STM32CubeProgrammer (MCUs)

Hi everyone,How can I uninstall the STM32CubeProgrammer on Ubuntu? I check inside the folder and has an uninstaller.jar, but nothing happens. $ sudo java -jar uninstaller.jar   The uninstaller has put a log file: /tmp/izpack18013613561370631600.logAnd inside the /tmp/izpack18013613561370631600.log has2023-03-06T16:41:55.158 Phase 1: JarFile: /home/charlesdias/STMicroelectronics/STM32Cube/STM32CubeProgrammer/uninstaller/uninstaller.jar 2023-03-06T16:41:55.255 Phase 1: Extracted 1078 files into /tmp/izpack18013613561370631600.d 2023-03-06T16:41:55.266 Phase 1: Spawning phase 2: /usr/lib/jvm/java-11-openjdk-amd64/bin/java -classpath /tmp/izpack18013613561370631600.d -Dself.mod.base=/tmp/izpack18013613561370631600 -Dself.mod.jar=/home/charlesdias/STMicroelectronics/STM32Cube/STM32CubeProgrammer/uninstaller/uninstaller.jar -Dself.mod.class=com.izforge.izpack.uninstaller.Uninstaller -Dself.mod.method=uninstall -Dself.mod.phase=2 com.izforge.izpack.util.SelfModifier 2023-03-06

When running stm32_programmer_cli.exe -l the first run shows a valid SN and FW version.The 2nd and subsequent runs show corrupt SN and FW version.The STM programmer version is 2.13.This repeats on 2 new ST Link debuggers.This repeats on 2 different computers.Please see image 

Hi ST, can you please look into this link STM32CubeProgrammer & STM32CubeMonitor support SEGGER's J-Linksand let us know which version of the cube programmer support jlink. A.Satt

Is it planned that in the future the cube programmer will also work with the j-link like the cubeIDE?

Hello, I am trying to regress from RDP2 on my STM32U585AII6. I have no problem doing this from the STM32CubeProgrammer GUI, but when I try using the STM32_Programmer_CLI software I get:.\STM32_Programmer_CLI.exe -c port=SWD mode=UR -unlockRDP2 0xHighKey 0xLowKey-------------------------------------------------------------------STM32CubeProgrammer v2.13.0-------------------------------------------------------------------ST-LINK SN : 0042001A4D46500F20383832ST-LINK FW : V3J13M4B5S1Board : STLINK-V3SETVoltage : 3.26VError: Cannot connect to access port 0!If you are trying to connect to a device with TrustZone enabled please try to connect with HotPlug mode.If you are trying to connect to H5 device and your target is already locked with password or certificate, please open your device using Debug Authentication.-----I get the same result when I try with mode=hotplug. After executing these lines the device comes up as normal, so the flash is not getting touched. When I go through the GUI, t

Processor STM32WLE4CThe latest STM32CubeProgrammer_CLI is not working, and it's not setting:WRP1A_STRTWRP1A_ENDWRP1B_STRTWRP1B_ENDIt looks like an error.The sequence of steps to reproduce the issue.1) In the microcontroller's memory, I have code that has read and write protection enabled.~/STMicroelectronics/STM32Cube/STM32CubeProgrammer/bin/STM32_Programmer_CLI -c port=SWD mode=UR -ob displ-------------------------------------------------------------------STM32CubeProgrammer v2.15.0-------------------------------------------------------------------ST-LINK SN : 56FF6C067870545131410967ST-LINK FW : V2J29S7Board : --Voltage : 3.13VSWD freq : 4000 KHzConnect mode: Under ResetReset mode : Hardware resetDevice ID : 0x497Revision ID : Rev YDevice name : STM32WLxxFlash size : 64 KBytesDevice type : MCUDevice CPU : Cortex-M4BL Version : 0xC4UPLOADING OPTION BYTES DATA ...Bank : 0x00Address : 0x58004020Size : 96 Bytes[==================================================] 100%Bank : 0x01Address :

while I install the stm 32 cube programmer oin my computer during the installation processes the computer asks me  to install a driver I click yes and I have the programmer installed on my computer like normal but when I go to usb to Seach for devices to connect to the programmer I don't see any, I look into my device management tab and see no stm 32 bootloader device in the usb tab. I'm running windows 10 and ran the correct windows download for my computer so idk what's up. If curious what I'm doing I am trying to flash firmware over my fly sky fs i6x radio transmitter to get express lrs on the controller. I do this by putting the controller into dfu mode and connecting to the programmer but I cant do this because there is no driver to connect the two. I'm new to all of this so help would be great. feel free to say anything if you have a thought.   In the picture on the top the circled other devices device is the transmitter in dfu mode, below you can see all the

