STM32CubeMonitor (MCUs)

Hello, I followed the tutorial with just one variable (extracted from an elf) there was no problem the variable showed in the chart. But when I added another variable to the code and got a new elf. I went to the variable node to add the new variable but there's none (the first variable also gone). I tried with other elf files from other projects but it doesn't work either. Thank you in advance! (I'm using the CubeMonitor in Window10)

Good day. So I am busy with my final year project, where the goal is to control the speed of a DC motor by reading the armature voltage and current, and then estimating the speed of the motor. I am using the STMCubeMonitor to provide a reference speed, and then the estimated speed is plotted vs the reference speed in the Cube Monitor. I have 1 USB port available on my laptop, therefore I tried using a USB Hub to connect my external mouse and the STM32. When I have this configuration, as soon as a reference speed is entered, the motor does as expected and increases the PWM to reach the desired speed by varyng the voltage, but then the STM disconnects and the monitor stops. I then tried unplugging my mouse, and pluging the STM32 straight into the laptop's USB port. The STM then does not disconnect anymore, but as soon as I set a reference speed, my trackpad stops working and jumps around like crazy and therefore can't enter another reference speed. I have read some issues people are havi

Hello again, I know i posted some time ago but my question is not seen anymore (link to original https://community.st.com/s/question/0D53W00000wWDX2SAO/cubemonitor-still-not-seeing-boolean-values)I was suggested to to include "stdbool.h" but, as I'm working with a C++ project, G++ says that bool is supported and what I get in "stdbool.h" is the following (italic is greyed out code):#ifndef __cplusplus#define bool   _Bool#define true   1#define false   0#else /* __cplusplus *//* Supporting _Bool in C++ is a GCC extension. */#define _Bool   bool#if __cplusplus < 201103L/* Defining these macros in C++98 is a GCC extension. */#define bool   bool#define false   false#define true   true#endif#endif /* __cplusplus */I could manually modify the file to use "C" bool but, is there another way?Thank you!

How to make a chart with a similar functionThe x-axis range is fixed, zooming, etc., the historical waveform is not saved, only the current 10s waveform is displayed

..

..

can stm32cubeMonitor recognize IAR IJet probe?I saw in one of your pages that it should but I tried it with 2 different computers and even though it recognized st-link, it didn't recognize the IJet probe.

I am using the STM32CubeIDE on Fedora linux and I would like to try the STM32CubeMonitor. However only .deb package is available. Is there (or is planned) the release of RPM package?I tried to convert the .deb package using the "alien" utility, unfortunately without success.

Hello,I'm new to STM32CubeMonitor and I need some help. I made a project that consists of sending an unkown length string (DMA) to a nucleo board and then receive the same message on my terminal.I've been using realterm and it works fine, but i would like to know how to send strings using STM32CubeMonitor software.I want to type a message on a 'text input' node, press a button and then send the string to the board.Thank you,Iñigo

Following our STM32CubeMonitor webinar on April 13th, 2021, here are the list of resources and list of Q&A posted as separated answers.Webinar website: https://www.st.com/content/st_com/en/about/events/events.html/stm32-application-monitoring-with-stm32cubemonitor-webinar.htmlWebinar on-demand (watch recording): https://www.st.com/content/st_com/en/premium-content/premium-content-remote-stm32-application-monitoring-with-stm32cubemonitor.html STM32CubeMonitor page: https://www.st.com/en/development-tools/stm32cubemonitor.htmlAttached STM32 demo project and technical slides presented during the demonstration.Below are the questions and their respective answers

Just powered up the  X-NUCLEO-LPM01A with a L432KC mounted in the Nano socket but without having software to cycle thru test modes I have a flat line. In other words, blinky don't cut it for power monitoring.

