STM32 MCUs Boards and hardware tools

Hi im having nucleo h755 board with me, in that usb port section i can't understand, if i connect through usb cable, the board will power it or not. i tried, it not powering the board.And how the circuit will work when fault occurs. and it is possible to power the board when connected to usb cableplease find the atttached image of nucleo h755 usb port schematics. regards,srinath

I am using the Nucleo-N657X0 for a project. I was in the middle debugging my project and unplugged my board. Now I am unable to connect to my board for debugging or programming in the IDE. I can however connect to the board in CubeProgramming. How do I get my board to connect for debugging and programming again in IDE? I have the boot pins set to the following (just in case this helps):BOOT0 = 0BOOT1 = 1This is what the console outputs when trying to connect. Failed to bind to port 61235, error code -1: No errorFailure starting SWV server on TCP port: 61235Failed to bind to port 61234, error code -1: No errorFailure starting GDB server: TCP port 61234 not available.Shutting down...Exit. Thanks

stlink-V3PWR can't support third-party ARM chips(swd download program)?  stlink-V2 Very perfect。stlink-V2 support third-party ARM chips。  Please update the firmware. thank you . 

Hello ST Community, I have designed a custom PCB using the STM32H750XBH6 microcontroller. After soldering the chip to the PCB, I attempted to connect it via ST-LINK using the standard SWD interface, but the device is not being detected. I have verified the following points: VDD, VDDA, and VDD_LDO are supplied with 3.3V VSS and VSSA are connected to GND PDR_ON is tied to VDD (as recommended) VCAP1 and VCAP2 are connected to 2.2µF capacitors to GND BOOT0 is pulled down to GND SWDIO, SWCLK, and NRST are correctly connected to the ST-LINK Voltages and connections are checked with a multimeter — all seem fine

Hi everyone,I am currently working with the NUCLEO-H7S3L8 board and using STM32CubeMX version 6.14.1 to generate code. I've kept everything at default settings and only added pins to toggle LEDs for testing. However, when I try to debug the code, I run into an issue where the boot subproject gets stuck at the SCB_EnableDCache(); function for a while, before eventually jumping to Error_Handler(void).I haven’t modified anything else in the generated code, so I'm wondering if there’s a configuration setting I may have missed or something I need to tweak in order to resolve this issue.Has anyone encountered this behavior or know what steps I should take to fix it?Thanks in advance for your help!

 Subject: Request for Feedback on STM32F405RGT6 Minimalistic Development Board SchematicHi everyone,I'm currently working on building a minimalistic development board based on the STM32F405RGT6 chip. Since I couldn't get access to a Discovery or Nucleo board for this particular MCU, I decided to design my own.I'm still quite new to PCB design and only have a basic understanding so far. With limited knowledge and some reference from other designs, I managed to put together a schematic for the board. My primary goal is to upload firmware using DFU (Device Firmware Upgrade) mode.Before I proceed further, I’d really appreciate it if someone could review my schematic, point out any mistakes, and suggest improvements. I want to make sure everything is correct before moving to the PCB layout stage.Thank you in advance for your support!

i am using Riverdi RVT50HQSNWC01-B - STM32 EMBEDDED 5.0" DISPLAY in the display have inbuild Micro Controller Unit STM32U5G9NJH6Q.I tested the internal loopback and external loopback in this and it works fine but the normal mode is not working.Can you tell me what I need to do to make CAN FD normal mode work?and i have RVT121HVSNWC00-B - STM32 EMBEDDED 12.1" DISPLAY in the display have inbuild Micro Controller Unit STM32H757XIH6. so i need to CAN FD communicate STM32H757XIH6 to STM32U5G9NJH6Q controller.and we have two Riverdi RVT50HQSNWC01-B - STM32 EMBEDDED 5.0" DISPLAY in the display have inbuild Micro Controller Unit STM32U5G9NJH6Q. so first i try this two. that project file i attached so please the how to fix it.

