MEMS (sensors)

Posted on September 02, 2016 at 07:47There is  HTS221 driver version 1.0.0 on ST website.In this driver function HTS221_Activate reset bit HTS221_PD_MASK, and function HTS221_DeActivate set this bit. In datasheet written: ''PD: power down control (0: power-down mode; 1: active mode)''. Is it bug in driver? Where should be sent report?PS: I am set this bit, and evrithing well. #hts221-activate

Posted on August 26, 2016 at 23:37Hello, I am currently trying to do some initial noise analysis of LSM6DS3 using STEVAL-MKI160V1 adapter board and STEVAL-MKI109V2 mother board. The software that I am using for obtaining data is Unico GUI. The problem is that gyroscopes and accelerometers noise levels are higher than I expected by more than 2 orders of magnitude. Here is how I did:I first changed a couple of registers for low noise operation; CTRL1_XL was set to 10(hex), CTRL2_G was set to 10 (hex) for the lowest bandwidth of the low pass filters.High-performance bit was set to 0 for the high performance operation for both gyro and acc. This gives me very high noise outputs (see fig.1 & fig.2: Y-axis unit is deg/h an

Posted on August 18, 2016 at 12:12Hello, I am trying to use LIS2DS12's activity/inactivity functionality, settings according to https://my.st.com//content/ccc/resource/technical/document/application_note/69/fd/10/6c/42/38/4f/f2/DM00218428.pdf/files/DM00218428.pdf/jcr:content/translations/en.DM00218428.pdf (4.7). The WAKE_IA flag seems to be triggered alright (also tweaking the wake threshold seems fine) but the SLEEP_STATE (in status register or WAKE_UP_SRC register) flag doesn't seem to trigger. Did anybody have this problem before? Are there any specific settings I am missing maybe? #lis2ds12-inactivity

Posted on August 29, 2016 at 20:03We have an LIS2DH accelerometer on our board which is running linux 4.1 kernel connected by I2C and I'm trying to get it to work but have had no luck.Here is what I did:I got the linux driver from here: http://www.st.com/content/st_com/en/products/embedded-software/mems-and-sensors-software/drivers-for-mems/stsw-mems021.htmlAdded lis2dh.h to /include/linux/inputAdded lis2dh_acc.c to /drivers/input/miscAdded this to /drivers/input/misc/Makefile:obj-$(CONFIG_INPUT_LIS2DH)    += lis2dh_acc.oIn /drivers/input/misc/Kconfig+config INPUT_LIS2DH+    tristate ''STMicroelectronics

Posted on August 01, 2016 at 15:13Does anyone know if the LIS3DSH average samples when running at lower data rates? E.g. if the ODR is 100 Hz, will it sample at a higher rate and average the results (in order for example to reduce noise)? Or perhaps the nature of the method used to determine the acceleration in the first place will naturally average the data since the last sample?Thanks!Paul. #accelerometer #filter

Posted on March 17, 2016 at 16:34Hello,I  created my own PCB with iNEMO with USB communication, similar to STEVAL evaluation board. But I can't download any driver to establish communication - my comp shows message: ''...this computer malfunctioned, and Windows does not recognize it''!. I try with STSW-inemo001 (http://www.st.com/web/en/catalog/tools/PF257504#) but i can't download it.Please help me :) 

Posted on August 23, 2016 at 15:29Hi, I'd like to perform a SET/RESET procedure on the LSM303AGR magnetometer. As explained in the AN4825 pag. 17, if the user performs a single read, the bit OFF_CANC in CFG_REG_B_M must be set to '1' to invert the impulse polarity between a single read and the next one. Has this bit to be set high before the two consecutive readings or between the first read and the second one? #offset #reset #lsm303agr #set

Posted on February 18, 2016 at 06:53Hello,I just wonder where i can get a referece code for fusion of gyro+ACCfor LSM6DS3 / LSM9DS1 

Posted on August 16, 2016 at 12:39Hi! I'm trying to read Who Am I register and get 0x32 reply from the accel. Not sure what SPI mode to use, 3? I see on the scope: byte 0xF1 come out of master on MOSI, eight clock cycles on SCK and SS line go low, but nothing on MISO line. Shouldn't slave register bits come out by the mere fact that there is SCK (full-duplex) and SS is low? I'm not sure what is wrong, comments? Thanks. #4-wired-spi

Posted on August 16, 2016 at 19:32I am trying to produce 6 matched sensors. I have soldered them and I can query them via I2C, but their values are significantly off true air pressure. I know I'm supposed to use the RPDS_L and RPDS_H registers, but the data sheet does not clarify what that offset represents and what the units are. I thought at first that it was supposed to be multiples of 4096 like normal readings, but it doesn't appear to be so. Please clarify.Thanks. #lps25hb

Posted on August 15, 2016 at 17:56 I am trying to use the API for VL53L0x proximity sensor over one smt32F4Discovery developement board and I am not able to do it. The steps that I am doing are the following: In a Keil project that it compiles and links without problem, I am adding the source file of API, these files are separated in two folder: core and platform. I have added the files of two folders to project. After do it, I have also added related path to header file (*.h) in options for target --> C/C++ --> include paths. After do it, I try to build target files and there are several errors, output is the following:

Posted on June 13, 2016 at 14:41I could find the resolution of this sensor, 8 LSBs/DegC, but I couldn't find any information about how the absolute temperature is specified. Does anyone have more information about it? #ecompass #lsm303d #temperature

Posted on August 10, 2016 at 15:35Is there any FIT and/or reliability data available for the IIS2DH accelerometer?

