STM32 MPUs Products and hardware related

Hi,my situation is this:We want to use a "liveSD" image and boot from emmc by default if "liveSD" isn't found.The SD card should be inserted even if it is not a "liveSD" card, boot eMMC should be running.I know we could override the OTP boot sequence, but can BootROM detect this from the "partition table" or device?

I am testing lan by connecting usb ethernet (LAN7850) to stm32mp157f-dk2 board.Drivers microchip.ko and lan78xx.ko are loaded automatically and device eth1 appears normally.But when I connect or remove the cable to the lan port it doesn't recognize it.It appears to be registered as an interrupt, but the log is 0.$cat /proc/interrupts​92:     0     0 lan78xx-irqs 17 Edge   usb-001:005:01However, once the cable is connected and rebooted, the ip is normal and the communication is normal.Connecting usb LAN7850 to ubuntu x86 works fine.When the cable is disconnected, the usb interrupt does not seem to be transmitted normally. What is the problem?Any solution?Fix lan78xx.c or microchip.c

I'm now trying to read OTP 13~15 from remoteproc driver to enc/decrypt m4 firmware.From NVMEM overview. I learn below informationOTP 13~15 are non-secured area​The name of device is "stm32-romem0"NVMEM kernel APII can successfully get OTP 13~15 from user space.To get OTP 13~15 in linux kernel I write code that read nvmem device with the NVMEM kernel API.I define a match function​​int rproc_nvmem_match(struct device *dev, const void *data){ const char *device_name = dev_name(dev); const char *p_name = data; int length = strlen(p_name);​ if (memcmp(p_name, device_name, length) != 0) return 0; return 1;}​​Then, use nvmem_device_find and nvmem_device_read to read OTP 13~15. ( I use offset both 0x5C005234 and 0x234. )​ u8 *buf_uniqueId; buf_uniqueId = kmalloc(24, GFP_KERNEL); struct nvmem_device *nvmem = nvmem_device_find("stm32-romem0", rproc_nvmem_match); int err = nvmem_device_read(nvmem, 0x234, 24, (void*)buf_uniqueId); if (!nvmem) printk("nvmem error"); printk("err : %d", err);​But I

Hi, I would like to set all 8 pins in port Z to unsecure so i use these pins as other ports. I read data sheet portz is set to secure mode as default after reset. And I tried write into it and system crashed.Thanks

I am currently developing using STM32mp157fad and have a question. Here are the steps I have taken:Used STM32CubeProgrammer to upload the stm32mp157f-ev1 image to an SD card.Used STM32CubeMX to configure the GPIOs to be used with stm32mp157fad, generated code, and copied the device tree generated by the code generator to the SD card with OpenSTLinux installed.I'm wondering if this method is valid for use. If this is not the correct approach, I would like to know more information.

I am using UART over RS-485 on an STM32MP153AAB3.The communication fails because the actual baudrate is off from the specified baudrate. With a specified baudrate of 9600 Bits/s, I am getting an actual baudrate of 9970 Bits/s, as you can see here (time per Bit is 100.3µs instead of 104µs): Changing the baudrate to 115200 Bits/s results in a time per Bit of 8.33µs, i. e. 120000 Bits/s: I set the USART2,4 Clock in the .ioc file to 64 MHz and chose PCLK1 as the source.The value in the BRR register is 0x1A0B which, if I understand it correctly, should correspond to a value for USARTDIV of 416, giving a baudrate of 9615 Bits/s (64,000,000/(16*416) = 9615). My settings are as follows:static void MX_UART4_Init(void) { huart4.Instance = UART4; huart4.Init.BaudRate = 9600; huart4.Init.WordLength = UART_WORDLENGTH_8B; huart4.Init.StopBits = UART_STOPBITS_1; huart4.Init.Parity = UART_PARITY_NONE; huart4.Init.Mode = UART_MODE_TX_RX; huart4.Init.HwFlowCtl = UART_HWCONTROL_RTS; hua