STLINK V3 stopped working after upgrade. Red light is flashing. Device manager - Unknown USB Device. NUCLO and DISCOVERY with ST-Link2 are still working! Installing dpinst_amd64.exe not help.

Hi, Im having issues programming with the STLINK-V3SET on the STM32G474E-EVAL1 board with the tag connector(CN15) I get the following output when using the STM32CubeProgrammer13:09:01 : UR connection mode is defined with the HWrst reset mode13:09:01 : UR connection mode is defined with the HWrst reset mode13:09:01 : ST-LINK SN : 0039002B323451083630353213:09:01 : ST-LINK FW : V3J16M8B5S113:09:01 : Board : STLINK-V3SET13:09:01 : Voltage : 0.64V13:09:01 : Error: Unable to get core ID13:09:01 : Error: No STM32 target found! If your product embeds Debug Authentication, please perform a discovery using Debug AuthenticationAnd with programming with the IDE I get the following output Starting server with the following options:Persistent Mode : DisabledLogFile Name : C:\Users\aiglesias\Documents\test\Debug\st-link_gdbserver_log.txtLoggin

 Hello,I want to interface NHD-2.7-12864WDW3 OLED display with STM32H755 Nucleo and show some data in display-4 wire SPI-. I had connected all OLED pins to STM32 correctly and than tried to flash this code (that I've attached). But i did not get any output, OLED display did not even glow.I dont know where i am doing wrong, can you help me

I have stm32u5g9j-dk1 demo board. The LCD on it is J025F1CN0201W. But I am not able to find its data sheet or technical spec. May I have copy of it? Thank you. Kelly

I want to interface  NHD-2.7-12864WDW3 OLED display having SSD1322 controller with STM32F407G-DISC1.I am doing 3 wire SPI Communication, So i have connected all 20 PINS as follows:Pin1 ---> GNDPin2 ---> 3VPin3 ---> NC (No connection)Pin4 ---> PD9 (DC; GPIO_Output, assigned by cubeide) 

Hello .. Anyone can kindly advise where to download STM32F446ZE nucleo board schematic diagram. thx. 

Same: Target unknown error 32From the STMCubeIDESTM32CubeIDEVersion: 1.19.0Build: 25607_20250703_0907 (UTC)OS: Windows 11, v.10.0, x86_64 / win32Java vendor: Eclipse AdoptiumJava runtime version: 21.0.3+9-LTSJava version: 21.0.3Flashing a Nucleo N6Example Uart Console AppDid do the stlink firmware update, seemed to work.Flashing other boards works...

I have Nucelo-F303RE but needed easy access to the pins and needed to keep track of their names, but so just sharing a pic of what I came up with: Note you will need two socket headers with long pins of size at least 1x19 (in my case I used 2x20 cause I didn't have any 1x19 ones) that will access the outer columns. The pins unfortunately don't quite line up perfectly into the breadboard like this, so the socket headers are slightly non-vertical, but at least it works and gets access to outer columns over the breadboard.  And make sure you have a good fine-point pen for writing the pin names small and legibly onto the sticker or tape.  I wish they included such

I am developing a system composed of multiple STM32-based boards organized in alayered architecture: six slave layers each with a nucelo f439zi perform data acquisition, while one master board still f439zi, manages synchronization and orchestration thought the timer signal, PWM output of channel 1 of TIM1 at 400khz: this signal is used to trigger the ADC of different MCU to have a synchronization across all system of sampling time.The power supply is Distributed centrally by the Master Layer with a DCDC converter (or lab dc power supply) through ribbon connectors, total length of 80cm :i actually have 3 power supply over a 16 pin ribbon cable: 3.3V, 5V, 29.5V.The PWM generated by the master layer has a separate Ribbon connector 14wires : 1 wire for PWM signal, 13wires to GND, that reaches all the 6 slaves boards Nucleo are connected to the 5V rail in parallel, and after connecting each layer of the system,

Hello all, I've been using my STLINK V3 successfully for around half a year until it suddenly stopped working from one day to the next. When connecting it to the PC (no target) the green light is on and the red light if flashing forever. It does not turn orange like described in the manual, neither switch to constant red, as it was before. Windows it not recognizing it as an USB device at all (the first two times it showed something like unknown device, but never again since).My setup works with another STLINK V3 so I would exclude cable, USB port issues or similar.  Any idea, what the issue here is, or how to fix it?

