Automotive and Transportation

Hi everyone, I've created a library and placed it in the directory /source/driver/. The library consists of the following files: source/driver/VN9d30Q100.h source/driver/VN9d30Q100.c The problem I'm encountering is that when I try to use a function from this library in my main.cpp file, I get an "undefined reference" error for the function VN9D30Q100_Init(). I've ensured that the header and source files are correctly written, and I believe the issue lies in how I'm compiling and linking these files in SPC5 Studio. Can anyone guide me on how to properly include these files in my project settings, or if there's something else I'm missing? Any help would be greatly appreciated! Thanks in advance,Lucifer

Dears,I didn't find firmware updater components on SPCx58N.Would you please suggest how to solve it  when develop bootloader app on SPC58N.Thanks a lot.

The error will appear when I configurate the module of AdcGroupDefinition, but the port and the hardware channel are configuarted correctly and conform. How can i solve this problem from the picture?   category : Errorproject : Cho6M_Gpt_rtm2description: Invalid XPath-expression for Attribute "INVALID" of node "/AUTOSAR/TOP-LEVEL-PACKAGES/Adc/ELEMENTS/Adc/AdcConfigSet/AdcConfigSet_0/AdcHwUnit/AdcHwUnit_0/AdcGroup/AdcGroup_0/AdcGroupDefinition/__5": (1818) No value found for object ""detailed : Invalid XPath-expression for Attribute "INVALID" of node "<a href="datamodel://Cho6M_Gpt_rtm2?/AUTOSAR/TOP-LEVEL-PACKAGES/Adc/ELEMENTS/Adc/AdcConfigSet/AdcConfigSet_0/AdcHwUnit/AdcHwUnit_0/AdcGroup/AdcGroup_0/AdcGroupDefinition/__5">/AUTOSAR/TOP-LEVEL-PACKAGES/Adc/ELEMENTS/Adc/AdcConfigSet/AdcConfigSet_0/AdcHwUnit/AdcHwUnit_0/AdcGroup/AdcGroup_0/AdcGroupDefinition/__5</a>": (1818) No value found for object ""id : 1803resource :path : /AUTOSAR/TOP-LEVEL-PACKAGES/Adc/ELEMENTS/Adc/A

Dears,When debugging SPC58N's network function. When I add printf function using RUN IO components.It always crash. I want to ask how to debug freeRTOS TCPIP protocol? which method to check how to get statistics info and etc.Thanks for help.

Hello, As shown in figure, I import a samples project, compile failure hint "make: * * * [components/spc560pxx_platform_component_rla/lib/RSC/rules. Mk: 164: elf] Error 1 "How do I solve it,T  

I want to test the SPC5-FLASHER program.When installing the program, you must register the serial number.How can I get a serial number assigned?Should I send the saved information by e-mail after recording the serial number request information during the installation process?Please tell me in detail how to register the serial number.

HelloI working with spc560p and I send or receive with SPI very good and had no problem, but if I want to send or receive more than 4 bytes (32bits) in one message (one chip select), what should I do? I used this format for send and receive: spi_lld_start(&SPID2, &spi_config_Achip);spi_lld_exchange(&SPID2, 4, txbuf, rxbuf);spi_lld_stop(&SPID2); Is there any sample in spc5studio wizard?

Very long awaited, but it is finally here!!!New AutoDevKit Studio release version 2.4.0 is available for free download www.st.com/autodevkitsw New features:- Multi-chain, multi-node and completed renovated BMS driver for L9963E named AEK-POW-BMSCHAIN- AEK-MCU-C4MINI - a new MCU discovery board with rich features: pin-pre-allocated, high-side drive, H-bridge drive for DC motor, dual LCD board connector, support for OpenOCD...- AEK-POW-BMSLV - a integrated BMS low voltage / aux power solution board including driver and basic application software, developed in collaboration with BeonD S.r.l.- Extended BMS GUI functions

We have bought SPC5-UDEBUG-TL license to be able to debug SPC58EE80 MCU.By description"Supports both SPC5-UDESTK standalone and the equivalent version embedded into Discovery board.Supports SPC5x MCUsSupports Multicore, eTPU and GTM debuggingIncludes FLASH programming capabilitySupport service provided through STMicroelectronics"Multicore and GTM debuging should work with this license but after registering license we got only one core debuging (unlimited by size of code). Multicore license we got after registration doesnt work and we did not got GTM license at all.Why is that?Michal Bedlivý

The mcu of SPC58 does not response the PORST reset. I knew one case that the mcu actives the reset escalation, but  MC_RGM.FRET.R and MC_RGM.DRET.R  have been set 0; I want know other possiable reason ?This problem confused me long time.  Thank you for give me some clue about this.

The chip I am using is SPC560P, please how can I do it to get the chip ID?

I am working on the development of SPC574K chip, but the debugger cannot connect with the chip successfully. When the chip is powered on, the crystal waveform is the first picture, which is normal. When I press the reset button or the connect button in the computer debugging software, the waveform of the crystal oscillator becomes the second picture. I want to know if the debugger's inability to connect to the chip is the reason, and why the reset makes the crystal oscillator work incorrectly.

