Automotive and Transportation

I want to ask about AEK-MCU-SPC5LNK. Is the support applied for processors SPC56? I have AEK-MCU-SPC5LNK and SPC56EL70L5DISP board and I can't find cfg files for SPC56EL processor.Lukasz

Hello, I am currently developing with SPC5Studio 6.0.0.In my project, I need the HighTec Pro option, so I downloaded the license and tool chain files from http://register.hightec-rt.com/st/spc5x.I placed the license file in both:- C:\SPC5Studio-6.0\licenses- C:\HIGHTEC\licensesHowever, it still says that no valid license can be found.How can I resolve this issue?Best regards.

HI,I am using x-stm32mp-gnss2 evaluation board and interfaced with the host PC through UART to USB converter for utilizing the TaseoSuitePro7_3_3_1 Software.I need following measurements for my college project:1) Time of the measurement2) Pseudo-range measurements 3) Carrier phase4) Ephemeris5) Doppler frequencyI am not able to configure the liv4F for above output parameters. Request to suggest solution for obtaining these parameters.

Hi all,I have been using the TESET-VIC3  to test IMU sensor, I enable SENMSG from message list 0 ($PSTMSETPAR,1228,0x7********) I found that latency is so High when I receive $PSTMSENMSG,30/31 So I chose to disable all GNSS-related msg and keep only the sensor msg from message list 2 (for low lattency) :$PSTMSETPAR, 1228, 0x0$PSTMSETPAR, 1201, 0x0$PSTMSETPAR, 1230, 0x10000000$PSTMSAVEPAR$PSTMSRR Once I did that, the module is no more responding to any cmds, not replying to $PSTGETPAR nor $PSTSRR, not even factory restore... UART TX Pin of the TESEO is always set on 1 ! I lost control of the module. Anyone could help with that and how to make it respond back ?Thank you in advance 

Hi everyone,I want to know if the microcontroller SPC560P-DISP: Discovery+ evaluation board allows me to work with CANFD. I want also to know if there is any tutorials to learn how to use it for this purpose.

Hi,I bought a Teseo-VIC3DA Evaluation Kit and when I went through the associated documents, they mentioned the concepts of "Teseo-DRAW and Teseo-DRUM". In my application, we do not have access to the vehicle's wheelticks/direction information so I guess I need to use DRUM. But I could not find any information about how to configure the evaluation kit to work in DRUM. Are DRAW and DRUM two different firmware or two different modes?Another question is about the DR calibration. I first updated the firmware to BINIMG_4.6.18.11_VIC3DA_ARM and did not change any configuration. Then I installed the kit to a vehicle and after half an hour driving, I could see $PSTMDR2 showed "system ready" and $GPGGA showed the DR was working with location readings (strangely $PSTMDRCAL did not show up anymore but that may be a separate topic). Then I pulled the kit off from the vehicle and put it in my office, and found that $PSTMDR2 still showed "system ready" and $GPGGA still showed the DR wa

Could someone clarify the interrupt priority order for SPC58 MCU family? Is 0 the highest priority or 63 is the highest priority?Best regards

I’m working on an SPC560B MCU project that includes both a bootloader and an application. The application runs without any issues. However, when running in bootloader mode, the MCU experiences repeated resets.Upon checking the RGM_FES (Reset Generation Module – Fault Event Status) register, I can see that both F_CHKSTOP and F_SOFT flags are set.I’m trying to determine what could be causing this reset behavior. Some specific questions:What are the typical causes of F_CHKSTOP and F_SOFT resets?Are there specific registers or debugging steps I should look into to pinpoint the root cause?Thanks in advance!

Hi,   I'm learning to use it SPC58EC serial chip and have a question,when it was previously used on Arm chips, there were some exception handling interrupt functions,like Hard_Fault_Handle,this ensures easy traceability when problems arise, my question is how to configure similar exception interrupt functions on this chip（SPC58EC），I would appreciate it if you could provide some examples，thank you very much

Hi there,I am working with a company developing an automotive control module that connects to several systems that must be able to wake up the module from STOP mode or Standby modeOne of the modules signals the wakeup request over the CAN bus, and I was wondering if it was possible to integrate this functionality into the firmware of the SPC582B60 microcontroller.I had a read through both the WKPU and MCAN sections of the datasheet, and could not find any conclusive information about how I might go about this or whether this functionality is supported in this microcontroller.Any suggestions for implementation of this functionality, or alternative microcontrollers that may provide this functionality will be greatly appreciated.Kind regards, Rusira

Hello community,I am using AEK-AUD-C1D9031 board and I want to play 2 audio files one after other. What should I change in the code?

