STM32CubeMonitor (MCUs)

I want to store the stm32 cube monitor graph data or store the corresponding variable data in to xml sheet. How can I do that.

Hi, I'm using a fresh debian testing (12) and when i try to launch "SetupSTM32CubeMonitor-Power.jar", i get the error :Command line arguments: SEVERE: java.lang.ArrayIndexOutOfBoundsException: Index 70131 out of bounds for length 22674Debian is not in the supported operating system, but ubuntu should not be so far. I found on the forum, that the error occured on stm32cubemonitor on ubuntu recent version.Is there a patch/upgraded planned or anyway to make it run ?Could someone on ubuntu tell me if it work on it ? Thanks in advance,

Hello,I'm running ubuntu 24.04 and running STM32CubeMonUCPD with "jara -jar SetupSTM32CubeMonitor-UCPD.jar" fails with error  Command line arguments:SEVERE: java.lang.ArrayIndexOutOfBoundsException: Index 70131 out of bounds for length 22674This same thing happens for both version 1.4 and 1.3 of ucpd monitor. What are my next steps? Kind regards

Hello,I am experiencing an issue with STM32CubeMonitor on Windows 11 where some nodes, including acquisition out, are marked as "not found" and cannot be used.I have found similar reports from other users:https://community.st.com/t5/stm32cubemonitor-mcus/cubemonitor-acquitions-installing/td-p/660215https://community.st.com/t5/stm32cubemonitor-mcus/missing-acquisition-nodes-on-macos/td-p/644151I have tried the suggested solutions, such as running stlinkserver, but the issue persists. After starting stlinkserver, is there any additional setup required?Has anyone solved this issue using a different approach?

Hi,I am using a custom board based on STM32G4. I have successfully generated SINK code using cubemx and testing it using UCPDcube monitor. Explicit contract has done correctly but unable to select a source PDO. PFA, trace, and screenshot.  I appreciate any help you can provide.@FBL , Can you please check

Dear staffs,I'm going to use "STM32CubeMonitor" for several Nucleo boards, such as Nucleo144 of STM32H563.But, when I try to invoke, following dialog appears and does not proceed.Why ?Thank you 

I'm currently facing a frustrating problem with STM32Monitor. When I'm trying to parse data, the progress bar gets stuck at 10%. As a result, I'm unable to pull the project data list.Hardware environment: Windows 11

Hello,i use STM32WB05KZ for the bluetooth.With software can use to programme or to do some BLE test ?thanks

I downloaded Cube Power Monitor and am trying to use it to connect to the LPM01A. I have downloaded and installed the W8 version of the virtual com port driver. I can select the board in the drop down menu, but when I hit "Take Control", a dialog box pops up with the message `error pwr get`. When I hit okay, another pops up with the message `Get current range command failed` with another message below it `ERROR TIMEOUT`. Hitting ok

Mac refuses to start STM32CubeMonitor, it seems the app is neither code signed nor notarized.Happens with latest release 1.10.0

Hi  I have the cube monitor plugged in , and running the cube monitor power application. I had it working on my old computer (Windows 10) , but had to install the USB driver of ST web site. Since moving to my new computer, I cant find the driver again. Anyone point me to where it will be? My new computer is WIndows 10 too, and installing the cube monitor power application doesnt install the driver Many thanksScott

Hello A new 2.17.0 version of STM32CubeMonitor-RF is available on st.com. Click on "Get latest" to download the version 2.17.0. What are the main changes in this version ? Alignment with STM32CubeWB firmware 1.22.0 Alignment with STM32CubeWBA firmware 1.6.0 Alignment with STM32CubeWB0 firmware 1.2.0 Support of STM32WBA6x devices Bug fixes Changes details can be found in release note Do not hesitate to create new posts if you have any question. The STM32CubeMonitor-RF team.

On launch the STM32CubeMon-UCPD icon appears briefly in the dock and then disappears. The application does not launch. 

Hello A new version 1.10.0 of STM32CubeMonitor is available on st.com. You can download it on https://www.st.com/en/development-tools/stm32cubemonitor.html Click on "Get latest" to download the version 1.10.0. What are the changes in this version ? Node-RED® updated to version 4.0.7 GDB update to version 14.2, the new GDB is compatible with Ubuntu® 24.04.  Added the possibility to reset the log timing in the processing node, by sending a message with topic set to "clear". Added the support for snapshot mode with SEGGER J-Link probe Increased J-Link acquisition speed. Added a link to video tutorials

Hello,I would like to ask a question, if it is possible to access UCPD monitor via USB-UART bridge? I am following tutorial AN5418, with nucleo G0B1RE and SNK1M1 shield. Everything works fine when I use st-link, but when using uart bridge I dont see the board in board selection of UCPD and can log data only to UCPD trace...I have found out, that one can make it to work when one desolderes SB16 and SB15 from st-link on nucleo and connects LPUART to TX and RX of JP6. But is it also possible to make it w

Dear Sir,When I monitor the data, sometimes the value often accompanied by spikes, such as followed figure. In my case, I monitor 3 variables that update from ADC registers.

