STM32 MCUs Products

I try to control position of servo with potentiometer. I get data pot using DMA method and than i convert these data PWM signal pulse width due to control servo, but it is not working i really don't understand why does it working, servo motor is not working but i read pot in live extension and i convert this pot data which is i exactly want but I CAN NOT GET PWM OUTPUT.   What could I be missing in the clock configuration settings? i use STM32F103C6T6A and timerclocks 48MHz i set timer prescalar 959 and counter period is 999. and ADC prescalar is 12.  this is code: while

How to open the STSW-IO-LINK evaluation firmware in the STM32CubeMX development platform? STSW-IO-Link is downloaded and extracted. The *.ioc file seems to be missing in the STSW-IO-LINK firmware package!

Hello,I am reading AN2606 and I am wondering if I am interpreting the document correctly. Is table 113 suggesting that the FDCAN bootloader is only available on pins PH13 & PH14 in the STM32H75 series? Since these pins do not exist on the 100 pin packages of the part, is it not possible to use the FDCAN bootloader on 100 pin packages?Thanks.

On Cubex Generated code, we added Virtual Com Port code.But the code is going to Hard fault handler in USB_ActivateEndpoint.  HAL_StatusTypeDef USB_ActivateEndpoint(USB_DRD_TypeDef *USBx, USB_DRD_EPTypeDef *ep){HAL_StatusTypeDef ret = HAL_OK;uint32_t wEpRegVal;wEpRegVal = PCD_GET_ENDPOINT(USBx, ep->num) & USB_EP_T_MASK;  Please can you suggest any thing is wrong.

Hi Team,I am currently working with the STM32G0B1CET6 microcontroller and using two Abracon crystal parts, ABL-8.000MHZ-B2 and AB38T-32.768KHZ-B. However, I am encountering issues with the crystal when I use heavy ( like code more than 50% ram & flash of this STM-g0) percent of my code in STM. Attached is the schematic for your reference.,  Thank you,Ashu Tamar

Question seems simple enough, but i cant find any information on this in the datasheet or refman:When i put the mcu in stop-mode using the hal driver, i call this function:HAL_PWR_EnterSTOPMode(PWR_MAINREGULATOR_ON, PWR_STOPENTRY_WFI);The first parameter of this function can be either PWR_MAINREGULATOR_ON or PWR_LOWPOWERREGULATOR_ON.The function seems to set the LPDS bit in PWR_CR register based on that parameter. According to the reference manual, this means:0: Voltage regulator on during Stop mode.1: Low-power Voltage regulator on during Stop mode.That is not enough information to decide what i should go with for my application."Low-power Voltage regulator" implies that the MCU consumes less power in this mode. How much less? And what is the down-side of using the Low-power Voltage regulator?

When booting up STM32Cube for the first time I get the error "A 'stm32Cube Updater' (or another 'STM32CubeMX') software is downloading to the repository folder Please wait for the download to complete and retry" However, no software is open/ downloading anything and I have waited 30 minutes. When trying to open up the MCU selector it is stuck loading on most buttons as well.  

I think i correctly setted up the slave adress on 0x70 with the configuration window.Below my script on the Raspberry Pi. #include "main.h" #include "string.h" #include "stdio.h"       I2C_HandleTypeDef hi2c1;   UART_HandleTypeDef huart2;     void SystemClock_Config(void); static void MX_GPIO_Init(void); static void MX_USART2_UART_Init(void); static void MX_I2C1_Init(void);     int main(void) {     HAL_Init();   char msg[10]; int buf[12];   SystemClock_Config();     MX_GPIO_Init(); MX_USART2_UART_Init(); MX_I2C1_Init();   while (1) { if( HAL_I2C_Slave_Receive(&hi2c1, (uint8_t*)msg, 2, HAL_MAX_DELAY) != HAL_OK)

Hello,I wonder if my STM32H7BI3-DK has a wi-fi module? It looks empty on the circuit board?On pictures of the board I could find on internet, there's supposed to be green card: How can I add a wi-fi module to my STM32H7BI3-DK?  

