Automotive and Transportation

I'm trying to download SR6G7 elf code into internal Flash. So far this MCU seems to be not directly supported from the StellarStudio (?).Is there a way of programming my board using StellarLink from the command line? I found a working solution for other chip (like SR5E1):C:\StellarStudio-2.0\openocd\bin\openocd.exe -d0 -s C:\StellarStudio-2.0\openocd\scripts -f board\sr5e1_evbe7000p.cfg -c "program blinkled_portE13.elf reset exit"However, there are missing SR6G7 configuration files in the latest StellarStudio_rev4.1 and StellarLink releases. The one defining target board I could prepare myself, yet the other describing SR6G7 chip and FLASH_ERASE algorithms are not available.Can someone worked already with that chip and could share the proper config files (chip and algo)?  

We are implementing application software in performance core. So, we are bound to do FMEDA analysis,  *   Is there a FMEDA analysis performed in SPC58xNx hardware from your side?  *   All failure detections which are carried over in performance cores (core which doesn't have lock step core).  *   Self-test, core monitoring and logical monitoring is done for all the cores?May I get any documents related to failure analysis for this micro-controller.If there are any documents from your side, then it would be easy for us to proceed further.

Hi,I have a EVB-LIV4F. I would like to know how to enable RTCM message. I would like to extract the following raw measurements from RTCM:1) the time of the measurement2) satellite pseudoranges measured between the satellite and GNSS receiver3) their standard deviations4) carrier phase5) Doppler shiftsThanks.

Yet another step with AutoDevKit. In the latest version 2.6.1, you shall find a dedicated GUI for monitoring of your BMS system, including voltage, current and temperature readings and SoC.

Is a document available that defines all the configuration data blocks for the LIV4F?  We are specifically looking for the contents of configuration data block 263, which seems to configure the I2C interface.

Good morning everyone On the https://www.st.com/en/embedded-software/stsw-autodevkit.html, the en.stsw-autodevkit.zip file is not opened properly. I tried winrar and 7zip file manager, but it results in an error when opening the compressed file. How can you help me? I didn't even find a previous version downloadable to buffer. Thank you.

Hello, I am interested in the Stellar E and P series for the purpose of motor control, with an inverter topology that has 12 independent switches and requires fine control of the offset between some of the waveforms.1) The E series is marketed as optimized for traction inverters. Is there anything it can do in power converter applications that the P series cannot do? Does E series do something better or more easily, or just cheaper?2) Is there any difference between the HR timer peripherals of the E and P series, except that E has 2 x 6 channels and P has 2 x 8?3) How does the GTM4 of the P series compare to the advanced control timer of the E series? I can't find information about GTM4 on the product pages.4) Is it correct that the E series does not have any interface for external RAM, not even quad SPI?5) In the datasheet for E series, page 38, https://www.st.com/resource/en/datasheet/sr5e1e3.pdf, what is the meaning of the specification f_IN = 0.01 kHz minimum? Can it not convert th

 I have some problem with DR mode.I can't recieve any $PSTMDR2 or $PSTMDRCAL messages, so the status of DR remains unknown.But I checked the CDB 228-230 with $PSTMGETPAR, the following are the response.========$$PSTMSETPAR,1228,0x00000000*5A$$PSTMSETPAR,1229,0x6cc22000*5D$$PSTMSETPAR,1230,0x00000000*53==========In CDB 229, bit 60-63 is 6, meaning that the $PSTMDR and $PSTMDRCONFID are enabled, but I can only see $PSTMDRCONFID. There are no $PSTMDR message there. Are there any problem with my configurations?Also, I had enabled these messages in CDB 229, meaning that these message should be update in 10 Hz. But it still be updated in 1 Hz, as following.==========$$PSTMDRCONFID,0.00,0.00,0.0000,0.0000,0.00,0.0000,0.000000,0.000000,0.0000,0.0,0.0,-0.0,0.0*1A$$PSTMDRPVA,162640.000,2945690305,37.5517719,14.2984835,730.1,0.00,0.00,0.00,0.00,0.00,0.00*57$$PSTMDRCONFID,0.00,0.00,0.0000,0.0000,0.00,0.0000,0.000000,0.000000,0.0000,0.0,0.0,-0.0,0.0*1A$$PSTMDRPVA,162641.000,2946713305,37.

