Product forums

Can I join a LoRaWAN network only once?so that after a software or hardware reset, i would not need to join the same network once again I am working with LoRaWAN_End_Node_LBM example

Hello. I have a custom stm32mp135f  board with emmc1(SDMMC2) and about to launch linux.(Minimized version of 135f-dk, no-sdcard, no-ethernet)I flashed the target with the CubeProgrammer normally.When the kernel loads userfs there says 'root '/dev/disk/by-partuuid/491f6117-415d-4f53-88c9-6e0de54deac6' doesn't exist or does not contain a /dev." and stopped.How do I solve this problem?This is full log capture.Starting kernel ... I/TC: Reserved shared memory is disabled I/TC: Dynamic shared memory is enabled I/TC: Normal World virtualization support is disabled I/TC: Asynchronous notifications are enabled [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 6.6.48-gd96ac4cc57f6 (oe-user@oe-host) (arm-ostl-linux-gnueabi-gcc (GCC) 13.3.0, GNU ld (GNU Binutils) 2.42.0.20240716) #1 PREEMPT Fri Jun 20 08:08:22 UTC 2025 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.

I am currently working on the STM32N6570-DK board and need guidance on FSBL configuration, multi-layer project structure, and external flash programming.Issue 1: FSBL Peripheral ConfigurationI enabled multiple peripherals in FSBL:USART1, I2CBSPXSPI1, XSPI2CSI, DCMIPPVENC, JPEGAfter enabling these, I am getting an "unsupported relocation" error.Kindly guide:Which peripherals are recommended to enable in FSBLWhich peripherals should be initialized in the Application layer insteadProper distribution of initialization between:FSBLApplicationExternal Memory LoaderIssue 2: Multi-Layer Project UnderstandingCurrently, the project has:Three separate layers (FSBL, Application, External Loader)Each has its own startup file and main functionI would like to understand:How these three layers work togetherExecution flow between FSBL → ApplicationHow memory mapping and control transfer happenThere are three separate build outputs—which one should be flashed?How will all three sections work together in

I would like to connect a 12-bit ADC operating at 10MSps to the PSSI interface of the STM32N657 device.  There is some confusion as to the nature of the clock source. The reference manual indicates that this may be either an input or an output.  If configured as an output, what is the source of the clock?  Examples suggest that a PWM timer needs to be used.  Here is an illustration of what I would like to do:Do I need to use the PWM timer as the clock source?

Hello everybody.I try to convert an STM32CubeIDE project into a CMake project to be used on VSCode using the procedure included in "STM32CubeIDE for Visual Studio Code" extension.The procedure aborts with this error message:  [Error] [ide-project-convert] Bad escaped character in JSON at position 15583 (line 322 column 55). Line 322 of "stm32cubeide-export.json" file, created by the procedure itself, is this one:, "option.includepaths": "-I\"C:\Repo_mgo\STM32Workspace\NGDrive\Appl\dDrive_Fwk2\application\Display\TouchGFX\generated\texts\include\", -I\"C:\Repo_mgo\STM32Workspace\NGDrive\Appl\dDrive_Fwk2\application\Display\TouchGFX\", -I\"C:\Repo_mgo\STM32Workspace\NGDrive\Appl\dDrive_Fwk2\application\Display\TouchGFX\gui\include\", -I\"C:\Repo_mgo\STM32Workspace\NGDrive\Appl\dDrive_Fwk2\application\Display\TouchGFX\generated\gui_generated\include\", -I\"C:\Repo_mgo\STM32Workspace\NGDrive\Appl\dDrive_Fwk2\application\Display\TouchGFX\generated\fonts\include\", -I\"C:\Repo

The API documentation for the "AT+CIPSTART" command on the ST67W611M1 chip seems to be incomplete. It is missing the parameter lists for UDP and SSL types. https://wiki.st.com/stm32mcu/wiki/Connectivity:ST67W611M_AT_Command#AT-2BCIPSTART The rest of the API is documented on the ESP-AT page: https://docs.espressif.com/projects/esp-at/en/latest/esp32/AT_Command_Set/TCP-IP_AT_Commands.html#at-cipstart-establish-tcp-connection-udp-transmission-or-ssl-connection