Controller: STM32G431VBT6Libraries: CMSISCompiler: arm-none-eabi-gcc version 13.2.1Code Optimization: OPT = -OsAfter code optimization MCU hangs, depending on code constellation. It hangs in ADC initialization. ... system_clock_init(); timer_init(); ADC_init(); USART_init(); ...  void clock_init(void) { // configure wait states (2.7 V .. 3.6 V @ 170 MHz) FLASH->ACR = (FLASH->ACR & ~FLASH_ACR_LATENCY) | FLASH_ACR_LATENCY_4WS; // enable and reset instruction cache FLASH->ACR |= FLASH_ACR_ICEN | FLASH_ACR_ICRST; // debug software enable FLASH->ACR |= FLASH_ACR_DBG_SWEN; // start crystal oscillator (HSE) RCC->CR |= RCC_CR_HSEON; // switch on crystal oscillator while((RCC->CR & RCC_CR_HSERDY) == 0); RCC->PLLCFGR = (8 << RCC_PLLCFGR_PLLPDIV_Pos); // P main PLLP division fac

I am using my custom board PCB with STM32F103C8T6 MCU. I want to give a PWM signal to PB1 pin & want to set PB2 pin to HIGH. While giving the PWM to PB1, although I set PB2 pin status as HIGH, when I measure the voltage of PB2 pin it shows '0V' value. I am using keil uvision to developed the firmware. How do I solve this problem? Can I set PB2 to HIGH while giving a PWM to PB1? 

Hello,I need to implement delay macro, lasting just a few cycles.As the delay is so small I would not like to use TIMs o DWT.On Texas Instruments DSPs, I was used to implement this nanoseconds delays, using NOP() instructions.Unfortunately, as also written in STM32 Programming Manual this is not a good pattern on Cortex processors.On a previous post, related to another issue, I was suggested to use Data Memory Barrier (DMB), Data Synchronization Barrier (DSB), and Instruction Synchronization Barrier (ISB) instructions, instead of NOPs.How can I use this instructions, to implement a few cycles delay macro?Regards,Carlo

Hello everybody,having a dual-bank Flash memory into an STM32G0 MCU, what could be the best approach to update the user application ?By using the swap feature or by making a copy of the new user app from Bank 2 to Bank 1 (by using a bootloader)?Thanks

Hi, ST community.I'm trying to drive a motor using Nucleo-H503RB.At that time, I want to use DAC pin to watch variables, but I have problem of DAC.<Detail>To use the DAC, I set the PA5 to the DAC in Motor Workbench.I confirmed that when the DAC is set, an offset occurs in ADC values such as bus voltage obtained by PA1 and inverter temperature obtained by PC2.This problem occurs even if the motor or inverter is not connected(Only Nucleo-H503RB).I confirmed two Nucleo-H503RB,but same problem occured.Why does this problem occur?When offset occurs, over voltage error occurs and the motor cannot be rotated.I'll send Workbench files with and without DAC enabled.The software I use to generate F/W is Motor Workbench 6.2.1, EWARM V8(but debug in V9), CubeMX6.10.0, STM32Cube_FW_H5_V1.1.1 and control motor by Motor pilot 6.2.1.Please tell me solution.And,STM32Cube_FW_H5_V1.1.1 doesn't have Nucleo-H503RB DAC e

Hello ST Community.I am currently engaged in a project that involves the use of the I2S bus with the STM32WL55JC1 microcontroller. I’ve been working within the Arduino IDE environment and have come to understand that there isn’t a readily available library for the easy implementation of this bus. From my research, it seems that creating a custom library might be necessary. However, before I proceed down this path, I wanted to reach out to the community to ask if there is a simpler method to utilize the I2S bus on the Arduino IDE with the STM32WL55JC1 Nucleo board. Any guidance or suggestions would be greatly appreciated as it would significantly streamline the development process. Thank you in advance for your assistance!       

Good afternoon community,I am trying to implement the Input Encoder in STM32F407G Discovery board.I implement all things, but I am not able to generate desired the output from the board.I get counter/count/position value as zero.   Can you please help me to implement the Input encoder?Here is code for your reference, if any reference code you have then please provide me.Thank you.

Hi,I have configured the Nucleo-L476RG to write to a 64GB exFat Micro SD Card in 4-bit mode using DMA.This appears to work correctly once I navigate around the still present library errors which prevent you from initialising in SDMMC 4-bit mode. You must initialise in 1-bit mode and then change to 4-bit mode as described in https://community.st.com/t5/stm32cubemx-mcus/sdio-interface-not-working-in-4bits-with-stm32f4-firmware/td-p/591776.My issue is that when I scope the data lines D0, D1, D2 and D3 the only line which toggles is D0. The timing between 1-bit and 4-bit mode has also been raised in https://community.st.com/t5/stm32-mcus-products/sd-card-read-write-

Please find the image for the reference.Falling time of digital signals should in nano second, but here its almost taking 42usec. I have configured GPIO mode as Alternating Push and Pull, Pull down.let me know how to reduce the falling time.

