Automotive and Transportation

I want to use DMA to transfer messages received from CAN. However, there seems to be no information in the datasheet about this feature, except for the illustration below. According to this image, it seems like using DMA for CAN is a default feature. However, I cannot find any settings related to CAN with DMA in SPC5Studio. Could you provide me with more information on how to use DMA for CAN? Is there any sample program available? 

Dear All,  I purchased this board for testing and development of the BMS. When i installed the NI products and the serial port driver. When i opened the GUI SW , again its asking the NI vision is not installed. Could you send how to link both the GUI and the NI SW whether there is anything i am missing during the switch ON process . 

with PLS JTAG and UDE STK 5.2 to debug SPC563M board,i cannot link to the board rightly,why?  

I am currently developing UART functionality on the SPC58EG chip, and I want to use LinFlexD1 hardware channel to develop UART.However, I cannot find relevant examples in the SPC5 Studio IDE.I am referring to the official manual (RM0391), which mentions that the Peripheral Sensor Interface-Support module (PSI5-S) must be enabled and related registers modified to use LinFlexD as UART.Are there any more specific example codes or projects that can be used as a reference for developing UART?Thank you.

I want to use DMA to transfer messages received from CAN. However, there seems to be no information in the datasheet about this feature, except for the illustration below. According to this image, it seems like using DMA for CAN is a default feature. However, I cannot find any settings related to CAN with DMA in SPC5Studio.Is it possible to access dma to all can communication channels on spc5?Could you provide me with more information on how to use DMA for CAN?Is there any sample program available? <li-image width="400" height="400" alt="tuananh13_0-1720608916844.png"

For your information , StellarStudio 6.0.0-IRON version is officially pushed (for SR5x & SR6x). (Windows, Macos, Linux) based on eclipse 202309 and the version CDT 202309 with its standalone tools https://www.st.com/en/development-tools/stellarstudio.html StellarStudio Pinmap (SR5E1), Clocktree (SR5E1) (Windows, Linux, MacOs)   StellarESDK-1.7.0 (SR5X) and TOOLS-1.4.0 with Git Bash Eclipse Integration / Update site system. with eclipse project creation wizard based with multiple sdks support (Integration of ESDK 1.7.0,ESDK-1.6.0,ESDK-1.5.0) with new pinmap wizard with board selection mechanism with CDT / embedded cdt / Openocd debug Integration with Migration tool from Old Pinmap to New Pinmap model Compliant with TRACE32 Lauterbach / ISYSTEM / Segger J-Link / Openocd. What's new in this release ? -SR5E1:                         Integration of Stellar ESDK

hello, I had read the "um3201-getting-started-with-stellar-studio-ai-plugin-for-artificial-intelligence-ai-stmicroelectronics" document, where can I find the AI Editor software to be launched like in page 5 ?Best regards, Laurent 

Hi,I've just gotten a new microcontroller SPC58EC-DIS from elfa. From my past I worked a lot with STM so I wanted to try something new, but this was the first time that I got something like this:Is it normal that the board comes with soldered wire between components SB28 and SB29 or is this something that I should report to the supplier? BR,MaraLo 

Hi ST Community,There is no software provided for the SPC5 47s 64E3 like low level drivers for the Controller.

Stellar SR6 G7 line : Where can get SR6G7C6 Steller Need Technical reference manual please

I am attempting to get the GHS compilier to build with SPC58NG dev kit and have switched the Build settings to below  I have updated the project to include the path and commented out the error statementifeq ($(GHS_PATH),)export PATH := C:\ghs\comp_202114\$(PATH_SEPARATOR)${PATH} # $(error Please specify a valid path into GHS_PATH for ccppc (GHS) compiler)endifand it will compile but then include some strange error that doesn't really help. Is there any setting I need to fix it looks to be something in the linking process.

I have completed implementing the Bootloader code in the SPC582B60E1 microcontroller.But for test cases, when the first code is succesfully uploaded via CAN and when I upload the second code, and if there is any connection error, and the communication breaks, the previous code is completely erased. What need to be done to retain the previous code for in the controller memory as for a backup plan?Please guide.

Hi all,I am facing issue with Open Load detection in PLAY mode and it is working fine in MUTE mode.I have flashed and tested  the example base code from STM(Autodevkit), Open Load Detection is not working in PLAY mode in this code(Placed the example code snippet below). In MUTE mode, If either or both speakers are disconnected the signal is updating with value FAULT_OPEN_LOAD_MUTE as shown below-In PLAY mode, If speakers connected or disconnected also both both conditions the value of signal is updated with "NO_FAULT_PLAY" as shown below-The structure member "OPENLOAD_PLAY" of structure "FDA_Errors_t" which is getting value from the registers is itself not updating during PLAY mode.Can anyone help me to come out of this issue. Thanks,Aishwarya UM

Hi,The BOM and almost all pictures of X-STM32MP-GNSS2 include a Taoglas antenna.Could you verify if an antenna is actually included or not, if I order an X-STM32MP-GNSS2?