I am currently working with the LoRa-E5 Mini module based on the STM32WLE5JC microcontroller, and I am using STM32CubeIDE version 2.1.0 for development. I have successfully tested basic GPIO functionality (LED blinking), and I am now trying to implement LoRa-based communication (transmission and reception) using the integrated SubGHz radio. However, I am facing challenges in properly configuring and utilizing the SubGHz_Phy middleware and radio drivers within STM32CubeIDE. Specifically, I need guidance on the following: The correct procedure to enable and configure the SubGHz radio peripheral in STM32CubeIDE for STM32WLE5JC. How to properly include and use the SubGHz_Phy middleware for basic LoRa communication. Availability of any official example projects (such as Ping-Pong or Tx/Rx) compatible with STM32CubeIDE 2.1.0 for the LoRa-E5 Mini module. Proper configuration of radio parameters (frequency, spreading factor, bandwidth) for reliable communication. Any recommended steps to ensu

Hello,I am using VSCode on Windows with the STM32CubeIDE for VSCode extension.Before installing the extension, I had already installed and configured these tools separately on my system:CMakeArm GNU Toolchain (arm-none-eabi-gcc, arm-none-eabi-gdb)clangdAfter installing the STM32CubeIDE for VSCode extension, build works, but debug fails to start. I get the following popup error:bound doStepStartGdbClientDebug Failed: Failed to get gdb version.I would like to ask whether this issue may be related to how the extension detects GDB, conflicts with environment variables, or path priority when multiple toolchains are installed.Observed behaviorI already had a standalone ARM toolchain installed before installing the STM32CubeIDE for VSCode extension.After installing the extension, debug no longer starts correctly.The popup error is:bound doStepStartGdbClientDebug Failed: Failed to get gdb version.My current suspicion is that the extension is either:not finding the correct arm-none-eabi-gdb, or

I have a STM32WB05TZF6TR. All VCCs are running off 1.8V. I'm trying to use PA8 and PB5 with 3.3V 10k pullups. But the signals are being clamped at 2.5V. I had expected this not to happen, as they are supposed to be 5V tolerant. Does anyone know what's happening here? There's nothing connected to the pins besides the pullups. I have a bare STM32CubeMX project, with just this GPIO init:void MX_GPIO_Init(void){ GPIO_InitTypeDef GPIO_InitStruct = {0}; /* GPIO Ports Clock Enable */ __HAL_RCC_GPIOB_CLK_ENABLE(); __HAL_RCC_GPIOA_CLK_ENABLE(); /*Configure GPIO pin : PB5 */ GPIO_InitStruct.Pin = GPIO_PIN_5; GPIO_InitStruct.Mode = GPIO_MODE_INPUT; GPIO_InitStruct.Pull = GPIO_NOPULL; HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); /*Configure GPIO pin : PA8 */ GPIO_InitStruct.Pin = GPIO_PIN_8; GPIO_InitStruct.Mode = GPIO_MODE_INPUT; GPIO_InitStruct.Pull = GPIO_NOPULL; HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); } Much appreciated,David 

(I've opened an issue on GitHub on this matter already, but I was asked to post it here again...)Hey there,I'm currently developing an audio application based on the STM32N657 MCU. I have already implemented a working version of this application on an STM32U5A5 MCU, but now I need to port it to the N6.The application receives a PDM audio stream from a MEMS microphone via SAI. The audio data is then converted to PCM using the PDM2PCM library. On the STM32U5A5 MCU, the application uses the CM33 variant of this library (libPDMFilter_CM33_GCC_wc32.a), but I cannot find a variant of this library for the CM55 of the STM32N6 in any of the STM32Cube firmware packages.I would be very grateful for any advice or help on this matter!Thanks in advance and best regards,Jens