Hi I am using UDE STK 2021 debugger software and for that I am using PLS-UDESTK debugger(HW), for SPC58NN84E7 microcontroller  I could see the PLS-UDESTK is mentioned as NRND(Not recommended for new design) So I am planning to use AEK-MCU-SPC5LNKU with same above mentioned SW debugger. Can you any confirm me that AEK-MCU-SPC5LNK supports UDE STK 2021 SW debugger Thanks in Advance   

Hello,I am trying to set up the 14 cell GUI using the C4MLIT1, ISOSPI1, and BMS63EN boards. At this point in time, I am only interested in the logging functionality and just want to use the demo as it comes.I have the hardware set up in centralized configuration, with just a single BMS63EN connected to 14 cells via the BMSHOLD cell holder (~56 V total). When I start the GUI, the serial port connects, but no data appears.Could someone advise on whether I have understood the broad steps correctly, starting from having AutoDevKitStudio installed and GUI project imported?Move GUI .exe to desktop.Connect ISOSPI1 to MCU as per the board view schematic, shown by clicking "SPC58EC 4M board view". Also connecting vcc and vio to 5V.Connect BMS63EN to ISO board via USB connector.Connect BMSHOLD cell holder (with cells) to BMS63ENConnect MCU to PC and generate + compileStart GUII just want to confirm whether I have the simple stuff right first before moving on. I'm slightly concerned I may have bu

Hello,I have been trying to connect to the AEK-MOT-TK200G1 using a SPC5-UDESTK.I tried UDE starter kit 5.02.04, and UDE starter kit 2021.05. I'm getting the following error: (Message from component 'PpcJtagTargIntf' :Can't connect target !)I have checked all drivers and versions but I still get the same error. Here is my device manager: I ran out of ideas of what to try next. Has anyone got this setup working?  Thanks,Alex   

I'm trying to debug to SPC582B-DIS board and I'm trying to 2 combination.But I didn't succeed debugging.First, I'm using SPC582-DIS Board rev 1.1 and AutoDevKit Studio version 2.4.0.I installed openodc drivers according to the doc named 'How to use OpenOCD and SPC5-UDESTK in SPC5Studio'.These are located 'AutoDevKitStudio-2.4.0\openocd\docs' and  'AutoDevKitStudio-2.4.0\openocd\drivers'. Second, I'm using SPC582-DIS Board rev 1.1 and AutoDevKit Studio version 2.4.0 and UDE STK 5.2.I installed PLS UDE Driver and UDE STK 5.2 according to 'SPC5-UDESTK Getting Started' manual.I used AutoDevKit to make .elf and wsx. And I Opend .wsx by UDE STK.  I swapped USB Driver in two combination cases. 

Hello, I am trying to debug an example code on a recently bought AEK-MCU-C4MLIT1 Evaluation Board via AEKSMCU-SPC5LNK using OpenOCD. I am fairly new to Embedded Systems and Eclipse Environment so I have just been following instructions.  And things don't seem as straightforward as STM32CubeIDE.... When I am trying to debug the board, I receive the following error on the console.  Open On-Chip Debugger 0.12.0+dev-00318-g0e98d766e (2023-05-17-15:52)Licensed under GNU GPL v2For bug reports, readhttp://openocd.org/doc/doxygen/bugs.htmlStarted by GNU MCU EclipseInfo : Listening on port 6666 for tcl connectionsInfo : Listening on port 4444 for telnet connectionsError: Debug Adapter has to be specified, see "adapter driver" command   Also, I am not sure whether the Board AEK-MCU-C4MLIT1 is alright or not. Should I expect some LEDs to be Switched ON on the board when I connect the usb or the 12V supply? I have attached the screenshots of my Debug Configuration.&nb

Hello,I am currently exploring the SPC5Studio IDE for developing applications on SPC5 family microcontrollers and have a couple of questions regarding its features:1) Licensing Requirement:Does SPC5Studio IDE require a licensed version for full functionality, or is there a free version available for all users?If there is a free version, are there any restrictions or limitations in its features compared to the licensed version?2) Programming the MCU Using a Debugger:How can I program the SPC5 family microcontroller using a debugger in SPC5Studio?What are the supported debuggers and programming interfaces (e.g., JTAG, SWD) for this IDE?Is there a step-by-step guide available to configure and use the debugger for programming and debugging SPC5 MCUs in SPC5Studio?3) HAL Layer Support:Does SPC5Studio provide support for the Hardware Abstraction Layer (HAL) for SPC5 family microcontrollers?I would appreciate any insights or official documentation regarding these topics.Thank you in advance f

