STM32CubeProgrammer (MCUs)

Hi,I've created *.stldr for custom hardware.My hardware use HyperFlash with first sector divided in smaller sector.Configuration is :Sectors are contiguous but in STM32Cubeprogrammer each sector type start at DeviceStartAddress and not at the end of last previous sector.Does this issue come frome STM32CubeProgrammer or from the code?224K sector start at 0x70008000 and first 256K sector start at 0x70040000...Thanks for your help.Have a good day.Aurélien

When the SysTick interrupt fires the debugger quits. I cannot figure out where the NVIC_SetVector statement is for the SysTick. I think it is not set. But I can not find the vector table in the debugger to know for sure. This used to work, But when I updated to the 1.10.1 IDE and 6.6.1-RC2 Build.20220706-1420. It crashes when the systick interrupt happens. I am using the STM32G051K8T

Dear allI think the description is wrong or BOOT0/BOOT1 is swapped - see attachments.If the option bytes are programmed as shown under STM32CubeProgrammer.png, the controller boots from flash.Thanks in advance,Franz

Hi,i try to write the OTP area lock bytes using the ST-LINK/V2 programmer with the ST STM_Programmer_CLI tool included in the STM32CubeProgrammer software package.I can successfully write to the OTP area blocks using the -w32 command but if i try to also write the according Lock byte it will fail with the following error message:Command: STM32_Programmer_CLI.exe -c port=SWD -w32 0x1FFF7AC 0xFFFFFF00Error: Failed to download data!If it's a Flash memory, it may be not erased or protectedAny idea why the write fails for the Lock bytes while OTP blocks are successfully written ?

I am a beginner and I do according to this video "External Qaspi Loader How to - 05 - Qspi Driver Coding" https://youtu.be/XqCq0xtQmbI I uploaded the project "EXTERNAL QSPI Loader" to stm and now question about .bin fileHow to create a data file to be stored in the Flash memory,which can be a binary file or .hex? For example, I have a project "Hello World" and I want to upload it to external QSPI memory.I need as usual to create a project "Hello world" and just indicate in the stm32CubeIDE settings to create a .bin Or I need to make some additional settings for my "Hello world" project like, MPU configuration!?!And the resulting file, to program Quad-SPI Flash memory using the ST-LINK utility...

ST STM32F469NIi need to load and run an application in ram.with STM32CubeProgrammer via USART1 I load the code in flash without problems and it is executedIf I try to load a linked application to be run in ramSTM32CubeProgrammer in programming gives me the following erroras attachment

I've tried importing the examples into the IDE , complies fine but will not upload - i get the "Failed to execute MI command:" error if i use the stm32CubeProgrammer i can write to Flash(boot loader &program) but it never hands off to Qspi 0x90000000 i can make a small blinky program work out of the small boot flash - so is it me ? the IDE ? a bad dev board? (had successful projects utilizing f411' using the IDE ) possibly an explanation step by step like i'm 5years old ;) ?

If the name (filename) of module has more than one dot ( "." ) the STM32CubeProgrammer can list it in the external loder (EL) selection, but when STM32CubeProgrammer tries to use the module it fails (it generates an error).For example this EL name generates the error: EN25Q40_MT447R2_2.0.0.stldrthe same file renamed into EN25Q40_MT447R2.stldr (removing all dots) works.

 

..

..

Hey, sorry, I am pretty new to this. I have a rather basic question. I took apart a module that I have, within which there is STM32 microcontroller (part marking: STM32F103T8U77BA7E93PHL739). I want to know if it's possible to use the IDE to extract the existing bin file in the microcontroller, via JTAG or some other method? Reason being I have my own bin file that I'd like to test, but in case I screw things up, I'd like to be able to restore the module back to its original condition by reinstating the original bin file into the microcontroller. So my plan is to extract the current contents of the microcontroller by reading back, store the bin file safely before i do any kind of experimentation so that at least the original condition can be restored. Hope my question is clear.

I have an STLINK-V3SET connected to a Seeed Lora-E5. I also have a Nucleo L476 developement board with on-board STLINK. On the Seeed board I am able to connect STM32CubeProgrammer and have loaded a file. I cannot connect however STM32CubeIDE as I get an immediate failure to connect due to GDB server ....On the Nucleo I have successfully connected the STM Utility and downloaded a file but once again I cannot connect STM32CubeIDE. I downloaded all three of these apps today so they are the latest....CubeIDE is 1.10.0. The IDE was working just fine as I have flashed Nucleol476 and NucleoWB boards but somehow I have corrupted it's ability to use the GDB server. I deleted the debug and .launch but to no avail....Please help here as I no longer have the ability to use the IDE ????? UPDATE:removed 1.10.0 IDE and went back to 1.9.0....Below is the message received as I tried to load the application and run it on a NucleoL476....it got farther than it has but still some sort of issue???? Fu

Hi,the Serial wire viewer (SWV) has a command-line option. This only launch the viewer and the user has to press R to start.Is it possible to directly start the SWV?Or is there a shell trick for this? - Thomas*********************************************ManualSTM32_Programmer_CLI.exe -c port=swd -swv freq=32 portnumber=0C:\Users\ST\swvLog\example.logSerial wire viewer (SWV) command-SWVDescription: This command allows the user to access the serial wire viewer console mode,which displays the printf data sent from the target through SWO.In this mode (see Figure 105) the user can start and stop the reception of the SWO data by pressing, respectively, the “R�? and “S�? buttons on the keyboard. T

..

