MEMS (sensors)

Posted on March 28, 2014 at 03:06Anyone know the difference between  LIS3DE and LIS3DH?I need to make a testing jig to test a product uses LIS3DE, so I need to evaluate the self-test function ,but I cannot get any datasheet of LIS3DE.And there is no info about  LIS3DE on ST site.Any one have datasheet of LIS3DE?  Thank you. #lis3de

Posted on May 07, 2017 at 19:43this is the LIS3DSH  accelerometer on stm32f4discovery board0.12 mg/digit sensitivity it has how to calculate exact output with respect to unit of gis there any tutorial or documentation that  explain stuff.##lis3dsh #mems #accelerometer

Posted on September 12, 2016 at 09:05I am using HTS221 for humidity and temperature measurement. On reading the registers for temperature and converting as per the equation suggested, i get the correct temperature. but on reading the registers for humidity and converting as per the equation suggested, humidity obtained is not correct. the register values read are as follows: H0_T0_OUT = 9 H1_T0_OUT = -10540 H0_RH_X2 = 53 H1_RH_X2 = 132 when humidity is measured in a controlled environment with different known humidities, the HTS221 measured humidity varies +/- 5 % within the range 26.5 % to 66% humidity(which is calibrated range of sensor), but outside the range that is lower than 26.5% and higher than 66%  variation of 10 to 20% humidity is seen. kindly help to get the correct humidity. regards unnati

Posted on April 26, 2017 at 21:12Hi, I am using IIS328DQ in a new design. I want to set up an interrupt when the orientation is tilted away from Z-axis. So I set up INT1 as XHIE, XLIE, YHIE and YLIE. ZHIE and ZLIE are disabled.Here is the setup sequence according an AppNote:1. write CTRL_REG12. write CTRL_REG23. write CTRL_REG34. write CTRL_REG45. write Reference6. write INT1_THS7. write INT1_DUR8. write INT2_THS9. write INT2_DUR10. read HP_FILTER_RESET (if filter is enabled)11. write INT1_CFG12. write INT2_CFG13. write CTRL_REG5here is the reading of the sensor and all the registers:AX -0.039AY -0.063AZ 0.965WHO_AM_I : 0x32CTRL_REG1 : 0x27CTRL_REG2 : 0x08CTRL_REG3 : 0xC0CTRL_REG4 : 0x30

Posted on February 20, 2017 at 17:55 Hi, I have a problem to make interrupts (INT1 exactly) work with my LIS2DH12 Accelerometer. What I am trying to do is to make the int1 trigger when there is a Y-axis high event (or low event). I have setted all the required Registers for INT1 but it seems it is not working and I have even tried to look with an oscilloscope to see if it is doing something, but the results are still negative. I have read some posts before making this one but the answers weren't helpful for me. Can someone write down how they setted theirs interrupt registers to make them work correctly? Some additional information: 1- I don't need the HPCF so I have deactivated it (I think it is deactivated by default, if I remember correctly) 2- The REGs I have changed are: CTRL_REG3, CTRL_REG4, INT1_CFG, INT1_THS, INT1_DUR

Posted on January 19, 2016 at 09:16Hello everyone, I have a STM32F4-Discovery board with an integrated MP45DT02 MEMS mic, and I've bought also anothere mic (an MP34DT01), I would like to record at the same time from the 2 mics. By now I've captured audio from the integrated mic, and simulated the other mic with a RAM-stored pdm bitstream... Now I want to capture audio from the 2 mics at the same time... To do so I've to capture a bit both on the rising, both on the falling edge of the clock fed to the mics, but I don't know how to do... Up to now I've captured bits from the integrated mic just on one edge using the I2S... This is my I2S configuration: static void WaveRecorder_SPI_Init(uint32_t Freq) {   I2S_InitTypeDef I2S_InitStructure;   /* Enable the SPI clock */   RCC_APB1PeriphClockCmd(RCC_APB1Periph_SPI2,ENABLE);   /* SPI config

Posted on April 14, 2017 at 06:46Sensortile doesn't work without SWD connection.When I compiled and ran the demo application(BLE app), only it worked when the sensortile with cradle was connected to SWD which is from Nucleo board. When the board is detached from SWD and working with battery, the flashed image doesn't work. It means the board doesn't work standalone by using battery. I've checked that the battery is fully charged. Could anybody help ?

Posted on April 21, 2017 at 02:34When will ST release the VL53L1 User Manual ?I need the detailed technical manual with registers and different mode functions.