Hello ST team,I am using a P-NUCLEO-LRWAN3 starter kit with the NUCLEO-F746ZG gateway board.I accidentally overwrote the original gateway firmware on the F746ZG. I have already recovered the board so that it can be connected and programmed again with STM32CubeProgrammer, but I no longer have the original gateway firmware binary.I tried flashing another gateway binary:st-nucleo-lora-gw-at-fw-v2.1.7-eu868-TTN.binThe firmware runs, but it is clearly not the correct one for my hardware. After flashing it, the serial output shows EU868 / TTN settings and reports:router.eu.thethings.networkuplink/downlink port 1700channels around 867–868 MHzERROR: Radio A frequency and type are not matchedERROR: Radio B frequency and type are not matchedBefore I overwrote the original firmware, the gateway output was different. The original serial output showed:VERSION: 2.1.7, Nov 6 2018LORAWAN SERVER: ap1.loriot.iouplink/downlink port 1780channels from 471500000 to 472900000So I believe the original firmwar

Hi everyone,I’m working on the STM32N6570-DK and trying to run a NetXDuo Web HTTP server as part of a secure application executing in XIP (external flash).I started from the available examples (which run from internal RAM / FSBL), but after moving the application to XIP, I’m facing instability issues (intermittent crashing issues, no ping response, etc.).From initial debugging, this seems related to:Execution latency from XIPPossible cache / MPU configuration or memory placement issuesMy questions:Is there any official or reference example for:STM32N6570-DKNetXDuo (HTTP Web server)Running in XIP mode (external flash)Within a secure application contextAre there recommended guidelines for:Placing NetXDuo and ETH driver code (RAM vs XIP)?MPU/cache configuration when using XIP with networking?Memory regions for packet pools and DMA buffers?Has anyone successfully run NetX Duo HTTP server reliably in XIP on STM32N6?

Split from STM32WB05KNV6TR missing in STM32CubeIDE 2.0.0 Target Selector - this is a new questionHi Ghofrane,Thank you for the explanation. Since the WB05xN acts as a network coprocessor, it doesn't fit my current design goals as I want to avoid using an external Host MCU to keep the BOM cost and PCB footprint at a minimum.I am looking for a standalone (single-chip) STM32 wireless solution. My requirements are:Standalone Operation: The application and BLE stack must run on the same chip.Eddystone Support: It must be capable of broadcasting in Eddystone format.FOTA (Firmware Over-the-Air): The chip must support wireless firmware updates.Cost-Effective: This is a price-sensitive project, so I am looking for the most budget-friendly standalone option in the STM32WB family.Could you please suggest the most suitable part number for this use case? Would the STM32WB15 or the new STM32WB09 be the right direction for a low-cost, standalone beacon application?

Hi all,I am working with STM32F469ZIT6 and external SDRAM AS4C4M16SA-6TIN SDRAM using FMC (Bank1).SetupHCLK = 180 MHz SDRAM clock configurations tested:HCLK/2 (90 MHz) → Refresh count = `0x056A`HCLK/3 (60 MHz) → Refresh count = `0x0395`Data width: 16-bitInternal banks: 4CAS latency : 2SDRAM clock has been verified using an oscilloscope and matches expected frequencies.Test CodeI am writing a pattern to SDRAM and reading it back:- Write pattern: `0xA1234567 + index`- Base address: `0xC0000000`  for (uwIndex = 0; uwIndex < BUFFER_SIZE; uwIndex++) { *(__IO uint32_t*) (SDRAM_BANK_ADDR + WRITE_READ_ADDR + 4*uwIndex) = aTxBuffer[uwIndex]; }Read back: for (uwIndex = 0; uwIndex < BUFFER_SIZE; uwIndex++) { aRxBuffer[uwIndex] = *(__IO uint32_t*) (SDRAM_BANK_ADDR + WRITE_READ_ADDR + 4*uwIndex); } Issue (Observed Behavior)- The read operation does not return the correct written data- Instead:It often returns the previous/last written value.The data pattern shows MSB dupl

Title: STM32N6 (NUCLEO-N657X0-Q) unable to flash on M3 Mac - libusb timeout errorEnvironment:- Board: NUCLEO-N657X0-Q (STM32N657X0H3Q, STLINK-V3EC)- Host: MacBook Air M3, Apple Silicon- STM32CubeProgrammer: v2.22.0- STM32CubeIDE: v2.1.1- ST-Link Firmware: V3J17M10- libusb: 1.0.29 (Homebrew)Problem:Unable to flash the board from M3 Mac. STM32CubeProgrammer and STM32CubeIDE both fail to connect consistently.Error from STM32CubeProgrammer CLI:ST-LINK FW : V3J17M10Board : NUCLEO-N657X0-QVoltage : 3.28Vlibusb: warning [darwin_transfer_status] transfer error: timed outError: Unable to get core IDError: No STM32 target found! If your product embeds Debug Authentication, please perform a discovery using Debug AuthenticationError from STM32CubeI

