encountered something similar and could help to fix this problem? Only change I made to the example code is set-up a PC8 as a PWM to drive a LED switch. Additionally, tried a mass erase and re-flashing, but still nothing, the problems remains the same as I mentioned. 

Hello STM32 Community,I am developing a system on the NUCLEO-N657X0-Q using ThreadX and NetX Duo and I am having a hard time to make the ethernet work. I want to implement a web server in my system but I cannot make the Ethernet communicate.Problem:I am unable to receive or transmit any Ethernet frames. The PHY link establishes successfully (from what I see on my linux terminal, autonegotiation completes, Link is UP, and the LEDs on the plug turns on normally), but pinging the Nucleo's static IP yields no response. Wireshark shows no ARP or ICMP packets originating from the Nucleo.Trying to debug, I see that the the MAC/DMA interrupt `ETH1_IRQHandler` is never triggered by incoming network traffic. It fires exactly twice during the initial board boot sequence(where, for what I understand, some DMA errors flag are raised), but remains completely silent afterward. From the logs that I send to the serial port it appears that from the NetXDuo point of view is everything fine.The D-cache is

I would like to use some of your standard serial page eeprom'shttps://www.st.com/en/memories/standard-serial-page-eeprom.html The problem is that i don't understand how to use your memory loader with these chipshttps://github.com/STMicroelectronics/stm32-mw-extmem-ldr/tree/main  The problem is that this library expects the chips to have 4 byte address and just doesn't work with 3 address chips.  If you go through and just change all the call's to 3 byte address in the library i can make a STLDR file to talk to the chip.  Just trying to see if there's a better way.  You have this custom memory section that would help i just don't know how to use it?  So i'm hoping for some help there.https://github.com/STMicroelectronics/stm32-mw-extmem-mgr/tree/main/custom 

Hello everyone,I am currently trying to create a CMake based C-project for the ST Evaluation board STM32H757I-EVAL, that allows me to render a UI on the MIPI DSI connected display, that comes with it.Due to other work related requirements, I don't want to use TouchGFX, but will later try to add the LVGL framework to create our UI.However, at time of writing I have been unable to configure my project in such a way, that I can manually fill a Framebuffer and have that have any effect on the display. I have created a github repo with a "minimal" example of the configuration efforts so far.A "short" overview:I tried to create said CMake project through the STM32CubeMX code generator, and after a lot of trial, error and misunderstanding what is and isn't generated, I added the ST libraries for the external SDRAM "IS42S32800J" as well as the display driver IC "OTM8009A" and tried to configure the clocks and configurations of the following components:GPIO of the attached display pinsFMC to en

Hi, I’m working on a custom board based on STM32H757BITx using an external NOR flash Micron MT25TL01GBBB8ESF-0AAT TR (Dual bank with Quad Lines)Current usageAt the moment, the external flash is mainly used to store UI assets (images/fonts/etc.) for a display. I’m not using the full flash capacity, so I’d like to use an unused region to store a small persistent structure (configuration/status/log header).To keep things organized, I created a partitioning scheme using the linker file, reserving separate address ranges:UI assets region (read-only at runtime)User structure region (needs occasional write/erase/program)How it’s configured right nowSince up to now I only needed runtime reads, the flash is configured in Memory-Mapped Mode (DTR, QPI). I enable it with:MT25TL01G_EnableMemoryMappedModeDTR(&hqspi, MT25TL01G_QPI_MODE);This works great for reading UI assets through the mapped address space. ProblemI now need to write into the user structure region, but I unde

I'm trying to compile a basic blinky application for the N6 and failing. I open the latest CubeIDE, import the GPIO_Toggle project (or any other one for that matter) and try to build. I get an error about no rule to make target. Please provide guidance on how to build the basic examples 13:47:52 **** Build of configuration Debug for project GPIO_InfiniteLedToggling_Init_FSBL **** make -j11 all make: *** No rule to make target '/Users/workspace/STM32CubeN6-git/Drivers/STM32N6xx_HAL_Driver/Src/stm32n6xx_ll_exti.c', needed by 'Drivers/STM32N6xx_HAL_Driver/stm32n6xx_ll_exti.o'. Stop. "make -j11 all" terminated with exit code 2. Build might be incomplete. 13:47:52 Build Failed. 1 errors, 0 warnings. (took 83ms) 

