STM32 MCUs TouchGFX and GUI

HI,as we understand, TouchGFX does not provide support for mulitple layers, even though many targeted STM32 controllers do.We need to display a live image from the camera (at maximum possible frame rate) and overlay some gaphics on the top of it. Kind of OSD. What is the best/recommended way to achieve this task with TouchGFX? Is it feasible to do so with TouchGFX at all or the resulting performce will suffer too much?What do we do with StemWin - the hardware LTDC Layer 0 is used for the camera live image, while Layer 1 is for any graphics over the latter. Neither of two get affected by each ohter and very high frame rate is achievable without visible performance degradation.What solution TouchGFX may offer for similar tasks? Thanks.If it is matter:The display resoltion is 800x600, the camera image is a standard grayscale PAL 720x576

Hello,TouchGFX seems to have some sort of a “bug”, where in PORTRAIT orientation the text will glitch with some weird white lines, unless there is an image in the item-tree situated ABOVE text items. It doesn’t have to be any image in particular, but MUST be an image.If there isn't any image added, then every text element is glitched the moment I rotate to PORTRAIT:touchgfx::HAL::getInstance()->setDisplayOrientation(isPortrait ? touchgfx::ORIENTATION_PORTRAIT : touchgfx::ORIENTATION_LANDSCAPE);The glitched text looks as such (see the white weird lines corrupting the text):This is my item tree in TouchGFX Designer (I also tried removing the background but the white lines remained):Then, if I add any kind of image, any text area under that image in the designer stack-up, it will be displayed without glitches and any text area placed above will glitch as such (Note, the XY location in the screen does not affect this, only the stack-up arrangement!):This is the stack-up to produce such

I am using a custom PCB design with a 480x800 pixel RGB input LCD display. I am driving the display via the LTDC peripheral. When I change the default colors, the color on the screen changes accordingly, which indicates that there is no apparent hardware issue with driving the LCD.However, when I try to display a simple text on the screen using TouchGFX, the system enters the DMA2D_XferErrorCallback function due to a DMA2D error. Because of this, the text cannot be rendered on the display.Could you please explain the possible reasons for this DMA2D transfer error and what might be causing it? best regardsCelil Bayrakdar

  Hi, Currently I face problem that TouchGFX 4.26.0 use a lot of PC RAM up to 9GB RAM Project info: Resolution 480x800 Number of screen 26 Number of custom container 82 Support language: 5 Typographies: 25 With the same design for resolution 272x480 use up to 3GB RAM How can I reduce number of RAM usage? Thanks, Phat

There have been great improvements to TouchGFX  Designer and the build process.  It now cleanly allows integration into the STM32CubeIDE project structure.  The problem is that even though you can provide a project name and the output will be placed in a folder with that name, the .IOC file always has the same name as every other project made with the same device.  My workflow from the Designer, to CubeMX to CubeIDE is painless.  Generate code, then allow CubeMX to open the project and it's imported into CubeIDE.  The first project is great.  If you go back to Designer and create a different project with the same device, the process breaks down.  You'll have the same project as the last project as far as CubeIDE is concerned.  Now if you create a new workspace for each project, you can get all of your projects imported albeit you have to switch workspaces.  You can at least name them, so you know what project you're working on.  No

I have a self-contained widget (a rectangle of 360x60) which has a draggable mixin and a custom handleDragEvent.void WarningModal::handleDragEvent(const touchgfx::DragEvent& event) { if (!draggingEnabled || !animator) return; int16_t newX = animator->getX() + event.getDeltaX(); // Hard clamp: never allow leftward movement past the resting position if (newX < WARNING_MODAL_VISIBLE_X) newX = WARNING_MODAL_VISIBLE_X; animator->moveTo(newX, WARNING_MODAL_Y); }Basically it can only be dragged from left to rightI'm noticing that, if I try to move it up and down, I'm able to generate a wobbling movement up and down because, the widget tends to return to its WARNING_MODAL_Y due to the modeTo line.Is there a way to disable the drag for an axis to get a smooth movement right-left or up-down

I found I can not config ToucgGFX to APPmode.It's seems I have to config EXTEM Loader first.I tried many management,but still fail to use TouchGFX in APP.I wonder if there's other way to use GFX.By the way,I have to write the link files to fit in my HyperRam and Flash.Is there something to do with the"EXTEM Loader"and "EXTEM Manager"?Thanks a lot!