When I was using the STM32CubeProgrammer software, I selected the USB connection development board, and directly reported the error: "Device is under read out protection! If you want to disable RDP please reconnect with Read Unprotect enabled." But the strange thing was that the other computer was normal,Have you ever had that? That's been bothering me for a long time

Good day!Having just acquired a disco stm32g031j6, I discovered that while my CubeProgrammer has no issues connecting to it, ST-LINK Utility doesn't like it - it hangs on Target/Settings for a while, shows S/N in the drop-down box but doesn't recognize the device and refuses to connect to it, suggesting "Normal" or "HotPlug" modes or lower SWD frequency (neither make a difference).I tried same with some of my other Nucleo boards (C031C6) and they had no problem connecting (though it couldn't recognize family either :14:02:46 : ST-LINK SN: 066BFF35314B4E304319573714:02:46 : V2J43M2814:02:46 : Connected via SWD.14:02:46 : SWD Frequency = 4,0 MHz.14:02:46 : Connection mode : Connect Under Reset.14:02:46 : Device ID:0x45314:02:46 : Device family :Unknown deviceIt could only do this under "Connect under Reset", not Normal mode) Yet, ST-LINK Utility had no problem recognizing and upgrading firmware from ST-LINK/Firmware Update menu route. Attaching screamshots from settings dialog and e

STM32CubeProgrammerを使用してボードをConnectしようとしたがErrorが発生する。使用しているボードはSTM32F746です。STM32cubeideでプロジェクトをRunした後にDebugをしなかった後にこのような動作が発生するようになりました。ジャンパーピンは5Vlinkに接続しUSBにてPCと接続しています。対処法を教えていただきたいです。

I am using a Wio-E5 mini devboard by Seed-studio and an ST-Link/V2 to program it.After setting the Read Out Protection to AA, I was able to read and write from and to the memory and do a mass erase.However, programming from CubeIDE always failed. I was not able to find out why exactly it failed, but got frustrated after a while and since it felt like I could always reset by doing a chip erase, I set all user configuration option bytes to zero to see what it does.Since then, the uC seems to be bricked. I can still connect to it and (supposedly) read the memory, but I am unable to write any data to it, be it Options Bytes, trying to erase selected sectors, doing a full chip erase or uploading a hex file.The Core State is always halted.When trying to write any options byte, I get the following error (here an example trying to set the nBOOT1):The error when I try and do a mass erase:Read out protection is set to AA:PCROP protection has the following values:Write Protection has the fol

I failed to make the .stldr for a NAND flash. I have followed the steps of initial System CLK, GPIO, NAND, and then Erase&Write the chip. Unfortunately, nothing wroted into the flash.The open resources are more about SPI/QSPI. It is helpful if there are any souce codes for NAND flash such as the one created 512W3A_STM3210E-EVAL.stldr.

Hi,I want to load a program so that when I unplug from computer and plug it again it is still running. To load the binary, I am using STM32 Cube Programmer. The program is correctly running, but when I click on the "Disconnect" button it stops running. It only starts running again when I click on the "Connect" button.Which configuration I am missing?Thanks,Alberto

I tried to connect but it's always: "No STM32 target found! If your product embeds Debug Authentication, please perform a discovery using Debug Authentication"I also try "Under reset" mode but still not working.Can someone help me

..

Hello,After installing STM32CubeProgrammer v2.16, I was unable to program a STM32F412 by USB (in DFU mode).I've never had a problem doing this and after uninstalling v2.16 and installing v2.15, everything worked fine.This problem was also confirmed by my colleague who is in a different location. Here is the log for v2.15:12:22:33 : STM32CubeProgrammer API v2.15.0 | Windows-64Bits12:22:48 : UR connection mode is defined with the HWrst reset mode12:22:48 : USB speed : Full Speed (12MBit/s)12:22:48 : Manuf. ID : STMicroelectronics12:22:48 : Product ID : STM32 BOOTLOADER12:22:48 : SN : 3141B956323812:22:48 : DFU protocol: 1.112:22:48 : Board : --12:22:48 : Device ID : 0x044112:22:48 : UPLOADING OPTION BYTES DATA ...12:22:48 : Bank : 0x0012:22:48 : Address : 0x1fffc00012:22:48 : Size : 16 Bytes12:22:48 : UPLOADING ...12:22:48 : Size : 1024 Bytes12:22:48 : Address : 0x800000012:22:48 : Read progress:12:22:48 : Data read successfully12:22:48 : Time elapsed during the read operation is: 0

Hello,I'm using STM32CubeProgrammer version 2.16.0. The debugging works fine, but if the connection with the target is lost or probably some bad message is received on the client side, the application crashes. So in the first place I can't even see the last SWO messages that were received from the target.Hardware: STM32U585 - SWD - HW Reset - ST-Link V2.0 ISOL @ V2J43S7System log attached. thx,- Martin

Hello all, I just updated my STM IDE and now, if I want to upload or debug my code I get this errorsAn this is the output in the console:My computer finds the board as usual:I tried powering off the board, switching the port, but it did not work, if you have any ideas I would be grateful. Thank you! 