HelloCurrently I am working with NUCLEO-N657X0-Q by using STM32CubeIDE_2.1.1 STM32Cube_FW_N6_V1.3.0MxCube v6.17.0Trying to investigate and migrate CDC ACM feature in to the my own project. As basis I am using Ux_Device_CDC_ACM Example provided by ST as reference.It was discovered that Ux_Device_CDC_ACM example would not work properly after MxCube project regeneration -- it goes to the HardFault_Handler() at some point (not defined currently at which point)The investigation showed that the issue is connected with the Optimization level (MxCube updated STM32CubeIDE project files) just only for the one single source file: "stm32n6xx_hal_rcc_ex.c". If optimization level is set to "-O0" for the mentioned file -- HardFault_Handler() is observed. By changing it to the "-O3" -- the application works successfully.Could you please explain this "hidden" dependency, and what is the reason of this?

Hi everyone,I am developing a project on the STM32N657X0H3Q where I need to implement a Dual CDC ACM composite device.I am following the "Standalone" implementation to avoid a full ThreadX dependency, as I plan to integrate this with a FreeRTOS project (using X-CUBE-FREERTOS).While looking at the USBX configuration in CubeMX and the ST Wiki (Introduction to USBX), I noticed the option USBD_COMPOSITE_USE_IAD ( As seen in the picture).If I enable USBD_COMPOSITE_USE_IAD , can I simply increase the number of CDC ACM class instances in CubeMX to 2?Does CubeMX automatically handle the IAD grouping for the second CDC instance, or do I need to manually adjust the interface descriptors in the generated ux_device_descriptors.c ?Can you provide an approach to configure this using MX? Which are all the files that should be edited to configure this.

Looking to add a 4 mic pdm array setup to livetune environment. Had questions on how deep into the environment we need to go for the changes. Is it just a matter of changing the # of channels for the sysIn, # of slots and active slots on the pdm interface? or do we need to drive deep as address the audio buffer as well. At one point I thought I read the audio buffer was allocated dynamically. We are just looking for a little guidance before we start changing things as there might be a simple way to achieve our goal vs us guessing and creating issues.

Hello, I am developing a project using the TCPP03 (X-NUCLEO-DRP1M1) and the ST USB-PD stack on an STM32G0 with FreeRTOS. I am concerned about the thread safety of the FLGn interrupt handling. In the standard BSP examples, the EXTI interrupt calls BSP_USBPD_PWR_EventCallback(). I2C Contention: Since BSP_USBPD_PWR_EventCallback() performs blocking I2C reads (ReadFlagRegister), what prevents the PE_Task or CAD_Task from attempting an I2C transaction at the same time? ISR Safety: In an RTOS environment, is it considered safe to perform blocking I2C calls inside the FLGn ISR, given the risk of HAL_BUSY or kernel priority issues? Best Practice: Does ST recommend a Deferred Interrupt pattern (e.g., using USBPD_DPM_CADTaskWakeUp) to move the I2C diagnostic logic out of the ISR and into a thread context?

Hi all! Thank you for taking time to assist me. I am attempting to make a composite USB Device on the NUCLEO-C562RE. I found the Middleware USBX examples and the core drivers exist in my toolchain at: STM32CubeC5/middleware/usbx However, I cannot seem to find the middleware configuration for USBX in STM32CubeMX2. My pack manager in the STM32CubeMX2 is set to this default value: "cube.packManager.cmsisPackRepositories": ["https://developer.st.com/st-pack-server/api/v1/pidx/STMicroelectronics.pidx"] Please let me know if I have missed anything or if you need further information from me to figure out the root issue. The examples, linked above, clearly auto generated the USBX files using the MX2 software, but I could not find the documentation that allowed me to generate those files. I would greatly appreciate it if someone could assist me with this.   EDIT: I saw this forum that says support isn't out until Q3. Does that mean I have to write the generated cod