Dose someone know if it is possible to use TM3 in Encoder Mode. And also get the internal detected counts for each input. I use TIM3 channel 1 and 2 for the encoder.many thanks

Hello dear Community,As an emerging engineer(newbie steps 1st yr into mbed) with a MEDICAL company startup transitioning into product development, my first project:face_with_rolling_eyes: involves designing a 12-lead ECG patient monitor. The initial attempt, led by a former employee with an Android background, utilized an Android board and android display but failed due to the lack of a real-time OS and Android API limitations. This experience has led us to consider an embedded approach, diverging from custom dedicated boards commonly used in the industry.How to approach custom board?Our device features a 10.1-inch TFT display (1280x720), supports ECG printing, NIBP, SpO2, temperature monitoring, real-time 12-lead ECG processing, connects to ECG module via UART, and interfaces with an 8-inch thermal printer.In aiming to use the microcontroller efficiently and to avoid the previous attempt on  overcapacity is

I'm working on a custom board with a F446RET6 and testing through some code bits. I've been able to successfully test that the board programs and functions with a led-blink style program. My problem is that I'm attempting to use CAN2; I'm trying to test via loopback but I'm having issues getting any type of IRQ for a receive. I feel like its something basic I'm missing here but after reading through some other posts I'm either brain-dead or missing something.currently using the HSI clock but I wouldn't think that would matter for loopback testing (understand for the "real" thing would be best to use the HSE).RX GPIO is set to pull-upVerified (after looking at some old posts using an older version of Cube) that the CAN1 clock is being initializedAlso I understand that the "CAN2" device is really the "slave" to CAN1. I've got my slave start for the filter set to 14 to split everything half and half and just arbitrarily chose bank 15:&n

Hello, i am trying to interface TI's ADS8910 (18bit SAR ADC) to an STM32F730 via normal SPI, since i am unsure whether QSPI will work.I want to achieve the full 18 bit @1MSa, which is possible when working with 54MHz (/2 APB2 prescaler on the F730 which runs at full speed - 216MHz) and the ADC's zone 2 transfer. The HAL implementation of dma transfer is way to slow between consecutive readouts and thus gets stuck "busy" and "locked" forever after the first readout. Therefore i am currently trying to write everything myself. My question is regarding the SPI CR2 register, bits 6 & 7 (RXNEIE and TXEIE):Will the DMA requests, mentioned in Bits 0 & 1 (RXDMAEN and TXDMAEN) still be generated when the interrupts are masked?I don't want my program to be interrupted more than neccessary. the flow should be :F7 gets an interrupt that signals that the ADC has finis

Hello,I'm working on a cutom made board controlled by an STM32F303ZET, I figured out that I forgot to pull up D+ for USB communication, even doing it externally keep showing me this error. I tried to pull up the D+ using 3.3V directly and also by pulling another pin HIGH. How can I resolve this problem ? 

The STM32USB library calls the function CDC TransmitFS, which can only be sent in the CDC ReceiveFS loop and data in the main. The cdc ->TxState flag has always been 1, so only the USBD_cDC SetTxBuffer was successfully called. However, the USBD_cDC TransmitPacket, USBD_cDC DataIn, and subsequent CDC TransmitCplt cannot be called.There are two solutions to watching the forum: 1. Place it in an interrupt with the same priority as USB and call CDC TransmitFS to send it. Only the call succeeds 2. 'Call this function EP0_RxReady before sending. But both methods can cause the program to freeze.Both CDC_Receive_FS and CDC_Transmit_FS are implemented in usbd_cdc_if. c. Calling CDC_Receive_FS in CDC_Receive_FS can send and receive messages in a normal loopback. The following is the implementation of two functions：

Hello,I am using an STM32H755 dual core chip and occasionally, our reset reason (RCC_RSR) is decoding to have only theD1RSTF bit and D2RSTF bit set.  Per the documentation, it does not seem this is an expected combination alone...Per table 56 in section 9.4.4, seems only valid reasons with either of those bits set are:(doc I am referring to is the ref_manual_rm0399-stm32h745755-and-stm32h747757-advanced-armbased-32bit-mcus-stmicroelectronics-2.pdf) Power-on reset (pwr_por_rst) - but this should have an additional 3 bits (PORRSTF, PINSTF, and BORRSTF bits)D1 exits DStandby mode - but this should only have D1RSTF  set  (and, not using standby currently)D2 exits DStandby mode - but this should only have D2RSTF  set (and again, not using standby currently)