Product forums

Hello I want support for STSPIN32G4 EMI Issue I took tests for Farfield EMI Report at STSPIN32G4 Standby conditionReport shows QP are over than Limit at 190.547MHz, 253.803MHz and I also get similar result by using Near-field prove(Proved Noise Peaks : 185.91, 123.94, 247.88, 309.84MHz) this result are same at evspin32g4-dual(also Flash Erase conditions results) I guess 62 MHz harmonic noise occurs between STM32G431 and STSPIN32G4 Internal Control logic Because I observe noise when Voltage input to VM and REGIN for the (in 3.3V externally supplied circuit) I want to know how could i solve this problem(Resolving EMI noise)

  I had some issues configuring H573 with CubeMX.When I configure TIM2 or TIM3 according to the instructions of RMII_PTP_Synchro in CubeMX I cannot enable the RMII PTP functionality.And when looking at RM0481 it seems that the description of the relationship between these two timers and ETH MAC is a bit vague.What configuration is required to enable RMII_PTP_Synchro on H573?

I am using MEMS Studio to evaluate FSM and MLC on the STEVAL-MKI109D + STEVAL-MKI238A . I noticed few strange things. I am attaching my FSM gui config and reg config (config.zip)1. When I open the FSM tab and load the state machine files and device configuration fileone thing I notice right away that its not loading the Long Counter Max value correctly.In my saved FSM configuration I have set it to 0x14 but when I load the configuration it still showing up at 0001Now when I click "Write FSM configuration to the sensor" button and head to Register Map tab, I do see 0x14This is very misleading as the FSM configuration tab is different value that is actually written to registers.  2. Next thing I notice is that when I load my FSM configuration and GUI files and click "Write FSM configuration to the sensor". Head to Sensor Evaluation and return back to Advanced features -> FSM. The FSM ODR now changes to 12.5 Hz.This is how FSM tab looks when I load gui and config fi

When I'm writing code, I often encounter problems caused by the "automatic #include feature".For instance, when I type "__HAL_TIM_SET_COMPARE()" into the code, the line "#include "stm32f0xx_hal_tim.h"" will be automatically added, and then the project will fail to compile properly.I suggest that the "automatic #include function" be set to be disabled.

Hi Forum! Previous experiments, but it still could not work, I have no idea how to fix this problem:https://community.st.com/t5/stm32-mcus-embedded-software/hmd-application-stm32f1-with-bno055-via-vcp/td-p/876235 Therefore, I revisited the literature review. I found this paper from meta oculus, they using the HID to transfer the IMU data, so I want to imitate their steps. (using notebookLm to learn it )https://msl.cs.illinois.edu/~lavalle/papers/LavYerKatAnt14.pdf HID read/write tool(software)https://github.com/benbaker76/SimpleHIDWrite  Problem: Custom HID could be detected by host, the IMU could send the data at 100Hz, host could send the data to STM32 MCU, but only the first time was successful, the second time will let the HID read/write tool(software) crash, STM32 could send data after receiving the data first time. ----------------------------------------------------------------------------------------------------------------------------------------------------------

On a custom STM32H523-based board connected via STLink 2.0 (swd, p2p in CubeMonitor), all selected variables are plotted as 0, including those whose initial value is not 0. I used the Basic_Flow template, where I set acq_out, acq_in, and loaded variable addresses from an ELF following this guide. The executable is proven to update values under GDB. I have tried rebuilding with -O0 and reconnecting and changing sampling frequency between sequential loop and 10 Hz. The code does not contain any standby instructions and the port looks fine since GDB works. I would appreciate any help or advice.

Hello,I am an engineering student working on my senior graduation project using the STEVAL-WBC2TX50 evaluation board. I need the STSW-WBC2STUDIO (or the updated WPSTUDIO) GUI to configure the board, but all official links on the ST website return a 404 error.Could you please provide a working download link or the installer files? My project exhibition is approaching soon, and this is a critical blocker.Thank you for your support.