How is it with availability, are we updating what was once part of CubeMX? namely STemWin, i.e. the Segger enWIN version that was offered for free for the STM32 processor?I didn't find anything about ST, except that it's not part of newer versions of CubeMX.You can find STemWIN on Segger's website, but they're basically just trying to sell emWIN at a discount.Alternatively, where can I download the latest version of this library?Thank you for the information.

Hi,I'm using TouchGFX to make a simple screen with just one slider. This to prove my graphics work and i can use touch to move the slider.I started with a CubeMX project this time but i got stuck somewhere.I enabled DMA2D and touchGFX.I see the DMA2D IRQ's passing by and My frame buffers are swapping when i touch the screen.I see that I get calls to HAL_LTDC_LineEventCallback so I think hltdc is working as well.But i see that my images that should be drawn on my screen are not there. I see the global layout of the slider but it is not the correct image.Steps to reproduce:1) start a new TouchGFX 4.26.0 project2) disable all frameworks in config page3) Set a Box with a specific color (not black)4) Add a simple slider to the canvas5) run the simulator  In the simulator i now see the same issue I see on My device. When I re-enable the Config->FrameworkFeatures. I get a working simulator but on my embedded device the images stay wrong.I have tried everything and check

So I have a container with a single image in it. The container is used in a view and has the Mixins Draggable and MoveAnimator ON Now, I want to animate it from the current position (400,38) to 800,38 so, basically a slide animation. I have a function that should trigger the animationwarningModal.startMoveAnimation(WARNING_MODAL_HIDDEN_X, WARNING_MODAL_Y, WARNING_MODAL_ANIMATION_DURATION, touchgfx::EasingEquations::cubicEaseOut, touchgfx::EasingEquations::linearEaseNone); }wherestatic const int16_t WARNING_MODAL_HIDDEN_X = 800; static const int16_t WARNING_MODAL_Y = 38; static const uint16_t WARNING_MODAL_ANIMATION_DURATION = 12;But I don't see anything moving; why is that?

Hi All,I'm currently developing a project using an STM32N655. I'm using a 1024x600 px screen. The image format is ARGB8888. Naturally, my frame buffer takes up approximately 2.5 MB. I needed to reduce the size of the CMD list.My application doesn't have vector graphics or fonts. Can I reduce the size of the CMD list as much as I want? Will this affect performance?Also, it's not possible to double flash with internal RAM while running a screen of this size. However, would creating frames of different sizes affect the FPS? Currently, the frame rate is 32ms. Best Regards,Onur

Hello, I'm using an STM32U5G7VJTx MCU with a 480x320 display, connected to the FMC in 16-bit mode, and everything works fine using the GPU2D. I'm not using an existing GUI framework.The pixel format used by the display is RGB565 (16bpp), so for gradients, I want to use dithering to soften the banding. I found this definition in the 'nema_graphics.h' file:#define NEMA_DITHER 0x80U /**< Nema Dithering */However, it seems undocumented. How do I make use of it?Kind regerds, Jack.

Hello community,I have this problem. I have a project with the STM32U575RGTx microcontroller.It includes also FreeRTOS (Version 1.3.1) and a TouchGFX project (Version 4.26.0).With this system configuration: Timebase Source TIM17 The TouchGFX project has screens that require more or less CPU, the problem that I have is that when one or other screen is selected the execution frequency of the FreeRTOS tasks and the HAL_TIM_PeriodElapsedCallback change their execution frequency, so I can not have a valid time reference to do other things in my firmware application. Has anyone faced the same problem? Much thanks in advance!  

Hi, I'm working on the STM32H750B-DK discovery board and need to combine two key functionalities:1. Ethernet connectivity based on the LwIP stack (using the example from the `stm32-hotspot/STM32H7-LwIP-Examples` repository).2. A TouchGFX GUI that stores its assets (images, fonts) in the external QSPI flash (`MT25TL01G`) due to the limited internal flash (128KB).I have both components working **individually**: - The **standalone Ethernet example** (STM32H750_Disco_ETH) works perfectly – I can ping the board at `192.168.1.10`.- The **standalone TouchGFX application** works when the external flash is properly initialized via a bootloader, and assets are loaded from `0x90200000`.The challenge is to merge them into a single project where the application code runs from internal flash (the `APP_FLASH` region) and the Ethernet stack functions correctly alongside the TouchGFX GUI. ### **Current Memory Map (Linker Script)** I am using the following memory partition to accommodate both: `MEMORY {

