MEMS (sensors)

Hi, I am, working with LIS2DH12 and I want to detect some variations of Z axis.I don't need to detect accelerations just variations of its current positions over my threshold. My current configuration is the following. CTRL1 (0x20) -> 0x17CTRL2 (0x21) -> 0x00CTRL3 (0x22) -> 0x40CTRL4 (0x23) -> 0x00CTRL5 (0x24) -> 0x08CTRL6 (0x25) -> 0x00 INT1_CFG (0x30) -> 0x20INT1_THS (0x32) -> 0x30INT1_DUR (0x33) -> 0x3C   Other registers set as default. What I want is to detect Z axis variations in case it has changed its position from (typically around 60) to something around +-14. I want it only to trigger the interrupt if it keeps this way more than 60 seconds that is why I set an ODR of 1. The problem is that my accelerometer is waking up my MCU every 60 seconds even when it is flat on the table and nothing is touching it. In case I read the axis, it gives me

Hello,I am developing a custom application that uses your ISM330BX IMU. I am communicating with the IMU using I2C. I checked that I can commuicate correctly with it by requesting the ID in the WHO_AM_I register and everytihng seems to work fine.The end goal is to get the LPSF block to work and output data to the fifo where it's going to be read by the main MCU. So far I tried following the info in the datasheet and the application note AN6109, but with little success. Every time I try to read the TAG of the data in the FIFO, the IMU always returns 0x02.Please find below (and attached) the two functions I use to set up the IMU and read from the FIFO. I am sure I might have missed something in the configuration, but I can't seem to figure out what.Thanks for the help.Kind regards,Marco// accel/gyro control #define CTRL1_XL 0x10 // XL ODR & mode :contentReference[oaicite:1]{index=1} #define

I’m trying to read the 3-component “game rotation” quaternion out of the LSM6DSV80X’s FIFO, but every time I pop a FIFO record I get three half-precision floats [x,y,z] where x is always zero and y,z look plausible. When I read the same fusion engine registers directly (not via FIFO), I get a full four-component quaternion [w,x,y,z] where x is nonzero—as expected. Ive connected the STEVAL-MKI247A to my ESP 32 via SPI with the following configuration // Define SPI pins #define CS_PIN 5 // Chip Select pin #define SCK_PIN 18 // SPI Clock pin #define INT_PIN 25 // Interrupt pin #define MOSI_PIN 23 // Master Out Slave In pin #define MISO_PIN 19 // Master In Slave Out pinWhat ive done: Enabled the SF-LP game rotation vector and timestamp in the embedded-function bank, thenConfigured FIFO streaming mode and set watermark = 1, and

Hello, I have a SensorTile.Box and I am playing with the "Expert View" mode on the ST BLE Sensor Classic app. I have created a useful custom application, which combines the output of different sensors on the board and transmits them over USB. When I save this application, a json file is created into the smartphone file system. I want to share this application with another user, but when I send her the file and she puts the file into the "Files->Internal Memory->Documents->SensorTile.box folder", she is not able to see any new app in the ST BLE Sensor Classic app. The only applications that can be seen on a device are the ones created on the same device. Is there any way to enable the share of the application profiles between different devices? Thanks, Francesco

Hi I'm working with the ISM330DHCXTR sensor and would like to know how long I should wait after applying power before the device is fully operational and ready to communicate (e.g., via I²C) Thanks Uri

Hi Team, We are using ASM330LHH IMU in our project. want to know if there are any special guidelines for placement of IMU on PCB. please let me know.   Regards, Jitendra

I'm using the LSM303AGR magnetometer with an STM32L4 via I2C + HAL. The built-in self-test works fine for X and Y, but Z-axis always fails — the delta (self-test vs. normal) is out of range.   Set UpSTM32L4, I2C, HAL driversMagnetometer config: 50 Hz, continuous modeSelf-test enabled via CFG_REG_C_M (0x62) = 0x1250 samples averaged before/after self-testDelays: 200ms (pre), 500ms (post self-test)     ProblemX/Y deltas: within 100–1000 LSB range → passZ delta: often too low or too high → fail    QuestionAre 100–1000 LSB valid self-test limits for Z?Is 50

Hi,I'm trying to get the SPI interface with the ISM330DHCX to work but it seems that the SDO pin can't reach logic high levels.The above has SCL in blue and SDO in red.CS in blue and SDO in red.