I've got the CAN Test app loaded and working as it should. I'm trying to get it to transmit out instead of loopback. I've already uncheck the option for loopback and simplified the code to only transmit. However, I don't see any activity on the CAN pins of the board. I've tried moving the jumpers from CAN0 to CAN1 and I've tried looking at the signal before the transceiver but still nothing. My code is attached below. Any help would be greatly appreciated!#include "components.h" #include "can_lld_cfg.h" /** * FLEXCAN Error callback. This is kept for good practice but is not essential * for transmitting. */ void cfg0_errorcb(CANDriver *canp, uint32_t esr,uint8_t rx_err_counter, uint8_t tx_err_counter){ (void)canp; (void)esr; (void)rx_err_counter; (void)tx_err_counter; } /** * FIFO notification callback. This is no longer used since we are only * transmitting messages. */ void cfg0_Fifo_RX(CANDriver *canp, CANRxFrame crfp) { (void)canp; (void)crfp; } /* * Application entr

Dear STMicroelectronics Support Team,We are currently working on a project involving the AEK-POW-BMSWTXA board, which we are interfacing with an STM32F405RGT6 microcontroller via SPI communication.We have connected the board over SPI, but we are not receiving any response from it. To proceed with our development, we kindly request the following:The official User Guide or any detailed documentation for the AEK-POW-BMSWTXA board.A working SPI communication example for interfacing this board with an STM32 MCU (preferably using STM32 HAL).Guidance or sample code to read individual cell voltages from the board.          Thank you .

Dear STMicroelectronics Support Team,We are currently working on a project involving the AEK-POW-BMSWTXA board, which we are interfacing with an STM32F405RGT6 microcontroller via SPI communication.We have connected the board over SPI, but we are not receiving any response from it. To proceed with our development, we kindly request the following:The official User Guide or any detailed documentation for the AEK-POW-BMSWTXA board.A working SPI communication example for interfacing this board with an STM32 MCU (preferably using STM32 HAL).Guidance or sample code to read individual cell voltages from the board.We are facing difficulty in establishing communication and would appreciate your support in resolving this issue.          Thank you .

Hello everyone,I'm working with SPC58 microcontrollers and configuring 6 PWM channels using different eMIOS. The PWM channels within the same eMIOS are properly synchronized, but the channels from a different eMIOS are not synchronized as expected.I have attached a figure illustrating the issue. How can I configure the PWM channels from different eMIOS to ensure proper synchronization? Are there specific settings or registers I should adjust?Any insights or recommendations would be greatly appreciated.Thank you in advance!#define kPWM_PWMPERIOD (5000U) /* 50% */ #define DEADTIME_BASE (10U) #define DELAY_BASE DEADTIME_BASE / 2 void PWM_start(PWMDriver *pwmp, PWMConfig *config) { pwm_lld_start(pwmp, config); } void PWM_setDutyCycle(PWMDriver *pwmp, pwmchannel_t channel, pwmcnt_t width, pwmcnt_t deadTime, pwmcnt_t delay) { pwm_lld_enable_channel(pwmp, channel, PWM_PERCENTAGE_TO_WIDTH(pwmp, width), deadTime, delay, 0); } void PWMConfig(void) { PWMconfig[kWH1_ID] = (PWM_Config_t){&am

Could I have the BSDL file for the SPC560B50L1C6E0X. Thank you!

Hello! In the SPC58XX-RLA PWM-ICU Test Application for Discovery routine, I would like to ask which CH0 is circled in red as shown in the following figure, CH1... What do they represent? I have been confused whether eMIOS0 CH0 in the first image and Channel 0 in the Channel 0 Setting in the second image are the same channel. I hope you can give me an answer! Thank you!