Hello, I made a lot of project with Touchgfx . I started a new project with  STM32U599ZI, IAR 9.60.3 , Touchgfx 4.26.1 , CubeMx 6.17.0 , STM32CubeU5 MCU package V1.8.0.  I created project from Cube, than I double clicked touchgfx file under TOUCHGFX folder.I created a dummy project with only a red box and I clicked generate code on TouchGFX as I always do. But when I open IAR project I cannot see TouchGFX folder on IAR workspace window  and when I try to build project, IAR gives a lot of erros about not founded Touchgfx files.  Touchgfx files and folders ara exist in my project folder but not in IAR workspace window.My colluage has same proglem with STM32L4R5A mcu . I tried rebuild all, clean project, creating project from CubeMX from zero, but I could not find a solution.Can you give any solution.

Hello @INaee.1 , I am working with the STM32H743BIT6 using the LTDC peripheral to drive an RGB display. The display I am using does not have HSYNC and VSYNC signals and operates only in DE (Data Enable) mode. I have attached the display datasheet and pin connection for reference. Based on the datasheet timing specifications, I configured the LTDC parameters accordingly. Since the display does not use HSYNC and VSYNC, I configured them as constant high signals (logic 1) and set the rest of the LTDC timing parameters as specified. However, the display is not showing any image. The backlight turns on, but the screen remains black. Below are the key points of my configuration: LTDC peripheral configured according to the display timing parameters from the datasheet HSYNC and VSYNC set to constant logic high since the panel works only in DE mode Pixel clock configured as per the display requirements Data Enable (DE) signal connected and

Hello,i tried to generate for STM32f429i disco a project with graphic = touchgfx.1) i generate cubemx (for STM32f429i disco) project for SW4STM32 toolchain2) i generate a simple touchgfx project for SW4STM32 toolchainBut compilation under eclipse gives the following errors :HALSDL2.hpp:22:10: fatal error: SDL2/SDL_video.h: No such file or directoryHALSDL2.hpp:22:10: fatal error:SDL2/SDL_render.h: No such file or directorymain.cpp:30:10: fatal error: shellapi.h: No such file or directoryI can i solve these compilation errors ?thanksbest regards

I am currently using the STM32H735G-DK.​While white and red seem to display correctly, black(0x0000) appears as a dark purple when rendered. Even when displaying textures, there is a slight purple tint mixed in throughout the image.​I am writing to the framebuffer in RGB565 mode, and the LCD is reading directly from it. What could be causing this color distortion?

I have this Riverdi 7-inch display which has a STM32H757XIH6 micro controller.  And I am trying to use freertos to run a uart task when a button is tapped on the display.  I am running into an issue though with the button response.  So I created a virtual function and that works when I tap the button.  I created another freertos kernal and have a callback function names UART_Task.  I am trying to send a message via a queue to start a process when a button is tapped.  When the program runs the GUI displays, but when I tap the button it is unresponsive and does not seem to send the message.  I messed around with setting different times on the osDelay within the callback to give the GUI and other tasks time to initialize.  I also messed around with the priority of the task as well. No luck though.  Here is the Freertos code that is initialized from the main.c. The MX_FREERTOS_Init() is called in the main.c/* USER CODE BEGIN Heade

Hi guys,I'm working on custom board with STM32F411 + spiflash for a project with Touchgfx (partial buffer).At the moment I got spiflash and STM32F411 working via SP1 + DMA and that's fine.I'm using IAR 9.70 for this project and I'm facing an issue with external flash loader when I do a debugging session.When I start a debugging session, flash is programmed and the external loader programs the spiflash too.But on the end of the programming the procedure fails with:  Sun Mar 29, 2026 21:45:19: Initial reset was performedSun Mar 29, 2026 21:45:19: Loaded debugee: C:\Program Files\IAR Systems\Embedded Workbench 9.2_3\arm/config/flashloader/ST/FlashSTM32F4xxxRAM128K.outSun Mar 29, 2026 21:45:19: Target resetSun Mar 29, 2026 21:45:26: Unloaded macro file: C:\Program Files\IAR Systems\Embedded Workbench 9.2_3\arm/config/flashloader/ST/FlashSTM32F4xxx.macSun Mar 29, 2026 21:45:26: Loaded macro file: D:\ARM\STM32F411\AlphaTui\CubeMx\AlphaTui\EWARM/icf/ExtSPIFLd.macSun Mar 29, 2026 21:

I have an stm32h7s78-dk and I created a GUI with TouchGFX.  I am trying to transmit some data via UART when a button is pressed.  I have the virtual function triggering in my MainDisplay and I was trying to use FreeRTOS and Queues to communicate from the virtual function from the button press to the uart task that I created via STMCubeMX.  For some reason though, the screen stays black when I try to use an if(xQueueReceive(queueHandle, &message, 0) == pdPASS) { printf("Message received"); }in my uart task. If I comment out this code then everything works fine and the GUI is visible.  I'm not sure what I'm doing wrong.  Here is my main.c/* USER CODE BEGIN Header */ /** ****************************************************************************** * @file : main.c * @brief : Main program body ****************************************************************************** * @attention * * Copyright (c) 2023 STMicroelectronics. * All rights rese

Hello I have a STM32f469-discovery. I have trouble loading code/programming. I have successfully programmed the board via the Flowcode software. Also I can use the Hex or Bin generated file from Flowcode, import it in the STlink utility and load it on the board. That works. What I can't do is to open a demo or example for the touchGfx designer and program the board. I click on the "program and run target" but ends up in error"ST-LINK error (DEV_CONNECT_ERR)c:/TouchGFXProjects/MyApplication_7/gcc/include/flash_sections_int_ext.mk:2: recipe for target '_extflash_' failedmake[1]: *** [_extflash_] Error 1../gcc/Makefile:53: recipe for target 'flash' failedmake: *** [flash] Error 2FailedIn the touchGfx there is no indication that the board is connected. I get indication only on the STlinkIf I select the "Generate code" it successfully does it but later on I dont know where to load that code in order to use it to program my board via another software. Is there a specific sequence f

Hi, I am trying to configure the X-NUCLEO-GFX02Z1 display expansion board with the NUCLEO-F767ZI board. The LCD controller used is ST7789, and the interface is configured via FMC. During BSP initialization (BSP_LCD_Init), I am encountering an error: Return status: BSP_ERROR_COMPONENT_FAILURE The LCD ID read is not as expected (expected value: 0x858552U as per the BSP driver) However, if I bypass this failure and proceed: I am able to set the orientation using BSP_LCD_SetOrientation I can retrieve the orientation using BSP_LCD_GetOrientation successfully When attempting to draw on the display using:BSP_LCD_FillRGBRect(0, 0, (uint8_t*)buffer, 0, 0, 100, 100); there is no visible output on the screen. Could you please help identify: Possible reasons for incorrect LCD ID reading? A minimal working example to display a solid color on the screen using this setup? Any guidance on debugging steps or known issues with this board combination would be greatly appreciated. I am already

Dear community, I’m sharing an application that has been highly requested recently: a demo running TouchGFX on the STM32N6570-DK with a camera module.Please note that this demo is NOT yet finalized. We plan to significantly enhance it over the coming weeks, and once it is ready, it will be directly available in TouchGFX Designer as a board-specific demo (under the Demo tab).In the meantime, since there has been strong demand, here is an early draft that you can already use and draw inspiration from.Another note, we’ll provide only limited support for any questions about this draft, as we are aware of the application’s limitations and are working on a much better version. Again, this demo is not final and does not reflect the quality of an official demo.The project works with TouchGFX 4.25.0 and with STM32CubeIDE. We advise NOT to regenerate code from STM32CubeMX (because there is a limitation here). You can use the flashing scripts provided in the project to flash your board.  

TouchGFX version 4.25.0 CubeMX version 6.17.4*  STMCubeIDE version 2.0.0*edited versionI created a development environment starting with TouchGFX and used Generate Under Root in CubeMX.  This did a great job of setting up the directory structure without links so that it is easier to navigate in the STM32CubeIDE application.Part of this process automagically moves the middleware and driver directories from the STM32CubeIDE directory to the root directory.When the .project file is created by the TouchGFX code generation it handles the movement of all these files and include directories like a champ, except the Properties=>C/C++ Build=>Settings=>MCU/MPU G++ Linker=>Libraries=>Library search path for the libtouchgfx-float-abi-hard.a library.It sets the path to "${workspace_loc:/STMCubeIDE/Middlewares/ST/touchgfx/lib/core/cortex_m7/gcc}" instead of "${workspace_loc:/${ProjName}/Middlewares/ST/touchgfx/lib/core/cortex_m7/gcc}"It's a quick fix to edit it to