Hello everyone,I am developing a firmware for an **STM32U5** microcontroller using Azure RTOS (ThreadX / USBX). I am implementing a USB Composite Device with two classes: **CDC** (Virtual COM Port) and **MSC** (Mass Storage Class). The MSC is interfaced with an eMMC using an 8-bit bus for data communication.I am facing a persistent issue that I cannot seem to resolve: the device drops the USB connection after about 5 to 10 minutes of operation. By debugging the code, I noticed that the disconnection is triggered because the device eventually calls the HAL_PCD_DisconnectCallback() function.My main concern (and source of confusion) is that this behavior is highly OS-dependent. For instance, on my dual-boot PC, the device works flawlessly without a single disconnection on **Ubuntu 22.04**, but it consistently crashes/disconnects on **Windows**.### What I see on Windows (Event Viewer)Right before the disconnection occurs, Windows throws several SCSI timeout errors in the Event Viewer. Spec

Using on a STM32H563RI with trustzone for a secure bootloader and non-secure application. Both the secure and non-secure side were correctly working in OPEN state, and I did a test of going to a CLOSED state and regression back to OPEN with authenticated debug. After the regression, RTC_EnterInitMode(), times out trying to enter init mode and HAL_RTC_Init() fails. I tried the solution from this form post of calling HAL_PWR_EnableBkUpAccess() and that did not work.Notes:- Trustzone and the secure watermarks for the bootloader were reprogrammed in the option bytes after regression.- RTC is LSI as its clock source.- The call to HAL_RCCEx_PeriphCLKConfig() in HAL_RTC_MspInit() returns HAL_OK.- The RTC pheripheral is marked non-secure.- The code has not been changed since preforming the regression and was working previously. The RTC Init Code and Clock configs are included below.void MX_RTC_Init(void) { /* USER CODE BEGIN RTC_Init 0 */ /* USER CODE END RTC_Init 0 */

STM32CubeMX 6.17.0STM32CubeCLT 1.21.0 which provides GNU Tools for STM32 which provides a toolchain with GCC 14.3 and newlib 4.5.0.STM32CubeH5 1.6.0 (as downloaded by STM32CubeMX)STM32H563 With these tools, you can easily generate a project which uses ThreadX as RTOS and NetX Duo as network stack by point and click in STM32CubeMX. In this case, the project is generated to use CMake and the GCC toolchain.NetX Duo requires some random numbers even for non-cryptography use cases. E.g. this code for allocating a random ephemeral TCP port so that the other endpoint doesn't think an old socket is reused when the MCU restarts for some reason: Middlewares/ST/netxduo/common/src/nx_tcp_client_socket_bind.c: UINT _nx_tcp_client_socket_bind(NX_TCP_SOCKET *socket_ptr, UINT port, ULONG wait_option) { ... /* Determine if the port needs to be allocated. */ if (port == NX_ANY_PORT) { /* Call the find routine to allocate a TCP port. */ port = NX_SEARCH_PORT_START + (UINT)(((ULONG)NX

Hello everyone, I am trying to bring up a NetX Duo TCP Server on the STM32H755ZIQ Nucleo board using Azure RTOS ThreadX + NetX Duo, but I keep running into issues during initialization and runtime. Unfortunately, I haven't been able to find any fully working examples for dual-core H7 devices using NetX Duo. Most examples online are either for single-core MCUs or for different boards. Here is what I am trying to achieve: STM32H755 Nucleo board M7 core running ThreadX + NetX Duo Basic TCP server (listening on a port, accepting connections, sending/receiving data) Using STM32CubeMX for configuration LwIP is NOT used — only NetX Duo Ethernet driver: nx_stm32_eth_driver (CubeMX generated).   It seems like the current CubeMX-generated NetX Duo code for the STM32H745/H755 series might be incomplete or not fully compatible. My questions: Has anyone successfully created a NetX Duo TCP Server project on the STM32H745/H755 Nucleo boards? Is there an official working example