Hello, I use Optee on a stm32mp157f-dk2 board, version is the and the corresponding BSP :optee-os 3.16.0-stm32mpu-boot v2021.10-stm32mpLinux v5.15-stm32mpAll my changes are committed and built using a yocto meta-layer : https://github.com/embetrix/meta-stm32mp15xthe Optee build config is described here : https://github.com/embetrix/meta-stm32mp15x/blob/kirkstone/recipes-security/optee/optee-os-stm32mp_3.16.0.bb#L33I enabled the PKCS11 TA which is by the way not by default enabled and gave it a try:EC Prime256 Keypair generation:# time pkcs11-tool --keypairgen --key-type EC:prime256v1 --label "testkeyEC" --id 1 --login --usage-sign --module /usr/lib/libckteec.so.0 Using slot 0 with a present token (0x0) Key pair generated: Private Key Object; EC label: testkeyEC ID: 01 Usage: sign Access: sensitive, always sensitive, never extractable, local Public Key Object; EC EC_POINT 256 bits EC_POINT: 044104d7506303c183c36445ef2d5161a5cfe1effaeb12a7b41ef458bc27811d2ddd915518917cd385ec35720324

I want the cortex-m4 to do pwmget data from sensors and transfer to cortex-A7So, I write simple code to do PWM and find out the RCC in stm32cubeIDE not work because linux take control the clock config.My question is, What is the best way to configure clock In my situation.Is it better to modify clock on linux command? or would it better to modity it in device tree?and where can I find the manual to modify it on devicetree?Thanks

Hi,I try to connect ADC channels with libiio for my custom board based on the stm32mp157caa3. I followed the instructions from the linkhttps://wiki.st.com/stm32mpu/wiki/IIO_libiiohttps://wiki.st.com/stm32mpu/wiki/ADC_device_tree_configuration#DT_configuration_examplesbut without success. After issuing the consoleiio_infoI getLibrary version: 0.23 (git tag: 92d6a35) Compiled with backends: local xml ip usb serial IIO context created with local backend. Backend version: 0.23 (git tag: 92d6a35) Backend description string: Linux stm32mp1-connect-bridge 5.15.67 #1 SMP PREEMPT Thu Sep 8 10:32:54 UTC 2022 armv7l IIO context has 2 attributes: local,kernel: 5.15.67 uri: local: IIO context has 0 devices:The same is in /sys/bus/iio/devices/empty, with no devices.Part of my dts looks&adc{ pinctrl-names = "default", "sleep"; pinctrl-0 = <&adc_pins_mx>; pinctrl-1 = <&adc_sleep_pins_mx>; status = "okay";   /* USER CODE BEGIN adc */ vdda-supply = <&vdda>;

Hi,​I upgraded the image for our custom board to 4.1 last week. After fixing the sw issuesconcerning the recipe syntax changes i have now problems to boot the new image.​Info: Our board does not use PMIC but static voltage configuration:​/ { model = "DEWETRON NEXDAQ tf-a"; compatible = "st,stm32mp157f-nexio", "st,stm32mp157";   aliases { serial0 = &uart4; serial1 = &usart1; serial2 = &usart2; };   chosen { stdout-path = "serial0:115200n8"; };   /* Supply Voltages */ vddcore: vddcore { regulator-name = "vddcore"; regulator-min-microvolt = <1200000>; regulator-max-microvolt = <1350000>; regulator-always-on; };   vdd: vdd { regulator-name = "vdd"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-on; };   v3v3: v3v3 { regulator-name = "v3v3"; regulator-min-microvolt = <3300000>; regulator-max-microvolt = <3300000>; regulator-always-o

Can ST please provide a guide for bringing up a custom board without using the STPMIC? We are extremely space constrained and unable to fit the PMIC. For our use case we just want simple LDO's with bucks as required.There is no material I can find that outlines what the device tree should look like for TF-A, U-Boot and Kernel when STPMIC is omitted.