Just got an SPC560P-DISP and I'm following AN4487 Getting started instructions. I have the board connected via USB to my computer and I've got SPC5Studio up and running with a Serial Test App. I have cleaned, generated and compiled the app. Following along in the guide, opening the debug.wsx doesn't open a new window but rather the file itself in eclipse. The "Execute and debug your application" action is also grayed out. I've tried installing "udestk-5-02-04-spc5-stk" and CDM2123620 FTDI drivers.After the "udestk-5-02-04-spc5-stk" was installed, in Device Manager, it went from a driverless device to PLS USB JTAG Adapter for SPC5xxx A/B. I've opened UDE STK independently of SPC5Studio and opened the debug.wsx file. This seems to allow me to flash a program to the board. I wanted to try and see if I could connect via Serial but there were no open COM ports from the device itself. After unplugging and plugging back in the board, it goes back to the LEDs blinking program the boa

I'm using the Teseo-LIV3F module in my project, and I want to receive NMEA messages at a higher frequency than 1 Hz. Is there a command to set the message output rate to 500 ms?

what`s wrong?my spc5studio shows 

Hello Team, I am currently utilizing the SPC58EC Microcontroller in an Autosar project where I have set up the CAN MCAL driver for both Tx and Rx operations in interrupt mode. We have noticed that whenever the system bus experiences a sending bus load of around 13%(FD and Normal CAN messages are present), the CAN controller which is supported with FD configuration enters a Bus Off state, and this appears to be an intermittent issue . We have two channels configured: one for FD and the other for standard CAN message transmission, with the sample point set at 80%. When the same software is executed without 2 to 3 necessary messages, the Bus Off state does not occur. SBC TLE 9271 is used as Can Transceiver

When using the StellarLink programmer to program the SPC58NH92E7 chip, the following issues occur.What can i do?I really need your help! 

Hello,​I've been looking for a debugger to debug and program an SPC58xx MCU and I've found you offer both the new Stellarlink and the SPC5-UDESKT. I understand the SPC5-UDESKT requires a licence to be used with the Universal Debug Engine (UDE) which are available as either a year licence or a one-time purchase. I was wondering if I would also need one of these licences to use the Stellarlink with the UDE/SPC5Studio? It looks like the Stellarlink has more features supporting your Stellar Automotive line so would you recommend this for a new debugger/programmer purchase over the SPC5-UDESKT?Many thanks,Owen

HiNew kid on the block.Starting to dig into SPC58EC-DISP development board.While waiting for the board to arrive I wanted to see some code examples.Downloaded SPC5Studio from the SPC58EC-DISP site were it was said that demonstration files should be in found in the SPC5Studio installation. But they are not to be found.Anyone know were such could be located ? Kind Regards.

Hi, after i have downloaded the softare. I tried to monitoring a battery pack made up with 4 cells in series. When i open the GUI, only the first 3 cells are monitored the last one isn't monitored. Anyone have a solution or a schematic about the pin? Cause the gui guide says that the minimum configuration is cell 1,2,13 and 14. Thank you so much

I'm new to the LIV4F (I have a Teseo-LIV4F evalution kit), coming from u-blox. We have an NTRIP Client who delivers RTCMv3 data to the serial Port of the LIV4F, but the data seems to be ignored (the same data with a u-blox ZED-F9P is working fine). Do I have to enable the receiving of RTCM data in the LIV4F?

Hello, we are using Stellar SR6 controller in a customer control unit. We have received SDK v 4.4.1. But this does not contain the SENT Driver.  I had also downloaded the latest StellarStudio v7.2 from the ST website. This consists of drivers only for SR5E1. Is there any newer SR6 SDK that includes SENT driver? Or could I download it from the ST website myself? Also, is the SR5E1 SENT driver compatible with the SR6 SENT peripherie? Appreciate any response to my queries above.  Thanks!  

In the App Note, AN5949 "SR5E1 line - 7 KW EV/HEV on-board-charger reference design", there's a mention of "A dedicated Lauterbach script (SR5E1_multicoreAMP.cmm file) has been released to debug in AsymmetricalMultiProcessing (AMP) mode the main cores of SR5E1: Core_1 and Core_2." Can you please provide a link / attachment for where I can obtain this file.I'm trying to run multicore simple applications via a cmm script, but I'm unable to obtain a stable connection over multiple resets.Regards,Steven Daglish