Hello, I wanted to use these screen from aliexpress : It uses MIPI DSI and Touch Screen. I have no idea yet if touch pins are doubled on both sides. But I don't know how to connect these pins in the devboard which looks like that on the back ... 

Hello, I have been trying various methods of installing the ST-Link USB drivers on my Windows 11 Laptop, with absolutely no success. Here is the output I see when I try to run the installation batch file from the stsw-link009 download:When I plug in my nucleo board, this is what I see in the device manager:When I open the properties on the ST-Link device, it (obviously) says that the drivers are not installed. Needless to say, if I try to run a program form the

i whant to know if the B-CAMS-OMV is compatible with the 32F746GDISCOVERY, NUCLEO-N657X0-Q, and the STM32N6570-DK?because i why didn't I find the specific connector data of the 3 kits regarding the camera,And I want to know this one camera B-CAMS-OMV is good for me for the 3 different kits?

I ordered https://www.st.com/en/evaluation-tools/nucleo-n657x0-q.html and it mentions Camera module FPC. But I cannot find any information on which protocol it uses for this camera connection. For example, can I use https://www.st.com/en/evaluation-tools/steval-56g3mai.html#overview with the MIPI-CSI2 protocol? Where could I find more information about the supported camera's for the STM32N6 evaluation board?

Hey all,I've spent a fair amount of time trying to make a DTMF tone generator using an STM32F411VE board I got as a gift. The board comes with a CS43L22 DAC chip that can be accessed by the STM32F411 through I2C and I2S. My rationale is as follows:1) Using the reference manual and CS43L22 datasheet, write a simple I2C driver to initialize the DAC, send commands, etc.2) Using the reference manual and CS43L22 datasheet, next write a simple I2S driver to send audio data via DMA to the DAC.3) Use the FPU to calculate samples of the desired DTMF tone and use a circular buffer/DMA to write those samples to the DAC with a frequency of 48 kHz.Seemed simple enough to me, and if I thought that if I followed the two aforementioned documents closely, I should be able to knock it out in a couple of days (I'm still a bit of a beginner with bare-metal programming).That was not the case :) the biggest hurdle I've hit so far involves the CS43L22 DAC. I

HiI just received a STLink-V3SET from www.tme.eu.It does not appear to be a clone in any way.Upon trying to update it with StLinkUpgade 3.16.8 it shows its ST-Link ID but claims that the current firmware is V0J0S0 and at the bottom it says "Unknown firmware type. Don't know how to upgrade." Have I received a faulty device?Best regardsMartin

I'm working on a project requiring me to save a frame captured by a camera to an SD Card. I'm using SPI to do this. I am able to save the image from an OV5640 camera to sram in a buffer using DMA, where the size is more than 300,000 bytes. I am able to save a text file to the card if I have something short like "Hello World," but when I try to save the buffer containing the frame, error code 1 is returned signaling a hard fault. Also, the errors aren't always the same, sometimes the close and un-mounting steps end in a hard fault too, but that usually goes away after rerunning the code. I am using SD Card drivers from KiwiH here. I added debug print statements throughout the f_write function in ff.c and I saw that the line that is causing the error is the here (line ~3691):if (disk_write(fs->drv, wbuff, sect, cc) != RES_OK) ABO

What is the lens used on the B-CAMS-OMV kit?  Or, what is the field of view?  or, what is the focal length?