Hello everyone,I want to develop an IoT application based on STM32L496 and I am working with the BG96 modem that is embedded on P-L496-CELL02 board. The exchange of AT commands with the modem is succesfull, but, even though i insert a plastic microsim (I have actually tried two of them), i keep getting an error message "Sim Not inserted". I have enabled the simselect0 (PC2) and simselect1 (PI3) pins in CubeMX, as it is indicated by the manual (set to 0 and 1, respectively) and verify their value with my code. The board is powered with an external supply source, through Arduino Vin. The BG96 firmware version is BG96MAR02A08M1G. I have inspected soldering, short-circuits between the sim socket and contacts and everything seems to be alright. I cannot understand what could possibly be the problem, does anyone have a clue? I would be grateful.Here is my code. All AT commands return OK and seem to work.  int main(void) { /* USER CODE BEGIN 1 */ /* USER CODE END 1 */ /* MCU C

Good day, I am currently working on the development of an IoT sensor node product based around the STM32WLE5CC MCU. The product needs to be able to wake up from sleep on reception of a LoRa RF message. I have attempted to accomplish this by transmitting a long preamble and having the node receive the message by setting the radio in RxDutyCycle mode prior to sleeping. The timing of my duty cycle is such that I am guaranteed an Rx window within the preamble duration. This wakeup functionality works, however, the RSSI of the received wakeup signal is shown to be >20dBm lower than if I had just used continuous reception. This is a problem as we are now encountering suspected range issues where units can detect the preamble but fail to fully receive the associated payload. I have gone through multiple test setups with different spreading factors and the results are consistent across the tests: Test 1.1 (SF = 7, BW = 125 kHz, Preamble Len = 500, Rx = Full Receive) Wake RSSI = -

I'm using LPTIM1 in encoder mode and have noticed that, if there's jitter on one of the encoder signals the count will gradually creep up which should not be possible in encoder mode.This is on a decent encoder that's got an RC network (per the Bourns data sheet / appnote) in front of it too so this isn't nasty HF noise, it's good solid pulses of 50-100ms or more on one channel but the counter seems to creep up.Identical encoders wired to TIM2 / TIM3 behave normally, and my colleague has seen the same issue in another project using the same setup - LPTIM has a problem where TIMx does not.Init code for LPTIM1:/* LPTIM1 init function */ void MX_LPTIM1_Init(void) { /* USER CODE BEGIN LPTIM1_Init 0 */ /* USER CODE END LPTIM1_Init 0 */ LL_GPIO_InitTypeDef GPIO_InitStruct = {0}; LL_RCC_SetLPTIMClockSource(LL_RCC_LPTIM1_CLKSOURCE_PCLK1); /* Peripheral clock enable */ LL_APB1_GRP1_EnableClock(LL_APB1_GRP1_PERIPH_LPTIM1); LL_IOP_GRP1_EnableClock(LL_IOP_GRP1_PERIPH_GPIOB); /**LPTIM1 GPIO

Hello ST Community,I am currently working on a project using the STM32WB05KNV6TR microcontroller. I am using STM32CubeIDE Version 2.0.0, and I have ensured that all MCU packages and embedded software packs are up to date.Specifically, as shown in the attached screenshot, I have the STM32Cube MCU Package for STM32WB0 Series (v1.4.1) installed. However, when I try to create a new project and use the Target Selector (MCU/MPU Selector), the STM32WB05 series—and specifically the STM32WB05KNV6TR—does not appear in the list.I urgently need to access the Pinout & Configuration view to finalize my hardware design and verify the pin assignments.Steps I have already taken:Updated STM32CubeIDE to the latest available version.Refreshed and installed the latest WB0 series patches via the Embedded Software Packages Manager.Restarted the IDE and checked the board/MCU selector filters.Questions:Is there a specific patch or an external ".pdsc" file required to enable STM32WB05 support in CubeIDE 2.0

Hi Everyone, I am working on a NUCLEO-H753ZI board and want to set up Ethernet RMII communication using LwIP in STM32CubeIDE. I am looking for step-by-step guidance from the IOC file configuration to the generated code, including: Pinout configuration for RMII. LwIP middleware settings. MPU region configuration for Ethernet and LwIP memory Generating code and linker settings  Any tips to ensure that ping from PC works reliably   Could provide a complete, detailed guide. how to configure CubeIDE and LwIP for NUCLEO-H753ZI.     Thanks in advance.