When configuring the LEDs for the STM32H573I-DK using the STM32CubeMX it generated code which initializes the LED pins as PushPull (rather than OpenDrain).Lookign at the schematics of the STM32H573I-DK it seems to be not "the best option".Would you agree that OpenDrain (GPIO_MODE_OUTPUT_OD) is the better option here, rather than PushPull (GPIO_MODE_OUTPUT_PP)? /** * @brief Configures LED on GPIO. * @PAram Led LED to be configured. * This parameter can be one of the following values: * @arg LED1 * @arg LED2 * @arg LED3 * @arg LED4 * @retval BSP status */ int32_t BSP_LED_Init(Led_TypeDef Led) { int32_t ret = BSP_ERROR_NONE; GPIO_InitTypeDef gpio_init_structure; if ((Led != LED1) && (Led != LED2) && (Led != LED3) && (Led != LED4)) { ret = BSP_ERROR_WRONG_PARAM; } else { switch (Led) { case LED2: /* Enable the LED2 GPIO clock */ LED2_GPIO_CLK_ENABLE(); break; case LED3: /* Enable the LED3 GPIO clock */ LED3_GPIO_CLK_ENABLE()

I'm running Bazzite (Fedora 43) and tried to install STM32CubeMX on a Fedora distrobox and was met with some issues.First, the installer is unable use /bin/chmod, this is fixed by switching out the installer's `jre\bin` directory for OpenJDK.Second, if you run as a normal user it fails with:com.izforge.izpack.api.exception.IzPackException: An error occured in java.lang.Thread.run() at Thread.java:1583 in com.izforge.izpack.installer.unpacker.UnpackerBase.run() at UnpackerBase.java:241 in com.izforge.izpack.installer.unpacker.UnpackerBase.unpack() at UnpackerBase.java:319 Caused by: com.izforge.izpack.api.exception.InstallerException: File execution failed in com.izforge.izpack.installer.unpacker.UnpackerBase.unpack() at UnpackerBase.java:299 in com.izforge.izpack.installer.unpacker.UnpackerBase.unpack() at UnpackerBase.java:483 in com.izforge.izpack.installer.unpacker.UnpackerBase.executeFiles() at UnpackerBase.java:959This is fixed by running the installer via sudo.This is what I did

I have an old Ubuntu 18.04 system which allows STM32CubeIDE to run, but the STM32_Programmer failed because libm.so and libc.so were wrong. I found glibc-2.30 and copied the libraries into the same directory as the STM32_Programmer lib. Now I just get a seg fault, even when trying to just get the version number:bin/STM32_Programmer_CLI --version Segmentation fault (core dumped)Is there any way to figure out what might be the problem?   

Hello ST,I'm trying to communicate the STM32F411RET6 with IMP34DT05 mic, i have enabled the I2S in ioc configuration, i have downloaded and added the library file from https://www.st.com/en/embedded-software/x-cube-memsmic1.html, while building the project getting 15000+errors coming, i'm assuming this library file is incorrect, could you please review as attached and provide Specific working library for this project.Advance Thanks,Sridhar. 

Hello,I am currently working with the STM32WBA65RI for BLE Direction Finding using connectionless mode. I would like to know if it is possible to use a low-power mode such as Standby with RTC, allowing the board to consume only a few nanoamps, then wake up periodically via the RTC, perform advertising for a defined period, and return to Standby mode.Could anyone provide guidance or share experience with this approach?Best regards.

Hallo zusammen,mir ist im STM32CubeProgrammer (GUI, v2.19.0) ein merkwürdiges Verhalten im Automatic Mode aufgefallen:Wenn man den Haken bei "Run after programming" direkt aktiviert und dann auf „Start“ klickt, wird kein Reset ausgeführt, obwohl die Option gesetzt ist. Das Programm wird nicht neu gestartet. Wenn man schnell hintereinander viele Platinen updaten will mit Neustart des Programms ist dies hinderlichWorkaround:Wenn man den Haken einmal entfernt und dann wieder setzt, funktioniert der Reset im Automatic Mode anschließend wie erwartet. Offenbar wird die Option intern erst korrekt übernommen, wenn sie aktiv verändert wurde.Das Verhalten ist reproduzierbar und tritt unabhängig vom Ziel-MCU auf (getestet mit STM32L4 und ST-Link v3MINIE).:wrench:Vorschlag:Es wäre super, wenn das in einer der nächsten Versionen behoben werden könnte – vermutlich reicht ein Fix im Initialisierungsverhalten der GUI.Viele GrüßeBB-RTB Translation:Hello everyone,I noticed some strange behavior in

I have been programming my STM32H743 custom board for over a year.  Suddenly I'm getting the error message Error: No STM32 target found... I have tried changing the ST-Link itself but get the same error message.