Posted on April 26, 2017 at 15:29Hi at all,I am using the BlueSTSDK Android App to receive data transfered via Bluetooth Low Energy by the STEVAL-STLKT01V1 SensorTile.I would like to detect accelerometer events as orientations, single taps, etc, with this app but I don't undestand how to unblock the 'Accelerometer Events' in the 'Feature list' activity.In the FeatureAccelerationEvent.java file is reported that I must call the following functions:- detectEvent()- onDetectableEventChange()but I don't know where and how I must call this functions.Is there anybody that can help me?Best regards,Tommaso#sensortile #bluestsdk

Posted on April 27, 2017 at 08:02Hi guys, I am using the BlueNRG GUI to play with the BlueNRG motherboard with daughter board on it. I set the GAP role to peripheral and observer, my question is, can I scan device and advertise data at the same time?

Posted on April 06, 2017 at 03:27Two questions.  I'm implementing the VL6180X sensor in a system that needs to detect presence of objects placed in a tray.   The objects are generally small glass vials with different colored caps.  Question 1:  In ambient office lighting, the objects are detected at expected distances if the colored caps face the detector.  If the glass bottom of the vial faces the detector, it appears as if the detected distance is the cap on the other side of the vial.  It does not seem to detect the glass bottom of the vial.   What would cause that and what is the solution to detect the glass bottom (note: the vial may be as close as 15mm and as much as 70mm from the sensor- there is no cover glass on the sensor).Question 2: After the object is placed and the distance detected, a cover door is closed which put

Posted on February 23, 2017 at 02:39Hi, I have a project that uses LIS3DH. I just noticed an update at the Datasheet and now there is a  CTRL_REG0 that I can disable the SA0 pull-up. Is this available since the beginning or just on new batches of the device?

Posted on April 24, 2017 at 15:40When I transition from a powerdown state to any of the ODR's in FIFO mode I get initial values (first 1 or 2 sample sets) in the FIFO buffer that are very erratic. Should there be a period of time after transitioning out of a powerdown mode before the FIFO is enabled?

Posted on April 24, 2017 at 15:02Hi, I've VL53L0x Satellites board and according to datasheet page 21, section 3.2http://www.st.com/content/ccc/resource/technical/document/datasheet/group3/b2/1e/33/77/c6/92/47/6b/DM00279086/files/DM00279086.pdf/jcr:content/translations/en.DM00279086.pdf I should be able to read register 0xC0 for i2c validation. I've 5V, gnd, SDA and SCL hooked up to my AArdvark total phase i2c analyzer. I also use Aardvark activity board to make sure i2c is working properly and it is working properly. However, when I hook it up to satellite board, I was not able to read anything. Is there I need to do to get it initialized.

Posted on June 28, 2016 at 11:15I'm trying to use UNICO with an eval board that contains the LPS22HB sensor.  I cannot find this device under their Environmental sensors device list.  Is there a way to add it to the list, or to update UNICO?  I'm using version 4.2.0.0.  Is there an updated version that has the LPS22HB pressure sensor in it? #lps22hb-sensor-non-recognition #lps22hb-unico

Posted on April 22, 2017 at 12:21I am currently trying to interface LIS2DE12 Mems Accelerometer in our project.The datasheet is all about hints more than explanationsI scrolled around datasheet and couldn't find the meaning for AOI Function interrupt,  IA_1  & IA_2 InterruptCouldn't even guess these things.What are those interrupts mean ?And one more doubt :There are interrupts for new data available in x,y and z axisWhat is that new data actually mean ?I think new data will be available in the rate of ODR (Output Data rate). So why there is a separate interrupt needed for that ?Or will the interrupt occurs when a new data is available which crosses a threshold difference of the old data ? ----------------------------------------------My Requirement :* Activity detection (Rest to

Posted on December 22, 2016 at 23:04HiI'm using multiple vl6180x devices and want them to work more quick.However, when the second device starts in pre-calibration time of first device, the range data looks wrong.When I set the interval more than 4ms between two devices, their range data looks correct.So, I guess that in the case that two devices work simultaneously in their pre-calibration time, the interference occurs.Then, I would like to ask whether I make pre-calibration time shorter than 4.3ms or skip pre-calibration phase.I read the data sheet of vl6180X and found the pre-calibration time is fixed.However, I want absolutely multiple vl6180x devices to work simultaneously.Otherwise, I want them to work more quickly (less than 4ms interval). Is it possible?Best regardsIshikawa#vl6180 #multiple-vl6180x #vl6180x