Posted on July 04, 2014 at 15:19Hello,I got good results reading accelerometer data but the temperature register is about 36 (decimal), the datasheet mentions 8LSB/°C, 36/8 = 4.5°C, this is quite cold ;) Room temp is 24°C, the other sensors located near the LSM are indicating 28°C.What is the good conversion factor?

Posted on July 20, 2016 at 15:35The LIS3DSH was implemented into one of our systems and currently we are having an issue with the Temperature readings across multiple units in the same environment vary from one another up to 15ºC. Is there a way to calibrate the temperature on the LIS3DSH, or is it not recommended to use?The reason we are tracking temperature with it, over a temperature range the values change as described in the datasheet. And during our calibration process we are taking multiple temperature readings and normalizing the variance. Is it possible to ''reset'' the temperature in a controlled environment, or is this something where we would have to use a software offset? Also, those that show a large swing between actual temperature and readings, does this cause any adverse effects to the accelerometer measurements?

Posted on July 08, 2016 at 14:55Hi, We are looking for and 9 DOF sensor which should have good frequency response. I go through datasheet but was not able to fetch the frequency response details. Can you tell me the frequency responce of Part♯ LSM9DS1. As we wanted to have body motion + heart beat calculation through this Accelerometer. Waiting for your positive feedback soon. #lsm9ds1-frequency-response

Posted on August 10, 2016 at 16:45I have downloaded STM32F4-Discovery_FW_V1.1.0 firmware package and want to use the example of Audio Playback and Record on STM32F411.I am facing a lot of problems in building the project itself such as C:\CooCox\CoIDE\workspace\AudioTry6\Drivers\STM32_USB_Device_Library\Core\inc/usbd_def.h:27:23: fatal error: usbd_conf.h: No such file or directory and so on.Can somebody please help in organizing the project such as header files, source files, compiler options, linker options.Proper documentation is also not available. Links to either documents or direct help would be highly obliged. #usb-mic-stm32f4discovery #audio-processing

Posted on August 10, 2016 at 14:17Hi, We are looking for the product&sharpLSM9DS1, where it mentions sensitivity of 8.75mdps/LSB @ �250�/sec range. I would like to know the sensitivity at �125�/sec Range? Is it half of 8.75mdps? Is the range of �125�/sec configurable in Part&sharpLSM9DS1? #gyroscopes #lsm9ds1

Posted on August 09, 2016 at 00:05What is the recommended land pattern for LIS2HH12TR (LGA12)?

Posted on August 09, 2016 at 19:00I’d like to understand some basics, how to work with the device. I read the data from the chip and see it on terminal but I don’t understand how to practically use the data. Also when I use ACC data and when I use GYRO data? Is there some literature to read how to work with accelerometer? Somebook – accelerometerfordummies?

Posted on March 29, 2016 at 08:06Interested in purchasing the LSM6DS3 device. Studied the datasheet carefully, and there is no information on ADC resolution for the accelerometer and gyro. This is odd considering this is a key spec for any prospective buyer.  The datasheet does report temperature sensor resolution (12-bits), but for my project, this would be too low for the IMU readings. Can ST shed light on this? #resolution #adc #lsm6ds3 #imu

Posted on April 14, 2016 at 01:24Does anyone have information on the LAM6DS3 cross axis sensitivity? I cannot find this on the data sheet, when this is supposed to be a standard spec on other similar products. I contacted online support and they asked for an NDA??

Posted on April 14, 2016 at 09:52Hi everybody, I'm using LSM6DS3 and I need to know its resonance frequency. In the datasheet this information is not present. Thanks in advance #lsm6ds3-resonance

Posted on August 07, 2016 at 13:03Hello,1.according to section 2.11 Temperature sensor :should i read both OUT_TEMP_L (0Ch) & OUT_TEMP_H (0Dh) ?the data is stored only in OUT_TEMP_H (0Dh) ?2.the data i get using OUT_TEMP_H (0Dh) is too low (10C-13C), where the room temperature should be about 20C, am i reading the data wrong?RegardsAmir  

Posted on August 05, 2016 at 23:23Hi All,I am working with a LPS25HB sensor and am not able to get valid data out for the pressure or Temperature. Here is a register dump of my settings (tried 2 different settings):LPS25HB reg dump:0x08 , 0x0B0x09 , 0xA80x0A , 0x3F0x0F , 0xBD0x10 , 0x050x20 , 0x900x21 , 0x000x22 , 0x000x23 , 0x000x24 , 0x000x25 , 0x000x27 , 0x330x2E , 0xCF0x2F , 0x200x30 , 0x000x31 , 0x000x39 , 0x000x3A , 0x00LPS25HB reg dump:0x08 , 0xF00x09 , 0xA80x0A , 0x3F0x0F , 0xBD0x10 , 0x050x20 , 0xA40x21 , 0x000x22 , 0x000x23 , 0x000x24 , 0x000x25 , 0x000x27 , 0x330x2E , 0xCF0x2F , 0x200x30 , 0x000x31 , 0x000x39 , 0x000x3A , 0x00