Product forums

reply from moderator

Hello

Hi,When using this, single-character text isn't perfectly centered on the button,the letter appears slightly higher.Also, characters like .,_ appear higher than they should.Is it possible to adjust the text position horizontally when using these? 

Ahla Test fel kayesEdit test

this is a random post to test new posts email notif

Hello all,I’m working with an STM32 microcontroller (specifically the STM32H743), and I have a question regarding the use of an external TCXO as the HSE clock source.As per the datasheet, when using an external clock source (such as a TCXO), the HSE must be configured in bypass mode, and the input clock is expected to meet the digital I/O thresholds (e.g., 0.7 × VDD for logic high). However, many high-quality TCXOs have typical output swings of only 0.8–1 Vp-p (clipped sine wave), which do not meet CMOS thresholds when VDD is 3.3 V.Therefore, directly driving OSC_IN with such a TCXO in bypass mode is not viable per the datasheet.That said, I made an observation I’d like to confirm with you:While using a crystal in crystal resonator mode (not bypass), I probed the OSC_IN pin using a low-capacitance active probe and measured a signal of approximately 1 Vp-p. Since this amplitude is generated internally by the oscillator circuit when using a crystal, it seems the STM32’s HSE input is desi

Hello, I am trying to load a kernel driver (.ko file) for a MIPI camera I would like to use with the STM32MP257F-DK. It's for the imx664, and no driver is present already. I have the source for the driver, and was able to compile it into a .ko file, cross-compiled with the exact same OS as is present on the board and with the SDK set up as required. The vermagic line matches exactly: vermagic: 6.6.78 SMP preempt mod_unload aarch64However, every time I try and load the driver with insmod, with or without -f, I get the error: insmod: ERROR: could not insert module imx664.ko: Invalid module formatI am struggling to find where the incompatibility could be, since I have re-tried it a few times and been careful to set it up as ST's documentation says and also to match what is expected by the board. Is there something I am missing with this?

The STM32L476 does not have an nBOOT0 option bit in its option bytes. Is there a way to boot from the main flash memory without using the BOOT0 pin?

The STM32G031G8U6 in a UFQFPN28 package does not have PF0 / PF1 pins for HSE OSC_IN / OSC_OUT.  It does however have OSC_IN on PC14.  This is intended for an external CMOS oscillator in bypass mode.I’m currently in the schematic design stage. My board clock is a clipped-sine TCXO used for other purposes.  In some modes, I’d like to use it to clock the STM32. I’m very constrained on cost, power, and board space.  The clipped-sine doesn't meet the voltage level requirements for a bypass-mode clock.Is it possible to configure HSE as if it were a crystal, but instead supply a clipped-sine 0.8 Vpp clock from the TCXO to PC14 OSC_IN? Does the die used in UFQFPN28 even have the HSE oscillator circuit that exists in the 48 pin package?I would set RCC_CR[HSEBYP] = 0 and RCC_CR[HSEON] = 1.  I don’t see any register controlling the OSC_IN alternate function on PC14.  STM32CubeIDE doesn't allow this configuration, unsurprisingly, but I would configure t

I'm developing using the STM32WBA65I-DK1. I'd like to know how to implement interrupt handling for button presses. It appears that stm32wba65i_discovery.h does not contain any APIs related to button presses (which is perhaps to be expected since the DK does not have push buttons). The sample code I'm using is BLE_HeartRate_Thread. If you have any source code that might be helpful, please let me know.

Hello everyone,I'm working with the STM32L562E-DK board and the STM32Cube_FW_L5_V1.5.0 firmware. I want to integrate my own code (which reads a sensor MPU6050 via I2C) into the STM32CubeL5 TFM (Trusted Firmware-M) application, running it in the Non Secure environment. The base project I'm using is TFM_Appli, which comes in the package, and I've added my source code to the NonSecure section.I created a separate project in STM32CubeMX using the board's I2C1, which utilizes pins PB6 (SCL) and PB7 (SDA). I ​​then generated the code and copied the I2C communication initialization code into the "main.c" file of my "TFM_Appli_NonSecure" project. Specifically:/* This is before "int main (void)"-----------------------*/ I2C_HandleTypeDef hi2c1;/*------------- I'm calling these function from "int main(void)" ------------*/ static void MX_GPIO_Init(void) { /* USER CODE BEGIN MX_GPIO_Init_1 */ /* USER CODE END MX_GPIO_Init_1 */ /* GPIO Ports Clock Enable */ __HAL_RCC_GPIOB_CLK_ENABLE(); __H

In STM32CubeIDE, I can compile C++ code in the project. The CMake file generated for the VSCode extension doesn't work with C++. Is there a way to use C++ code with less hassle than trying to get around this by hand?

I have an issue were the Linux kernel is booting, then it just stops printing out messages from USART6.Meanwhile, optee, u-boot and TF-a is printing out messages from USART6. But not Linux after a while.What can have caused this?My processor is: STM32MP257F.