Hello,I just created a new project for the STM32L542CEU MCU with CubeMX and I'm facing two issues with the imported project in CubeIDE.First issue, rather easy to fix, some path for includes files are missing in the project.Second issue, two include files are missing:Description Resource Path Location Typefatal error: ARMCM0.h: No such file or directory RTE_Components.h /CURRENT_SENSING/Drivers/CMSIS/NN/NN_Lib_Tests/nn_test/RTE/_ARMCM0 line 17 C/C++ Problemfatal error: irq_ctrl.h: No such file or directory os_tick_gtim.c /CURRENT_SENSING/Drivers/CMSIS/RTOS2/Source line 26 C/C++ Problemmake: *** [Drivers/CMSIS/RTOS2/Source/subdir.mk:25: Drivers/CMSIS/RTOS2/Source/os_systick.o] Error 1 CURRENT_SENSING C/C++ Problemmake: *** [Drivers/CMSIS/RTOS2/Source/subdir.mk:25: Drivers/CMSIS/RTOS2/Source/os_tick_gtim.o] Error 1 CURRENT_SENSING C/C++ Problemmake: *** [Drivers/CMSIS/RTOS2/Source/subdir.mk:25: Drivers/CMSIS/RTOS2/Source/os_tick_ptim.o] Error 1 CURRENT_SENSING C/C++ Problemmake: *** Wait

Hi everyone,I designed a first custom PCB using the BlueNRG-2N as a coprocessor, and everything was working fine, I was able to control it with my main MCU over SPI without any issue.Recently, I made a new version of the board where I replaced the BlueNRG-2N with the BlueNRG-M2SP module. I flashed it with the DTM firmware (BLUENRG-M2SP_DTM_SPI.hex) because I want to use it as a coprocessor.I’m using exactly the same software as before for my main mcu (which should work), but now it doesn’t work at all : I don’t receive any data on the SPI MISO line from the BLE module.I’ve attached both the old (working) and new designs. Since the firmware works with the BlueNRG-2N, I assume the issue is hardware-related. What could be wrong in my new design? Or what changes are required for the software ? Also, I have a couple of additional questions:1- There are multiple DTM firmware versions available (e.g. BlueNRG-M2SA_M2SP_DTM_Stack_v2.1c, v2.1e, and several others in the BlueNRG-1_2 DK 3.2.3

Added "DHCP" in the title to give the context. Using an STM32H7S78-DK I try to set up the network to join an IPv4 network through DHCP. I did set up the board using CubeMX, standard configuration, MPU activated. FreeRTOS + LwIP Removed all other interfaces I don't need. Made sure the Ethernet clock shows 50MHz The LED's on the RJ45 start to blink (Orange LED blinks with packets exchanged) but I get no IP address. digging in the possibilities I added a simple routine to monitor the DHCP advancements. struct dhcp *dhcp_data = netif_dhcp_data(&gnetif); if (dhcp_data != NULL) { printf("[DHCP] State: %d, Retries: %d\r\n", dhcp_data->state, dhcp_data->tries); } this shows I get stuck in state 6: waiting for an ACK -> what could be behind this? can someone share an .ioc file that sets everything correctly in MX?

I have an stm32 board connected to a raspberry pi.I am trying to start a remote debug session from StmCube IDE Installed on my computer and I get this error.I haven't encountered this problem before and I don't quite understand its cause because I have configured everything correctly :- in Cube IDE Debug Configuration I selected connect to remote GDB Server with correct host name and port 3333.- in the pi side I created an openocd.cfg file which includes "bindto 0.0.0.0" command in order to allow connections from any ip.

"I am currently working on implementing Ethernet communication using a NUCLEO-H753 board.As a first step, I attempted to perform a ping test. I followed the official tutorial videos provided by STMicroelectronics step-by-step, but unfortunately, I am not getting the expected results (the ping is failing).I would appreciate any guidance or advice on what might be causing this issue or which specific configurations I should double-check.""Let me share my CubeMX configuration with you first so we can review the setup."1. System Core - CORTEX_M7  2. Connectivity - ETH 3. LwIP 4. Clock I will also share the modified source code with you. STM32H753ZITX_FLASH.ld/* Modification start */.lwip_sec (NOLOAD) :{ . = ABSOLUTE(0x30040000); *(.RxDecripSection) . = ABSOLUTE(0x30040100); *(.TxDecripSection) . = ABSOLUTE(0x30040200); *(.Rx_PoolSection)} >RAM_D2/* Modification end */ ethernetif.c/* USER CODE BEGIN 2 */ #if defined ( __ICCARM__ ) /*!< IAR Compiler *