 Hello STM32 Community,I'm working with the LSM303AGR magnetometer/accelerometer sensor on an STM32L4 microcontroller. I'm trying to compute a tilt-compensated heading, based on the method described in ST's application note DT0058.However, I'm running into a problem: the heading value changes significantly when the sensor is tilted, even when the actual orientation toward magnetic north doesn't change. I expect the heading to stay consistent regardless of tilt, thanks to tilt compensation — but this is not happening.Below is the code I'm currently using to compute the heading:  uint8_t lsm303agr_heading_read(float* heading) {float magx_out, magy_out, magz_out;float accx_out, accy_out, accz_out;// Read sensor dataif (lsm303agr_acc_data_read(&accx_out, &accy_out, &accz_out, 10)

Hi all,I need to integrate the driver for the iis2mdc magnetometer (Github: https://github.com/STMicroelectronics/stm32-iis2mdc/tree/main) into my own project for a custom board (with STM32H7A3 and i2c3).  The code from the driver requires an additional hardware driver so that the magnetometer can be read/written to. However this interface functions are not included in the driver on Github. int32_t __weak iis2mdc_read_reg( ...) and int32_t __weak iis2mdc_write_reg(stmdev_ctx_t *ctx, uint8_t reg,uint8_t *data,uint16_t len){int32_t ret;ret = ctx->write_reg(ctx->handle, reg, data, len);return ret;} Is there any sample code available, which can be simply adjusted for the specific i2c interface? or do I

We've implemented an example program based on UM2220 using an lsm6dsox IMU sensor on an STM32U575 microcontroller. We're trying to use MotionFX for orientation calculation from 6 axis measurement, configured with accelerometer and gyro. The IMU sensor is configured to sample at 12.5Hz. Pitch and roll are extracted and printed to a terminalWhat we're seeing is that the output data is stable for a short period of time, however after an indeterminate period of time, pitch and roll become corrupted, spewing (seemingly) random data outWe'd really appreciate any assistance on why this may be happening! We've already tried doubling the stack size of the thread, with no luck

Hello STM32 community,I'm relatively new to STM32 development and I'm currently working with the I3G4250D Gyro Sensor on the STM32F411e-Discovery board. I've been using the stm32f411e_discovery_gyroscope.c file (BSP Drivers) provided by STM32Cube to interface with the sensor.I've managed to retrieve data from the sensor using the provided code snippet:BSP_GYRO_GetXYZ(gyro_data); X_val = gyro_data[0]; Y_val = gyro_data[1]; Z_val = gyro_data[2]; However, whenever I observe the output, the values keep varying even if the system is at rest. Also the output I'm getting seems to be raw data, and I'm not quite sure how to interpret it correctly. My understanding is that these values represent the raw sensor readings, but I'm unsure how to convert them into meaningful X, Y, and Z values.Could someone please provide guidance on how to properly interpret and convert these raw values into meanin

Hi,I have a i3g4250d sensor chip on our custom board with STM32G474 MCU.I have used the below driver github.com STMicroelectronics stm32-i3g4250dfor reading the sensor chip registers through SPI interfaceI am able to read "WHO_AM_I_ADDR" register without any issue that confirms my SPI interface is fine and communicating with sensor chip but when I read XYZ values I always get the same value irrespective of sensor position.My sensor init configurations areCTRL_REG1 = 0x3FCTRL_REG4 = 0x10When I read the STATUS_REG, the first read shows 0xFF and consecutive reads always shows 0x00What could be the problem.PS: I have a Accelero meter sensor chip lsm303agr on the same board configured with I2C interface which is working properly.Thank YouPrabhu M K

Hi,I'm working with the LIS2DW12 accelerometer in a low-power IoT application. The sensor is configured to wake the MCU via an interrupt on INT1, connected through a monostable multivibrator (Schmit trigger IC). The setup is designed so that a rising edge on INT1 triggers a reset of the MCU.Here’s the issue:When the MCU wakes from a previous interrupt (caused by actual motion), it starts reinitializing the LIS2DW12 — performing a soft reset and reconfiguring the registers into polling (standard) mode. Then, after some time in polling mode, if no motion is detected, the program switches the LIS2DW12 back into interrupt mode

Hi.i am having a STEVAL-IDP005V1, STEVAL-UKI001V1, 10-pin-IDP005V1 Cable, M12female connector.i am referring this document ( https://www.st.com/resource/en/product_presentation/steval-bfa001v1b_quick_start_guide.pdf ) i am not able to connect the board to my PC.  please anyone suggest me to do the analysis of accelerometeris that any clear document? Thank you  

Hi all, I have installed the LPS22HHTR on my custom circuit to communicate with a STM32F4x via I2C. I have pulled up the SCL (pin 2), SDA (pin 4), SA0 (pin 5), and CS (pin 6) lines to 3.3V via 4.7k resistors, grounded the two ground pins (8 and 9) and RES (pin 3). I have also provided a 100nF decoupling capacitor for the VDD and Vdd_IO pins and left INT_DRDY floating. My issue right now is that when i try to call on the device using its address (0b1011101 << 1) and the HAL_I2C_IsDeviceReady() function, I am not getting a response and a NACK is thrown (I2C_FLAG_ADDR = RESET and I2C_FLAG_AF = SET). I have double checked the configuration of the circuit several times and voltages at pins but I'm still not getting a response.  I would appreciate any help as to why this is happening or if I'm doing something wrong.