Hi, I am designing a 25W power supply for the raspberry pi 5 for my battery powered project. The buck regulator I am using has a fixed 5V output and I want to use the STUSB4710 to offer 5V 5A to the Pi. How can I program the registers to do so via I2C? I have checked the datasheets as well as the STUSB47XX register maps but both are still quite vague on how to program.

With the recent split of STM32CubeIDE and STM32CubeMX, I'd like to propose a dark mode option be added to STM32CubeMX.In consideration of the competing priorities for STM's software development team, I have two suggestions for how this proposal could be implemented:The first suggestion is the typical route: STM's in-house software development team add the UI theming and inputs to switch between dark and light mode.The second suggestion is less typical: make STM32CubeMX open source and let the larger software community assist with adding dark mode. Perhaps the source could be placed alongside other repositories in STM's current GitHub account....The benefits of adding such an option would be as follows:Consistency with STM32CubeIDE, from which STM32CubeMX was split from (STM32CubeIDE already has a dark mode)Consistency with the vast majority of other software in the industryConsistency with what has become a common user experience across operating systems, browsers, and setups in g

Hi everyone,I'm facing a really frustrating issue where my STM32CubeIDE can no longer detect my ST-LINK, and I've narrowed the problem down specifically to stlinkserver.exe failing to launch. This problem appeared completely randomly on my PC.Here are the symptoms and what I have already ruled out:The Problem: When I try to manually execute stlinkserver.exe via PowerShell to see what's wrong, it exits instantly without printing any output, errors, or logs. Even forcing the help menu or debug mode does absolutely nothing:PowerShell PS C:\Program Files (x86)\STMicroelectronics\stlink_server> .\stlinkserver.exe PS C:\Program Files (x86)\STMicroelectronics\stlink_server> .\stlinkserver.exe -d 5 PS C:\Program Files (x86)\STMicroelectronics\stlink_server> .\stlinkserver.exe -h Running Get-Process stlinkserver confirms the process is not running in the background at all. It just dies immediately upon execution.What DOES work (Hardware & Drivers are fine):STM32CubeProgrammer

Hello everyone,   i want to build a CAN FD network with three NUCLEO-C092RC boards. So far i can transmit frames, as i can see on an oscilloscope. But the moment i connect TWO boards, the interrupt is not triggered. My code should activate user LED2 if it receives a frame with one specific id: Board 1 (0x101) triggers LED when receiving message 0x344 or 0x234 Board 2 (0x234) triggers LED when receiving message 0x344 or 0x101 Board 3 (0x344) triggers LED when receiving message 0x101 or 0x234   i use a nom. baudrate of around 500 kbit/s and data baudrate of 1 Mbit/s with a clock of 40 MHz (HSE). The Boards are connected with two short (10cm) twisted jumper cables and the jumpers for the 120 Ohm resistor are also plugged in on both baords. when i test it in external loopback mode, it works (with ident. change) Could this just be a problem with my wires (reflexion , parasi. C ,etc.)?   thanks a lot for the help

Hello everyone i am currently working on a project with a NUCLEO-C092RC Board. With this Board i want to send OBD-II Frames to my car and receive reponses with data. I also use a LCD Display via SPI. But now i have a problem. i connected CANH/L with the Board. I also connected 12V and GND from the OBD-II-Port to a buck converter, which steps the voltage down to 7 V for VIN on the Board, which should be within spec. Then i tried to send a frame, but i did not get a response, when the Board was only powered by 12V via buck converter. After that i think i broke my MCU, because then i connected my PC with the Board and switched the power source back from VIN to ST-Link with a jumper. I was able to debug my programm. but when i also disconnected CANL and CANH from the Board or switching the jumper from VIN to ST-Link (i am nor sure anymore), the red LED from STMPS2141STR came on. It only turns off, if i disconnect VDD from 3V3 Volt with pulling JP5. I also measured from what i think is

Hello. I've a problem regarding LSE On stm32l562xx mcu. Sometimes it boots, sometimes it doesn't "90 % of time it generates timeout Error" . and it takes too much time to boot up to 4 seconds. I've tried all your sdk initializations, also tried setting lse drive to all 4 modes but nothing changes. Same behaviour and same time. Below is my initialization code and attached how we connect LSE on our board. Regards   RCC_OscInitTypeDef RCC_OscInitStruct = {0};  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};  /** Configure the main internal regulator output voltage  */  if (HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE0) != HAL_OK)  {    /*Error*/  }  /** Configure LSE Drive Capability  */  HAL_PWR_EnableBkUpAccess();  __HAL_RCC_LSEDRIVE_CONFIG(RCC_LSEDRIVE_HIGH);  /** Initializes the RCC Oscillators according to the specified parameters  * in the RCC_OscInitTypeDef structure.  */  RCC_OscIn

Hello,My goal is to wakeup the end node to send a single frame then go to shutdown mode, but I'm having some hard time putting the device in shutdown modeI am calling HAL_PWREx_EnterSHUTDOWNMode(); in LoRaWAN_Process() function, after checking on a successful TxDone state.