We are bringing up a custom board with LPDDR2 and no STPMIC. I have been following the bring up guide and have gotten past disabling I2C4 and fixing the HSE clock issue in the device tree. I have merged in quite a few things from dev kit 'working' devicetrees as well.I am stuck at the following TF-A error though.Data Abort at: 0x2fff3e20 DFSR = 0x00000206 DFAR = 0x3664647fAbort at: 0x2ffe93a0I have used devtool to modify the tf-a recipe and increase the DEBUG level but nothing I do makes any difference. I just get this error.Attached is the flattened ftd from the TF-A build dir along with the cubemx generated set of devicetrees for tf-a.

I am puzzled with a curious build problem:The recipe gcc-arm-none-eabi-native downloads gcc-arm-none-eabi-10.3-2021.10-x86_64-linux.tar.bz2 but the download finishes to early (at 100MB instead of 150MB). Therefore the checksum check fails.BUT:If I copy the SRC_URL:SRC_URI = "https://developer.arm.com/-/media/Files/downloads/gnu-rm/10.3-2021.10/gcc-arm-none-eabi-10.3-2021.10-x86_64-linux.tar.bz2;name=gcc-arm-x86"into a browser or use wget the download completes successfully. Also the sha256 sum is correct then.Anyone experienced similar problems? Currently I will try to add a bbappend recipe to inject the archive as local file.My systems:Ubuntu 22.04 LTSAlternatively docker container with 22.04BB_NUMBER_THREADS="16" PARALLEL_MAKE="-j 16" bitbake gcc-arm-none-eabi-native NOTE: Started PRServer with DBfile: /home/glaure/Development/SW_APP/nexio_tmp/ost-5.15/build/cache/prserv.sqlite3, Address: 127.0.0.1:41099, PID: 1439493 Loading cache: 100% |#############################################

Datasheet says STM32MP15xx has ADC but here seem no ADC.​I am not sure if I am missing something.​

We can use devmem to read/write all gpio port registers except for portZ.We know this port relates to secure. is there any way to remove secure feature on this port so we can use devmem on this port?Thanks

gtk-launch: error while loading shared libraries: libEGL.so.1: cannot open shared object file: No such file or directory.

Hey,I was able to successfully flash the Starter Package following this article and after building the OpenSTLinux distribution following this, I'm having trouble with flashing it. After completeing the build process, inside the flashlayout_st-image-weston, there are 3 folders optee, extensible and deleteall. I was looking for trusted folder like in starter package but it is not available. Then I tried to follow article found here with cube programmer interface and through terminal with FlashLayout_sdcard_stm32mp157f-dk2-optee.tsv but i'm getting following error.Error: failed to download Segment[0]   Error: failed to download the File   Error: Download partition 0x05 failed   Error: TSV flashing service failedAfter that I tried to flash with FlashLayout_sdcard_stm32mp157c-dk2-optee.tsv in Starter Package but it also showed the same issue. I have attached the cube programmer terminal output. Apreciate if anyone can help me with this.Thanks.

I'm using a custom stm32mp157a board with a DSI display.If I enable uart8 using pins J8 (UART8_TX) and J9 (UART8_RX) the display driver (panel-sitronix-st7701.c) doesnt load properly and the display stays blank. uart8 does work properly. If I disable uart8 the display works again.