Hi, I am trying out embedded virtualization with SR6X7, i have SR6X7 ZCU demo board with me. I am very new this this dev environment. could someone help me with embedded virtualization related docs.    Thanks in advance. Prabhu

Hello,I created a new project using default settings only to toggle an OUTPUT just to see the microcontroller performance.I monitored that outpup with an oscilloscope and I get only 4.17MHz.I am using a SPC58NH-DISP.Is that an expected output frequency or I am missing something?How much is the MIPS of SPC58NH microcontroller?PS.: it was used clock default settings.Best regards./* Inclusion of the main header files of all the imported components in the order specified in the application wizard. The file is generated automatically.*/ #include "components.h" /* * Application entry point. */ int main(void) { /* Initialization of all the imported components in the order specified in the application wizard. The function is generated automatically.*/ componentsInit(); /* Uncomment the below routine to Enable Interrupts. */ /* irqIsrEnable(); */ /* Application main loop.*/ for ( ; ; ) { pal_togglepad(PORT_LED1, LED1); } } 

Hello,The chip I am currently using is SPC560P50L3, I need a unique MCU ID for calculation, but I checked the MCU ID registers of the two chips and found that the information is the same, MIDR1=0x56042416, MIDR2=0xA8005011. is this normal?Or if there is any other unique ID for this chip, please let me know, Thanks. 

Dear community members, My board is AEK-MCU-C4MLIT1 and I have two problem: 1. When I use UDE STK to debug the example SPC58ECxx_RLA Test Application for Discovery, my board blink the test LEDs but when I connect the UART with my board (I've tried with both baud 9600 and 115200) but it displays non-readable symbols. Moreover, the debugger also display the message that "The instruction pointer could not be set to value 0x400a8030, the value reread is 0xFFF...". All the problems of this first question is depicted in the figure below:2. Then I moved to openOCD to test (already uninstalled Pls driver and Install UDESTK driver instead), I got an error message: "Illegal instruction fetched at address 0x400a8030. Memory corrupted or target reset?". Those pictures below reveal the error message and all the debug config setting that I config in my project:****************Driver installed and Debug config:  Any help would be very much appreciated.TH. 

Hello! I would like to ask what is the meaning of setting the Latched state option in the red box as shown in the following figure? I didn't see any specific definition or explanation related to this in the SPC58 reference manual? Can you tell me where to view its related content? Thank you.

Hello! I would like to ask what is the meaning of setting the Latched state option in the red box as shown in the following figure? I didn't see any specific definition or explanation related to this in the SPC58 reference manual? Can you tell me where to view its related content? Thank you.

May I use the onboard debugger on the SPC582B-DIS Discovery board to download debugging programs for the AEK-MOT-MR200G1 development board? Can you tell me which specific pins need to be connected? As shown in the following picture!

Hi, If you are getting this kind of error when you try to run your OpenOCD in AutoDevKit Studio 2.2.1: Then most probably you have not updated the search path of the config files. From main AutoDevKit menu, select Run > Debug Configurations   In the new window, select “GDB OpenOCD Debugging” drop down and the “SPC582Bxx_RLA AutoDevKit Studio generic” entry. On the right hand-side, please choose the tab “Debugger”     The issue is in the “Config options” field. The path present should be identical to your installation path. If you did not change anything from the installation default, the correct path should be:   C:\AutoDevKitStudio-2.2.1\openocd\scripts   If you installed under other path, please put the correct installation path. Repeat the same procedure for all the generic AutoDevKit Studio per type of microcontroller. To double check, you can look at the installation file and check for the missing .cfg file: In standard case, the installation path is

Hello, I want to do a boundary-scan test for a SIP module which uses ST Stellar Integration MCU SR6Gx series, how can I get its BSDL file?

I looked at the routine of SPC582B60E1! In the routine, pressing a button can use the callback function that interrupts the button to light up the LED light, but I have a question: how can I turn off the already lit LED light when I release the button? Can you give me some ideas or routines? I want to learn them! This is very important to me, thank you all big shots!

I want to debug my SPC563M64 board in SPC5studio. What should I do? I will go there to obtain support files for boards like SPC58NG 1>C:\SPC5Studio-6.0\openocd\scripts\board\spc58NG_dis.cfg2>C:\SPC5Studio-6.0\openocd\scripts\target\spc58ng.cfg3>C:\SPC5Studio-6.0\openocd\scripts\target\spc58.cfg where can I get these files for  SPC563M64 board just like the above files for  SPC58NG board!!!

Hello All, We have designed our own custom PCB using SPC582Bxxx, and we have assembled the controller and other circuit board. Now we would like to flash the our sample into custom device and test the same. For flashing the code we followed the UDESTK debugger connected to custom board JTAG debugger (Connected Custom JTAG and UDESTK JTAG). Using UDE software tool try to load the firmware on custom hardware, We could able to load firmware to board but the custom board after reset is not booting up.  Can any one help us how to load the firmware and bring up the custom hardware step by step.  Urgently need solution to this!!  Please get to us with your help Thank and RegardsRohit R

Is there a C program routine for the SPC560B series? I want to see SPI sending data and LIN sending data routines!