Board / SoCBoard: NUCLEO-WB09KESoC: STM32WB09SoftwareZephyr version: v4.4.0-rc2-41-g149c8b1758a8Toolchain / build system: West + Zephyr standard build flowIssue summaryWhen building a very small Zephyr application for NUCLEO-WB09KE, simply enabling:CONFIG_BT=ycan cause intermittent boot failure.The failure happens very early in boot:no UART outputno boot bannerno application printk()main() appears to never run in failed bootsThis happens even when the application does not call any Bluetooth API.Minimal applicationmain.c#include <zephyr/kernel.h> #include <zephyr/sys/printk.h> int main(void) { while (1) { printk("M\n"); k_busy_wait(100000); } return 0; }Minimal project configurationprj.confCONFIG_BT=y CONFIG_CONSOLE=y CONFIG_UART_CONSOLE=y CONFIG_EARLY_CONSOLE=y CONFIG_PRINTK=y CONFIG_ASSERT=y CONFIG_ASSERT_VERBOSE=y CONFIG_LOG=n CONFIG_PM=nObserved behaviorWith Bluetooth disabled, the board boots and repeatedly prints:M M M ...With CONFIG_BT=y enabled, boot becomes

Hi, I am experiencing a bug in the latest version of the Extension for VS Code. As soon as I open the extension I receive this message:"Unable to contact the STM32Cube registry, verify your Internet connection..."If I run "cube bundle list-online" in the terminal I get this:cube bundle list-online Download attempt 2 out of 5 for https://developer.st.com/bundles/BundleRepositoryIndex.json ... Download attempt 3 out of 5 for https://developer.st.com/bundles/BundleRepositoryIndex.json ... Download attempt 4 out of 5 for https://developer.st.com/bundles/BundleRepositoryIndex.json ... Download attempt 5 out of 5 for https://developer.st.com/bundles/BundleRepositoryIndex.json ... Failed to list available online bundles: Failed to download bundle repository index: Failed to send request: error sending request for url (https://developer.st.com/bundles/BundleRepositoryIndex.json)But if I install the STM32Cube Core - Version 1.1.0, everything works fine:cube bundle list-online Name : P

Hi,I'm working on to get the multiple SAI to Codec to work synchronized as the connection below,1x MCLK1x BCLK1x FSYNC4x DIN4x DOUTWhere the three Clocks 1x lines (MCLK, BCLK & LRCLK) from one SAI master (actual pinout clock) & other SAI (pinout DIN & DOUT) sync clock internally (not sure possible b/w the SAI).SAI1 (clock master) -> MCLK, BCLK, FSYNC, DIN/DOUT -> codec1SAI2 (clock slave) -> (SAI1 MCLK, BCLK, FSYNC), DIN/DOUT -> codec2SAI3 (clock slave) -> (SAI1 MCLK, BCLK, FSYNC), DIN/DOUT -> codec3SAI4 (clock slave) -> (SAI1 MCLK, BCLK, FSYNC), DIN/DOUT -> codec4According to the TRM RM0436 Rev 7 55.4.4 External synchronization should be used between the SAI.does this need external pin connection between two SAI (all three clocks)? I'm facing error when arecord on SAI1 in the background and trying to start playback on SAI2, attached dts overlay filearecord -D hw:0,0 -f S16_LE -r 48000 -c 2 -d 0 /dev/null &sleep 1aplay -D hw:0,2 -f

This thread is split from this old discussion @FBL  RCC_USBPHY1REFCLKSOURCE_OTGPHY1 and RCC_USBOTGHS1CLKSOURCE_HSE_DIV2 are missing in generated code I created a simple FSBL application that is jump to the AppliThe Appli is using the same approach (SW solution) like it was implemented inside "Ux_Device_CDC_ACM" example, (it was migrated in to the Appli)Currently, during debug, I am observing the same issue like it was described before (stuck in USB_CoreReset() during checking the "USBx->GRSTCTL & USB_OTG_GRSTCTL_CSRST" )The solution, that you provided, it looks like it does not working anymore by using the latest Cube_FW and generated compilation errors (no defines for the RCC_USBPHY1REFCLKSOURCE_OTGPHY1 and RCC_USBOTGHS1CLKSOURCE_HSE_DIV2).Could you please provide a solution (it would be better to see an example) how to solve this issue base on the latest MXCube and STM32CubeIDE versions. Currently it is : STM32CubeIDE_2.1.1  STM32Cube_FW_N6_V1.3.

Hello, I would like to learn if there is an easy way in STM32CubeMX2 to start a new project with an existing ioc2 file. It seems that the only way I can do this is make a copy of the ioc2 file, do a text find and replace for the name of the project and reopen the project in MX2.In essence, I like to start a project from a working ioc2 configuration and modify it to work on a fork of the project. I don't want to recreate a complex configuration from scratch because I found the hard way that it is easy to make mistakes or to omit something. Thank you,-Gil