We recently udated from OpenSTLinux v2.1 to v4.1. The boot chain is solid, but occasionally we are getting TEE aborts (trace listed below). I am not sure exactly how to debug this, any help would be appreciated. E/TC:1 E/TC:1  Core data-abort at address 0x2fff8805 (translation fault) E/TC:1   fsr 0x00000207 ttbr0 0x2ffd8020 ttbr1 0x00000000 cidr 0x0 E/TC:1   cpu #1         cpsr 0x000001f3 E/TC:1   r0 0x2fff8805     r4 0x2ffda889   r8 0x2ffda889  r12 0xffffffe0 E/TC:1   r1 0x2ffcda91     r5 0x000000f7   r9 0x00000000   sp 0x2ffda788 E/TC:1   r2 0x2fff8805     r6 0x00000000  r10 0x2fff8805   lr 0x2ffcb297 E/TC:1   r3 0x2fff8806     r7 0x2ffda870 &n

Hi there, I am building custom board with openstlinux distribution package with following configBuild Configuration:BB_VERSION          = "2.0.0"BUILD_SYS           = "x86_64-linux"NATIVELSBSTRING     = "universal"TARGET_SYS          = "arm-ostl-linux-gnueabi"MACHINE             = "stm32mp1-silico"DISTRO              = "openstlinux-weston"DISTRO_VERSION      = "4.0.4-snapshot-20230428"TUNE_FEATURES       = "arm vfp cortexa7 neon vfpv4 thumb callconvention-hard"TARGET_FPU          = "hard"DISTRO_CODENAME     = "kirkstone"ACCEPT_EULA_st

Hello ,I want to build android distribution for STM32MP157F-dk2.ST-Android delivery only support STM32MP157C-EV1 and STM32MP157F-EV1 Evaluation board (aosp_eval).how can i create my own distribution for STM32MP157F-dk2 target

Hello,I would like to setup environment for STM32MPU according this instruction:https://wiki.st.com/stm32mpu/wiki/Getting_started/STM32MP1_boards/STM32MP157x-DK2/Develop_on_Arm%C2%AE_Cortex%C2%AE-A7/Install_the_SDKso I downloaded the SDK .tar https://www.st.com/en/embedded-software/stm32mp1dev.html#get-software/SDK-x86_64-stm32mp1-openstlinux-5.15-yocto-kirkstone-mp1-v22.06.15.tar.xzand run the script and got an error ./st-image-weston-openstlinux-weston-stm32mp1-x86_64-toolchain-4.0.1-openstlinux-5.15-yocto-kirkstone-mp1-v22.06.15.sh   Extracting SDK............................................................................................................................................................................................................................done Setting it up...xargs: file: No such file or directory sed: no input files Failed to replace perl. Relocate script failed. Abort!I run this script in docker based on ubuntu. All necessary packet installed. FROM u

Hello,I’m using an ST MP1 Development Kit STM32MP157C-DK2 to develop and deploy projects involving Machine Learning on an SoC.I need to perform some pre-processing operations on data coming from different sensors and to do so I have at my disposal Python scripts with dependencies from libraries like NumPy, Pandas, SciPy, and Librosa.While the first ones can be easily resolved by installing them via apt, (python3-numpy and python3-pandas), I’m encountering difficulties with the other ones (scipy and librosa), which are not available on ST repositories.I tried installing them via pip3, but it requires a compiler to build both libraries and dependencies from scratch, and the current Linux image I’m using doesn’t include it.Do you have any ideas on how to proceed, to help me?Thank you,Andrea.

I could not find any information relates to vbat battery charging in user manual or datasheet.​Is this feature supported in STM32MP15x?Thanks,​​​

I have two boards stm32mp157f-dk2 and my custum board(embedded stm32mp157d).I know that the difference stm32mp157f and stm32mp157d is simply security part.And my custom board don't have C-type connector because of issues in parts supply.So, After plugging the sd card into the stm32mp157f-dk2, I flashed the flashlayout dedicated to stm32mp157d via the stm32cubeprogrammer.And then, does it boot if I put the sd card back on the custom board?I've been looking for a reason why my custom board hasn't booted for weeks...What we've seen so far from the cmd and DAT0 signals on the sd card is that the initial cmd signal has the same logical level, and the DAT0 signal is slightly different.​I'd appreciate it if you could let me know.Thank you