After upgrading CubeProgrammer to new release 2.16 CLI commands started to fail during verification phase when changing option bytes on STM32U5A5. Sample command which fails:STM32_Programmer_CLI -c port=SWD mode=UR --hardRst -ob WRP1A_PSTRT=0xff WRP1A_PEND=0The same operation performed from GUI works correctly. I had to go back to release 2.15

I am able to read a memory location but do not have to save the result to a file.  here is my command STM32_Programmer_CLI.exe -c port=swd mode=ur Freq=4000 -r16 0x803c000 0xA c:\TPD\ST_Prog\guid.bin The data is displayed in the cmd window correctly 0x0803C000 : 0614 BB17 E000 D169 6E39   how can I save it to file.  I tried adding a path to the end of the command but nothing is saved.  Am I missing a -xxx command somewhere?

I am using STM32_Programmer_CLI and need a list of all possible error codes.  Where are they located?

Hello Team,We are facing an issue while programming our MCU from STM32Cube Programmer. The error we are having is shared below:18:50:44 : ST-LINK SN : 36FF7006564834385641104318:50:44 : ST-LINK FW : V2J43S718:50:44 : Board : --18:50:44 : Voltage : 3.25V18:50:44 : Error: No STM32 target found!Out of 100, 30 boards are unable to connect with STM32CubeProgrammer.MCU we are using is STM32L452REY6.

Think like users, think about how to present diagnostic data that can convey useful information. Use the tools as if you were a User, test basic functionality and interaction so you KNOW it works properly.Here trying to understand interactions with an External Loader in STM32 Cube Programmer.I'm fine with one line of information, but put some actual information in that line, ie for a Read the Address and Size would be a MINIMUM.I'd use Level 3, but the method used for the Logging Window CHOKES when doing a million SMALL reads on a 32MB SPI device when verifying. What controls the size, the H7 has loads of RAM it uses on Writes?Sorry if I sound frustrated, but I've tried to use these tools for years, they aren't getting markedly better and seem to lack any Quality Assurance or any desire to address basic issues over the span of multiple years.@brk​ 

Hi, I'm trying to create a C# wrapper for STM32CubeProgrammer_API.dll. In version 2.10, the downloadFile function worked perfectly within my C# wrapper. However, upon updating to version 2.15 of the STM32CubeProgrammer_API.dll, the function no longer operates as expected. This is the output I receive when I try to use the function Memory Programming ...Opening and parsing file: data.hexFile : data.hexSize : 3.76 KB Address : 0x08000000 File segment @0x08000000 is not 255-bytes aligned. It will be aligned to @0x07FFFFF8Download in Progress:Size : 4080 BytesAddress : 0x07FFFFF8 Buffer program...w ap 0 @0x07FFFFF8 : 0x00000FF0 bytes, Data 0xFFFFFFFF...Error: failed to download Segment[0]Error: failed to download the File Thanks

Hi,I'm trying to program a hex file generated with 'TrustZone disabled' software model targeting STM32H563ZIT6 (NUCLEO-h563ZI) as:"C:\Program Files\STMicroelectronics\STM32Cube\STM32CubeProgrammer\bin\STM32_Programmer_CLI.exe" -c port=SWD freq=4000 sn=040917021e8903bf00000000000000000000000097969906 -d C:/Users/WCarey/repositories/projects/keil/stm32h563zi/Release/Objects/ucomm_example.hex -gThis results in the error:So, I changed the access port to 1:"C:\Program Files\STMicroelectronics\STM32Cube\STM32CubeProgrammer\bin\STM32_Programmer_CLI.exe" -c port=SWD freq=4000 ap=1 sn=040917021e8903bf00000000000000000000000097969906 -d C:/Users/WCarey/repositories/projects/keil/stm32h563zi/Release/Objects/ucomm_example.hex -gThough the serial number is correct, there's a DEV_CONNECT_ERR. The hex has NOT been loaded properly because when I try to open up a serial monitor like Teraterm, I am unable to receive any data.Can anyone point out how to load the hex file?Thanks in advance.NOTE: I am able