I plan to show the dashboard via browser to other people, I am afraid they might mess up my flows. Is it possible to add security functionality?I was trying to comment out as per instructions here:https://nodered.org/docs/user-guide/runtime/securing-node-red#editor--admin-api-securitybut the flows will not show after I enabledadminAuth

hello everyone!There are some problems in using snapshot mode.When I switch to snapshot mode, I often can't collect data, as shown in the picture. After a few reboots, the software can work normally. What are the possible reasons?Best regards

..

I have Dell laptop with 4K display (XPS 15).A solution to handle this - to reduce the display resolution to 640x860 by the OS. please use updated JRE which can handle such displays.

I instrumented the code with the supplied code, and it works fine in STM Studio, but when used in CubeMonitor, after started, the dashbord just displays 'Acquisition started, waiting for value'. I've checked the data flow from STLink and found that only 'x' value present in the data payload, but without 'y' value.Is there a way to trigger the data sample manually? Or supporting trigger is mandatory in snapshot mode?

Trying to monitor a 'C' variable of type bool results in the errornot connected ! bad parameter (7)and the probe connection drops. It then comes back all on its own!!Changing the variable to any other type and the monitor runs fine.

Helo, Dear ST!I very happy for use Yours many devices. They are very cool! You are very cool too!So, I was download Your STM32Monitor on my PC. But after install this software on the my Windows 7 I seen unreal picture:Installator of STM32Monitor putted its Icon on the my descktop and after I double clicked it was destroyed and removed all installation files and directories. After, I tryed next two Installs of this software - nothing. All is bad.Please, tell me what I need for repair this problem.With Good wishes,Arthur Tim

I want to in corporate conditional data logging in Cube Monitor Flow, since i intend to monitor the behaviour over many hours.My requirement is to log all the 4 fields:ms_enDeviceOrientationms_stStAccelDataXms_stStAccelDataYms_stStAccelDataZonly if ms_enDeviceOrientation changes from value of 1 to value of 2.I tried to tie this to the trigger threshold in data acquisition but this option was disabled.Could not find any examples to do this any other way.Looking forward to clear and specific description or example.Thanks in advance.

..

After rebuilding an ELF file, going into the Edit Variables node indicates that those variables alphabetically near the top are retained but those further down the list have been dropped requiring them to be re-selected. Is this a memory overflow and is there a way of allocating more memory so this doesn't keep happening?Thanks.

Hi Everyone!​I just started my first STM32F4 project and I was wondering if there is an IDE that can show the content of a range of memory in form of a data plot.​I ​tried to find someting on the web but had no luck so far.​This means for debug I am currently sending data in 8bit blocks via the serial port to the PC. Stitch it back together and plot it in Octave/Matlab.​Is there an easier way, ideally in the IDE? I am using AC6 at the moment.​​

I'm having trouble monitoring signals of my project running on an STM32G431 through STLINK-V3SET and B-STLINK-ISOL. The system works well with the STLINK-V3SET alone.Regarding link settings on the STLINK-V3SET and B-STLINK-ISOL: I've removed JP1 on the STLINK-V3SET base card and installed JP1 and JP2 on the B-STLINK-ISOL.When the B-STLINK-ISOL is in place, I can deploy the configuration and, display the "Dashboard" but when I press "START ACQUISITION" I see this message in the Debug window: PMnode: myProbe_Outmsg : string[33] "JTAG/SWD no device connected (f7)"Just wondering if anyone can help me understand what I'm doing wrong?Thanks

i increases by 1.  The delay is 1.stm cubemonitor variables node I received the data as an Excel file.x is the time, and y is the value of i.The time interval of the data is 1 ms(=0.001s).Can you make the time interval shorter?If you can shorten the time interval, please tell me how to do it in detail. please.thank you. 

Hi All,I want to plot the current state of the microcontroller at the same time. From what I understood it is possible using stm32CubeMonitor and STLINK-V3PWR. I have seen a similar dashboard in AN5999  but I couldn't find a way to create such a dashboard that displays the current using STLINK-V3PWR.How can I create a dashboard such as below?