..

MCU STM32G473MXTCLI argument: -c port=SWD -e all -w C:\STM\Target.hexDuring connection/power interruption, the STM32_Programmer_CLI.exe return "0" as exitcode. (same exit code with programming successful result)

Hi everyone, I use a JumpToBootloader( ) function in my code to execute system memory bootloader. and then STM32CubeProgrammer connect ok, but it can not program​MCU:STM32G030K6T6 STM32CubeProgrammer: v2.4.0Boot Interface: UART1 (PA9 PA10)+MAX13487EESE(RS485 witch AutoDirection Control)here is JumpToBootloader(void)static void JumpToBootloader( void ){  uint32_t i = 0;  void ( *SysMemBootJump )( void );  /*declare a function pointer 声明一个函数指针 */  __IO uint32_t BootAddr = 0x1FFF0000; /* BootLoader address*/  /*Turn off global interrupts 关闭全局中断 */  __disable_irq();  /* Turn off the tick timer, reset to default 关闭滴答定时器，�?�?到默认值 */  SysTick->CTRL = 0;  SysTick->LOAD = 0;  SysTick->VAL = 0;  /* Set all clocks to default state, use HSI clock 设置所有时钟到默认状�?，使用HSI时钟 */  HAL_RCC_DeInit();  /* Disable all interrupts, clear all interrupt pending flags 关闭所有中断，清除所有

Hi,I have written a STM32H747 external loader for a NAND Flash on the FMC bus of the CM7. The test software of the loader functions (Init, MassErase, SectorErase, ...) works perfectly. The functions are called correctly by the STM32CubeProgrammer. As a test of the functions, I forward the parameters of the function calls and the results to a UART and can thus debug the "internal" processes. The initialization and erase works perfectly. When programming a page there is now an unsolvable problem. The functionint Write( uint32_t Address, uint32_t Size, uint8_t *buffer ) gets values for Size that are much too large. The hex file to be programmed is about 303kB. The 303kB are divided into only two programming cycles:1. Page programming address: 0x80000800 size: 0x0002502C 2. Page Programming Address: 0x8002582C Size: 0x00025000Why is the size 0x0002502C or 0x00025000 and not 0x800 as defined?The ext. NAND Flash starts at 0x8000'0000, the actual start is at 0x8000'0800.Here the StorageInfo:s

The STM32 Cube Programmer lets me read memory, but the address is required. It is not clear *where* the DFU loader puts a .hex file. What I want is to recover the hex file.

Hi,I'm trying to download a binary file into an external flash using the STM32CubeProgrammer with an .stldr file.I can Read, Erase, but the download doesn't work.The tool start by programming the first 0xFF addresses and stops.the error is Error: failed to download Segment[0].Can anyone help please ?

Hello everyone, I'm a beginner and want to try STM32 but there is a problem when installing STM32cube programming the message "CubeProgrammer_API or one of its dependencies is missing. Please try reinstalling the program of check your java". I use :osx :10.9.5java version "1.8.0_331"Java(TM) SE Runtime Environment (build 1.8.0_331-b09)Java HotSpot(TM) 64-Bit Server VM (build 25.331-b09, mixed mode).Thanks everyone hope someone can tell how to solve it.

Hi,I'm trying to migrate an old firmware from a STM32F303 to a STM32G474.The MCU is related to an external Flash W25Q16JV.The old configuration uses the SPI bus to communicate with the external flash.So I changed the program in order to adapt the new MCU.I know by the datasheet that the W25Q16JV can run on QSPI but this configuration is for later. After I changed the program I can generate the .stldr file and copy it in the external loader folder of the STM32CubeProgrammer. The STM32CubeProgrammer start but keep showing message about Flash protection. On the scope no signal at all. It seems that the program can't start due to incorrect boot vector and SP pointer.In the project there is no Startup.s file and no main. Q1: how the project is suppose to deal with that and where to declare missing starting point.Q2: Is there any example that shows the correct configuration.Thanks for your help

I have been working with STM32H753 device. I was able to boot into the system booltoader of the Nucleo board. Cube Programmer was able to detect and connect through UART.But, I am unable to connect the Cube programmer in our custom board. Both BOOT_ADD0 and BOOT_ADD1 were set to 0x1FF0. After booting, I connected J-Link to verify that the PC is at 0x1FFx series addresses.Looking further, whenver I halt and run the CPU through J-Link, the PC seems to be at address 0x1FF0AAF0 and the CycleCnt is increasing.I am not sure what could be possibly wrong.

This is the log: 16:37:14 : STM32CubeProgrammer API v2.8.0 16:37:32 : ST-LINK SN : 003500125553500D20393256 16:37:32 : ST-LINK FW : V3J8M3 16:37:32 : Board    : STLINK-V3MINI 16:37:32 : Voltage   : 3.00V 16:37:32 : SWD freq  : 24000 KHz 16:37:32 : Connect mode: Normal 16:37:32 : Reset mode : Software reset 16:37:32 : Device ID  : 0x413 16:37:32 : Revision ID : Rev 2.0 16:37:32 : UPLOADING OPTION BYTES DATA ... 16:37:32 :  Bank     : 0x00 16:37:32 :  Address    : 0x40023c14 16:37:32 :  Size     : 4 Bytes 16:37:32 : UPLOADING ... 16:37:32 :  Size     : 1024 Bytes 16:37:32 :  Address    : 0x8000000 16:37:32 : Read progress: 16:37:32 : Data read successfully 16