Posted on April 21, 2017 at 17:25I tried to read the default I2C password (address 2304 with E2 = 1) that should be 0000 0000h whilst I found FFFF FFFFh. For verification I also tried to read the other System parameter sector and the returned values are matching what explained into the datasheet.I haven't implemented the function to change the password so I'm pretty sure it should be the one sent out by factory.BR,Giorgio Cancelli#m24lr04e-r

Posted on March 24, 2017 at 11:48What is the meaningful of 'SPI only write' SIM bit of CTRL_REG3_M (22h) register?How magnetometer values can be read if SPI is in write only mode?

Posted on April 19, 2017 at 14:25Hi all,I'm trying to interface a LSM303AGR, to get the magnetometer and accelerometer values in I2C.The component is responding well to whoami requests (both compass and magnetometer parts), I manage to get mag values but the accelerometer values seems to be stuck.Here are my init parameters:    /* REBOOT ACCELEROMETER MEMORY CONTENT */    I2C_Write_reg(I2C2,I2C_LSM3_ACC_ADRESS << 1,I2C_LSM3_CTRL_REG5_A,0x80);    RTC_wait_ms(6);    /* REBOOT MAGNETOMETER MEMORY CONTENT */    I2C_Write_reg(I2C2,I2C_LSM3_MAG_ADRESS <&l

Posted on April 19, 2017 at 23:28I'm using the LSM6DS3 to control a gimbal with a camera on it, and I'm noticing that my control is suffering due to delay in the system. I have configured the LSM6DS3 for an output datarate of 208Hz, with the fifo in bypass mode and I'm also sampling the sensor at 208Hz. However when I measure the delta between a physical input to the camera and the observable difference in the LSM6DS3 readings, I see about 20ms of delay. When I increase the datarate of the sensor to 833Hz, the delay is reduced to roughly 10ms, but this delay still seems rather large.Is there any spec on the bandwidth/ delay/ latency of this sensor? What can I do to get the absolute latest readings from it?#lsm6ds3

Posted on April 13, 2017 at 13:39Totally new to ST accelerometers, I can see that they're grouped into what look like three 'families' -- nano, pico and femto. Is there a short explanation of the differences between those three families? A link to a page explaining that would be just ducky, thanks.rday

Posted on October 18, 2016 at 09:49Hi!The HTS221 sensor and LPS25HB pressure sensor are together in the development board. The temperature difference between the output of the two sensors too high. HTS221 temperature value is close to the actual temperature, LPS25HB outputs 5~10'C lower than that at room temperature environment.The output temperature of the two devices is a 2's complement form of the same.I'm not sure about the cause of this difference is.Please give advice on this matter.Best regards.Kwon #lps25hb

Posted on April 18, 2017 at 07:48I'm using an LIS3DH accelerometer. It is configuring properly and returning valid data when manually read at a fixed interval. Now I'm trying to switch to the use of its XYZDA signal that is emitted on INT1.I have all other interrupts on INT1 disabled, and I'm enabling XYZDA by setting bit 4 of CTRL_REG3. If I clear the bit, INT1 stays inactive, and if I set the bit, INT1 starts showing activity, so I'm confident I'm setting the bit I think I am {grin}.A scope shows that INT1 goes active at ODR intervals, as expected. The problem is INT1 resetting to inactive. Section 3.1.2 of the LIS3DH's app note says 'the interrupt is reset when the higher part of the data of all the enabled channels has been read (29h, 2Bh, 2Dh)'. This seems clear enough... read the MSB of all three axes and INT1 should be cleared.However, what happens instead is that INT1 clears at variable times, often many tens of milliseconds

Posted on April 13, 2017 at 01:08With a 2g scale sampling @25Hz the FIFO fills with data and I am reading the contents up to the watermark. HR and LPen are disabled.With the Z-Axis pointing toward earth I get the following data for the X-Axis using the H and L bytes:DATX=128DATX=128DATX=128DATX=-64DATX=192DATX=-128DATX=-64DATX=0...First, why are the values multiples of 32? Second, why the variability when the chip is still and not moving? I have been using the LIS3DSH for a couple years now so this IIS2DH is a real downgrade for sure, but I must be missing something. I have read over the manual several times now and can't find my issue. -AP