For your information , StellarStudio 7.1.0-JOURNEY version is officially pushed (for SR5x). (Windows , Macos, Linux) based on eclipse 202409 and the version CDT 202409 with standalone tools (Java 21) https://www.st.com/en/development-tools/stellarstudio.html StellarStudio (Pinmap (SR5x), Clocktree (SR5E1), NoC Configurator, Power conso) (Windows, Linux, MacOs) with StellarESDK-1.8.0 (SR5X) and TOOLS-1.4.0 with Git Bash Eclipse Integration / Update site system. with eclipse project creation wizard based with multiple sdks support (Integration of  ESDK 1.8.0) with new pinmap wizard with board selection mechanism with Power consumption wizard. with CDT / embedded cdt / Openocd debug Integration with Migration tool from Old Pinmap to New Pinmap model Compliant with TRACE32 Lauterbach / ISYSTEM / Segger J-Link / Openocd. What's new in this release ? -SR5E1:                    &nbs

HelloI need to use full featured Teseo-Suite.Sending letters to st-teseo-suite-support@st.com remain unanswered.How could I obtain a full version of Teseo-Suite?Thanks

Hey Community!I am trying to build a BMS for a 333V Battery using AEK-MCU-C4MLIT1 as the Master MCU, AEK-COM-ISOSPI1 as the translator and multiple AEK-POW-BMS63EN boards in a daisy chain.Although there are various examples provided in the SPC5Studio that one can use to get started with the BMS System. However, I am still finding it difficult to use the API functions effectively. I feel that although there are a lot of functions available in the API, their definitions are still absent in the documentation. Is there any other documentation which one can read to understand the data structures and different functions present in the API for the AEK-POW-BMS63EN?Thanks,Vipul

Hi the Teseo VIC3D datasheet doesn't seem to have very detailed electrical specs and neither does the UM2832 hardware manual. I assume the gpio are push pull referenced to VCC. I'm looking for VIH, VIL, VOH, VOL, any power on or sequencing requirement between VCC and VBAT. Where can I find stuff like that ? 

Hello everyone,  I am currently working on SPC5 microcontrollers and a bit new with SPC5 studio can anyone guide me how to make an application for running SPI , I am clear with the basic of SPI communication.      

Hello All,I am doing project that Controls Watchdog Adc to trigger interrupt for higher Threshold value and lower Threshold, When Threshold Reaches Maximum and Minimum ISR happens, in ISR function it blink onboard led.Using Onboard POT for watchdog adc Tuning High Threshold and Low thresholdOnboard LED Blink for ISR -Threshold high and low Interrupt For this I am using SPC560d Dev board . We have Example Application Library for ADC it has all the function to work properly, but i want to do on my own by Register based using Xpc560d.h header fine, for that i cleared main.c file in Example ADC Application Library. Now I struct at Clock configuration for Watchdog Adc, Below code when debugging, program hangs on Clock configuration like api configI have selected Sysclk-->FIRC  in RLA clock treeSysclk= 48mhzRun mode : DRUN RUN0 mode pheripheral clock 24mhz  PINOUT:PB[10]=ADC_1 Extended channel 6PC[2]=GPIO output LED PC[3]= GPIO output LED &nbsp

I would like to know, in the Stellar SR6G7, whether the BCS code will execute first or if we can configure a custom Boot Manager to execute first. Since I need to run secure boot with HSM, I want to configure the Boot Manager for PLL clock initialization and run the HSM first. Then, the BCS will execute the handshake with the HSM. Is this possible in the SR6G7, or will the BCS handle initialization and perform the handshake with the HSM during startup before any custom Boot manager?

Hello everyone,I have been flashing the code written in AutDevKit Studio 2.4.0 using UDE STK 2021 for the AEK-AUD-C1D9031, which uses the SPC582B60E1 MCU. I want to start debugging the code line by line using breakpoints.Currently, I have the option to add breakpoints in AutDevKit Studio, but it is of no use since I am flashing the code with UDE STK 2021.Could someone guide me on how to add breakpoints in UDE STK 2021? Also, how can I add variables to the watch window?I referred to the manual I attached but couldn’t figure out the exact steps to add breakpoints or watch variables in the program shown in UDE STK 2021.