Hello Community, I am struggling with a custom board design based on the STM32H743ZIT6 (LQFP144, non-SMPS version). I’ve replaced the MCU already, but the symptoms remain identical, suggesting a fundamental hardware/layout issue. The Symptoms: Current Draw: 10mA when BOOT0 = GND. Approx. 50mA when BOOT0 = 3.3V (System Bootloader). VCAP Voltage: Measuring approx. 1.0V. Debug Connection: Using Segger J-Link (V11). "Failed to initialize DAP" / "Can not attach to CPU". VTref is stable at 3.3V, NRST is at 3.3V. USB DFU: When BOOT0 = 3.3V, Windows reports "Device Descriptor Request Failed" (Unknown Device) when connected via usb. SWD Pins: PA13/PA14 show ~1.6V when floating (no debugger connected), which is highly unusual Same Symptoms if 3.3V are supplied by ams1117 or laboratory power supply My Schematic: VBat, all Vdds, Vdda, VRef, PDR_ON are all connected to 3.3V all GNDs and AGND are connected to GND each Vcaps (2x) has a 2.2uF capacitor (alltough i am not sure abo

Could I get some guidance on this? Presumably I can fix this by installing a package or something...Logs below (see second line from end).Thank you! 2026-04-12 17:30:29.505 [Info] [project-manager] STM32CubeIDE project manager activation....2026-04-12 17:32:30.960 [Info] [ide-project-convert] Starting project conversion...2026-04-12 17:32:31.263 [Info] [ide-project-convert] cube wrapper version: 0.10.22026-04-12 17:32:31.551 [Info] [ide-project-convert] Starting installation...2026-04-12 17:32:31.689 [Info] [ide-project-convert] Do you want to install the following bundles: ["osgi-exporter@0.0.4"] (yes, no, show)?2026-04-12 17:32:31.692 [Info] [ide-project-convert] Downloading osgi-exporter@0.0.4 to '/Users/me/Library/Application Support/stm32cube/bundles/osgi-exporter/0.0.4'...2026-04-12 17:32:32.004 [Info] [ide-project-convert] Downloading https://developer.st.com/bundles/o/osgi-exporter-0.0.4-all.bundleDownloading https://developer.st.com/bundles/o/osgi-exporter-0.0.4-all.bundl

Hi, for an old project of mine I need the STM32CubeF4 v1.21.0 +  HAL v1.5.7 but I can't find the download links to that version anymore. It seems like they got deleted from GitHub? Can someone supply me with the old version of the STM32CubeF4 including the HAL? Cheers!

Hi Is there an example using a STM32C5 as a USB host controller connecting a USB HID (mouse/keyboard) as input device?

I have a 14-pin connector and a 6-pin fall back connector. I can connect the 6-pin SWD via st-link V2 on a nucleo board but I cannot connect with a V3 MINIE on the 14-pin. Any ideas? I followed the schematic for a 14-pin connector I found on a NUCLEO board, which had a 100 ohm resistor on GND detect. I have bypassed it but the result is still the same. Apart from that and the TX/RX, the wires are the same for the 6-pin connector that works?Here's my output:CDLiveWatchSetup Info : auto-selecting first available session transport "hla_swd". To override use 'transport select <transport>'. Info : The selected transport took over low-level target control. The results might differ compared to plain JTAG/SWD Warn : The selected adapter does not support debugging this device in secure mode adapter speed: 24 kHz none separate Info : Listening on port 50004 for tcl connections Info : Listening on port 50005 for telnet connections Info : clock speed 24 kHz Info : STLINK V3J14M5 (API v3) V