Hello everyone, I am Erdem.I am trying to use FlexCan with the SPC560B-DIS development board. I ran the example project "SPC560Bxx_RLA CAN Test Application for Discovery," but I didn't want it to operate in LoopBack mode. When I disabled the LoopBack mode, I couldn't read anything from the PeakCan cable. I created a new project from scratch and wanted to send a simple CanBus message, but there was no communication. I am sharing the settings and code from my project in the images. I would be very grateful if you could help. Thank you.    

Hello, I have a question. Regarding waking up the system from LOW POWER mode, I want to use the WKPU but not with a push button as in the example.  Instead, I want to use a GPIO port to monitor an external signal. I want to use a rising edge interrupt. I cannot use INT18 because it is connected to a push button and the signal pin is always connected to VCC.  Therefore, a rising edge cannot be achieved.

hi community,           i had been working for a while on AEK-AUD-C1D9031 with CAN protocol and everything is working fine. but when i was working with open load of the speaker. in MUTE mode CAN message is working fine but in the PLAY mode the CAN message is not UPDATED, even the structure is also not UPDATED.         can any know the reason behind it.regardsshiva

Hello therei have maserati levante modena 2022 SUV and it’s totally flooded.BCM also totally damaged.BCM mcu is ST spc5605bmlu6.I couldn’t find any application to read and re-write this mcu.does anyone know what is the best tool to do this operation?thanks

Are there some tool like STM32CubeMonitor for SPC5 microcontrollers? With STM32CubeMonitor it is possible to load an elf or out file and watch variables values using gui components like gauge, bar, etc...

Hi everybody： My Board use the chip SPC560P50L3,and my application use the module flexray, and I have some questions: I use the demo example ,2 node can communicate very well, but I use one node communicate with other cluster,no matter the channel A or channel B, I always don't recv or trans the data from the bus, the poc state always is FR_POCSTATE_STARTUP, do not enter FR_POCSTATE_NORMAL_ACTIVE, how can I do to fix it? And how can I adjust the application to adapt any cluster? OR how can I know every cluster's global config or protcol config? Is ONLY from the DEVELOPER OR manufacturer get them? OR there have some protocol I dont know?

Here is what I've done: When my microcontrollers receives a sleep request from CAN, it goes on StandbyMode as shown below: Fisrt I disable CAN peripherals: can_lld_stop(&CANDRIVER1); can_lld_stop(&CANDRIVER2); Then I disable clock and interrupts: SPC5_PIT0_DISABLE_CLOCK(); SPC5_CAN_SUB_0_M_CAN_1_DISABLE_CLOCK(); ...... irqIsrDisable(); Finally it enters in STANDBY_MODE: if(SPCSetRunMode(SPC5_RUNMODE_STANDBY0) == CLOCK_FAILED) { SPC5_CLOCK_FAILURE_HOOK() }It wakes up when I apply a 5V on wake_up pin.Before doing all this procedure, I have already written some data to internal SRAM.Now when my microcontrollers wakes up, all SRAM's data are lost. I have tried two methods: 1) I modified the linker's file as shown, in order to reserve 4 bytes for my new backupsram : MEMORY{.... ram : org = 0X400A8004, len = 192k - 64k backupram : org = 0x400A8000, len = 0x04.....}//define size, start, end ( for example __backupram_end__ = ORIGIN(backupram) + LENGTH(backupram);SECTIONS {.......sta

hi i am new to the controller, i read the manual that dcf records contains the configurations like if device boots up it performs some basic tests and then basis on the application address provided in dcf record, it jumps to application, but that address is empty in my case, i want to program it to my application entry point, please tell me how to do this

Hello,I'm trying to start new project which is AVAS PRJ with SPC582B. So, I'm studying it with ST EVK like below.Anyway, When I check pin mode in AutoDevKitStudio, I don't understand exaclty the meaning of pin modes(MODE_IO/MODE_GPI/MODE_OUTPUT/MODE_INPUT/MODE_PI/MODE_EIRQ) like below red circle. Could you let me know about the pin modes??Thanks, 

Hello Community... We are working on a project for the automotive area and one of the requirements is that the circuit is powered by a voltage of 5V. We will also have analog inputs that should read values ​​between 0 and 5V. Reading the Reference Manual, we found the "CFlash Nonvolatile User Options register (NVUSRO)" which, according to our understanding, should have its PAD3V5V field written as 0, but we don't know exactly how to change/program the value of this register.On our board the VDD_HV and VDD_HV_ADCx voltages are supplied by 5 volts.All the board's peripherals (CAN/UART/Digital I/O, etc.) are working properly, however, when we put a voltage of 5 V on the pin used as ADC (PF[0],PD[13],PD[14] or PD[15]) it is crimped at a maximum value of 3.4V.Could anyone help us better understand the reason for this maximum voltage at the ADC input and also the procedure for writing to NVUSRO? Thanks in advance.

Hi,      I need LIN driver library files for SPC584B70E5 microcontroller, please do the need full. Thanks.