HiI am trying to run the STEVAL-IDP005V1-GUI.Current setup:STEVAL-IDP005V1-GUI - > STEVAL-IDP004V1->STEVAL-IDP005V1:I am unable to connect to the IDP004V1 dev kit from the GUI, the comms just gives an error suggesting to restart the GUI. I have tried re flashing the firmware with the 485 and USB binaries provided in en.stsw-io-link (https://www.st.com/content/st_com/en/products/embedded-software/evaluation-tool-software/stsw-io-link.html)I have tried both 485 and USB connections but it does not work. Please advise on how to get the demo's up and runningRegards

Hi, I am using STM32CubeMX to configure STM32CubeIDE project. I have Nucleo-U385RG-Q with MEMS X-Nucleo-IKS01A3. I am trying to read pressure sensor LPS22HH. According the X-Nucleo documentation the I2C default addresses for LPS22HH are: BA and B8. But the C code for the sensor defines BA and B8.Using the STM32CubeIDE project generated by STM32CubeMX I am not able to read sensor ID. The following code gives me an error. In the code I first define: stmdev_ctx_t dev_ctx; dev_ctx.write_reg = platform_write; dev_ctx.read_reg = platform_read; dev_ctx.mdelay = platform_delay; dev_ctx.handle = &SENSOR_BUS;Then use it: whoamI = 0; lps22hh_device_id_get(&dev_ctx, &whoamI);In STM32CubeMX i configured PINs PB6 and PB7 for I2C1. The sensor files "lps22hh_reg.*" I

Hi all,Could you please tell me if the temperature sensor of the LIS2DW12 is used to correct the acceleration sensor?Thanks all,

Has anyone tested the LIS2DE12TR accelerometer using lower input capacitance? I am interested in trying it out and possibly using it in an intrinsically safe design and the recommended 10uF capacitor is a deal breaker. Alternatively, does ST have a similar low power model that has lower capacitive requirements? 

HelloI would like to get the lis2mdl magnetometer data using the lsm6dsv second i2c line using the sensor hub.so far I get the accelerometer and gyroscope data via SPI and I want to add the magnetometer data.The code I have to configure the sensor hub and retrieve the data doesn't work. The i2c line doesn't even move (I checked with an oscilloscope)I checked with the example here  https://github.com/STMicroelectronics/STMems_Standard_C_drivers/blob/master/lsm6dsv_STdC/examples/lsm6dsv_sensor_hub.c#L504 but I have trouble understanding the codeI have a nucleo board l476RG not the demo board given in the example but since my spi communication works it shouldn't be a problem. I also have several lsm6dsv connected to my MCU but right now I try t

Hi I purchase a STEVAL MKBOXPro. It connects to phone and app fine but i'm having trouble to get the device connected to MEMS studio and Unicleo GUI  BLE Connection issue... 1. device manager detects STBOX but does not connect on MEMS studio and Unicleo GUI. I Problem with usbc connection.. 2. serial usbc sees COM9 with MEMBS studio but cannot connect to it when I hit connect button  Wondering what's causing the connection issue via bluetooth or via cable? I see a driver titled en.stsw-mkbox-bledk but i there is no exe button to install the driver.       

Hi,I'm developing a prototype based on an already existent product that contains an LSM303AGR, the goal is to install the device in a tower and detect when the tower is tilted or fallen, for this task the idea is to wake up the device via the interruption pin on the magnetometer as the device is battery powered and frequent checks on the status woud decrease the life span on the device too much. The main issue i'm facing is that my device seems too prone to false positives maybe caused by induced vibrations  by the wind on the tower, so far the best results are with the ODR to 1Hz, FS at 2g and adjusted the sensitivity acordingly but this is not an ideal sollution (each device has to be adjusted as the characteristics and eviroment of each tower is different and behaves differently), what is the right way to sense movement but filtering impacts? any sugetions about a good approach for detecting tilt and crash while being power efficient?

Hi all,Could you show me the temperature accuracy of LIS2DW12 ?Thanks all,

Hi,I’m encountering an issue with the LSM6DSOX IMU INT1 pin behavior during initialization. The expected behavior is for INT1 to remain LOW by default, including after a software reset. However, what I’m seeing is:After power-up or reset, the INT1 pin stays HIGH by default.It only transitions to the expected state (LOW) after the interrupt is configured and routed to INT1.I have checked the INT2, it is OK (default LOW)This is causing some unintended behavior during system startup, as other components relyin