Dear Sir or Madam,  We would like to use NUCLEO-WL33CC2 to verify DMR RSSI reliable detection(compulsory requirement) and demodulation(optional requirement).  We only need rx chain for scanning purpose.  As per ETSI TS 102 361-1, DMR TDMA frame has sync word in the middle of 30ms frame and does not have preamble. And in Chapter 10.2.2.2 (Physical layer), an RRC filter is designed for 4FSK.  It seems these settings may not have corresponding option in STMWiseCube, so that we would like double check with you if there is any better setting for detect 30ms packet RSSI at least.  We do know the sync word content for DMR, which is 48 bit long. The modulation is 4FSK, nomial channel width is 12.5kHz, and data rate is 9.6kbps. And deviation is +/-0.648kHz and +/- 1.944kHz for 4FSK, shall we use 1.944kHz in the setting of deviation in STMWiseCube?   Our requirement is RSSI at room temperature for this TDMA frame detection in RF conducted test mode and without

Hello ST community, I configured my project in STM32CubeMX 6.17.0 and use STM32CubeIDE 2.1.1 to debug. The goal of the program is to receive a raw ethernet frame.I followed this tutorial, of course I adapted the pins to NUCLEO-N657X0-Q, and I skipped the part with the transmission, I didn't change anything in the HAL_ETH functions. I am sending from the PC (I can see that the frame is sended with wireshark):from scapy.layers.l2 import Ether from scapy.packet import Raw from scapy.sendrecv import sendp #Terminal ipconfig /all dst_mac = "00:80:E1:00:00:00" src_mac = "AA:79:39:37:92:EA" payload = bytes([0x01] * 86) frame = Ether(dst=dst_mac, src=src_mac, type=0x88B5)/Raw(payload) sendp(frame, iface="Intel(R) Ethernet Connection (13) I219-LM", verbose=True)I placed a breakpoint in :void HAL_ETH_RxCpltCallback(ETH_HandleTypeDef * heth) { }This callback should be executed when an Ethernet packet is received, but it never happened.I also tried by defining USE_HAL

Dear ST team.   I am testing UART of NUCLEO-WB09KE with the board [STM32WB09 Nucleo-64 board (MB1801 and MB2032)] I Set UART1 PIN PB4, PB4 with the source attached[100ms period tx send ]. I am checking CN3(23), CN4(35) but no signal shown. Is there anythn        

Hi all,In order to have two possible functionalities on the same M12 plug I need to multiplex the C/Q line of IO Link with an analog input signal. The device is configured before the connection is established and it should stay in that mode during the whole operation. Here is the basic idea:My first Idea is to use a latching relays. Do you think it could cause problems to take the IO Link signal over the relays? I have never before used a relays in a signal path (digital or analog) and I am not sure if it could cause trouble. My second idea was to just connect both signals together without an additional switch or something like that:But I couldn't find out, if the OUT and I/Q Pins can handle a voltage when there is no 24V supply at VCC. (24V is only present when there is an IO Link Master connected to the plug). The analog signal can be 4-20mA, 0-10V or PWM (24V). Could the L6362A handle this? Also would this maybe impair the accuracy of the analog signal measurement? I also have

In an Edge AI audio project that I'm working on, there is SAI2 peripheral that stops audio transmission after a while when the AI algorithm in the while loop of the main.c has done some inferences.The AI algorithm code was generated with Cube AI Studio and, when STM32CubeAI_Studio_AI_Process() is commented, the SAI peripheral works normally without interruptions.The board used is a NUCLEO-N657X0-Q.The version of software used is:-ST Edge AI Core: version 4.0.0-STM32CubeIDE: version 2.0.0-Cube AI Studio: version 1.1.0I've tried to search on internet for a solution and there is no material concerning it! I've tried to ask for help in other posts, but nobody helped me. Can somebody try to explain why and find a solution? I'm desperate and I don't know what to do for my project but withdraw. 

Hello everyone, I am using the NUCLEO-H755ZI-Q board for a project. I have noticed that the HRTIMs thatare not multiplexed with some USB pins (like the HRTIM_D1 with the D+ for programming the IC via usb)work normally, while if they do, I can't output any PWM pulse. Is this actually a thing and to overcome itI have to remove some of the Zero Ohm resistors behind the nucleo board or design a custom pcb for my needsor am I messing something up? In my situation specifically, i can output from all HRTIM channels except the D1and D2, both of which map to a pin with USB. Thanks in advance!