Hi,I would like to set the minimum and maximum values of a dashboard chart using custom values calculated with a processing node.I tried "single value" and "change" nodes, but without success.I attached my current flow...Thank youWalter

Hi,STM32CubeMonitor-UCPD sometimes displays RDOs like this:Where does the number MaximumOperatingCurrent come form? Since the RDO is defined as: typedef struct { uint32_t MaxOperatingCurrent10mAunits : /*!< Corresponding to min if GiveBackFlag = 1 */ 10u; uint32_t OperatingCurrentIn10mAunits : 10u; ... } USBPD_SNKFixedVariableRDO_TypeDef; MaximumOperatingCurrent should correspond to the lowest 10 bits of the data. These are 0x05 0x14 as displayed in "DATA:" in the monitor. This would mean that MaximumOperatingCurrent is 5, no

Hallo, I am saving the log files of the chart in the CUBEMonitor software. I read certain values from the MCU through Cube Monitor and save them as .CSV. However I've noticed that the first file I save after opening the software does start from 0 seconds. In case I stop the data acquisition and clear the chart and start it again. A new log file is created with advanced time i.e. although the chart does show the time scale to be from 0 seconds. This problem doesn't occur if I restart the software, but it is tedious everytime to restart the software. Is there a way I can reset the time for every acquisition made? Thanks

Hi everyoneI need to capture the step response from a temperature regulator circuit (for estimating regulator parameters) and I want to use Cube Monitor for that.No I get the example successfully running with a simple acquisition, but I stuck with further adjustions.As far I see, Cube Monitor can't handle booleans, so I simply switch to integer variables and just compare them with 0, it looks like this here in my main code:#ifdef ACQUIRE_STEP_RESPONSE while(waitForStartingStepRespone == 0){ } setHrtimPwmToAll(stepresponseStepSetting); while(waitForEndingStepRespone == 0){ } setHrtimPwmToAll(0.0); #endif So I just set the variable waitForStartingStepResponse to 0 by hitting a button. I read this article here ( https://wiki.st.com/stm32mcu/w

Hello,I would like to trigger a STM32 device reset from inside STM32CubeMonitor.I'm developing an application using STM32CubeIDE and STM32CubeMonitor. Duringe measuring of my variables via STM32CubeMonitor it is possible that my device gets into a reduced function safe state (on purpose). Then it would be very helpful to trigger a device reset via a button like I'm able to do during debugging in STM32CubeIDE.I understand currently only the topics: Read, Start and Stop are available for a probe-node. Is it possible to trigger a reset via additional (maybe undocumented) options or is this feature planned in a future release?If not is there a workaround available? I tried to connect to the GDB server opened by the probe-node after starting the acquisition but wasn't successful. As far as a saw it, the server is always opend on a different port?!. Thank youBest regardsMartin

Hello A new 2.16.0 version of STM32CubeMonitor-RF is available on st.com. You can download it on https://www.st.com/en/development-tools/stm32cubemonrf.html Click on "Get latest" to download the version 2.16.0. What are the main changes in this version ? Alignment with STM32CubeWB firmware 1.21.0 Alignment with STM32CubeWBA firmware 1.5.0 Alignment with STM32CubeWB0 firmware 1.1.0 Upgrade supported Open thread stack to API 420 version 1.3.0 Update 802.15.4 sniffer firmware Add STM32WB0X FUOTA support Changes details can be found in

Dear all, We are pleased to announce that STM32CubeMonitor-UCPD 1.4.0 has been released and is available on st.com. This tool is the perfect companion for customers dealing with our USB Type C solution. This new release of STM32CubeMonitor-UCPD supports decoding of EPR traces (EPR for Extended Power Range). To know more on this SW, please look at this introduction on YouTube :

Dear All, I want to use STM32CubeMonitor to monitor 64-bit variables, such as int64_t or uint64_t. However, it seems that 64-bit variables cannot be selected from the variable list (they are not displayed).

Hi everyoneI have a - for sure very basic - CubeMonitor flow. The goal later is to achieve a step response for regulator parameter estimating, but at first I want to start with showing temperatures only and fail here. What I managed to do already:Probe connecting seems to be successfull.Importing the .elf file seems to be successfull.Deploying also works.I put some screenshots in, maybe somebody else has an idea what goes wrong here?