Product forums

Homes often require electrical repairs, upgrades, or new installations to maintain safe and functional living spaces. ENV Electric provides affordable residential electrical services in Durham for homeowners who need reliable electrical work. Their electricians inspect existing systems, repair wiring issues, and complete installations that meet safety standards. Affordable residential electrical services in Durham help homeowners manage electrical improvements without unnecessary complications. Many residents choose affordable residential electrical services in Durham because experienced electricians deliver practical solutions for everyday electrical needs. 

Hello,I am working with an STM32F103RB Nucleo board. I am able to successfully connect and program the device using ST-LINK, but I am facing an issue during debugging.The code is downloaded successfully and verified, but when the debugger tries to run (after the 'cont' command), it fails with the following error:Error in executing 'cont' commandTarget is not respondingFailed to read all registers from targetSetup details:- Board: NUCLEO-F103RB- ST-LINK Firmware: V2J47M34- STM32CubeProgrammer: v2.20.0- Debug Interface: SWD- Connection Mode: Under Reset- Reset Mode: Hardware reset- SWD Frequency: 125 kHzObservations:- Programming completes successfully- Verification is successful- Issue occurs only when starting execution/debuggingThings I would like help with:1. What could cause the target to stop responding immediately after programming?2. Could this be related to clock configuration or incorrect startup code?3. Are there specific debug settings (reset mode, SWD frequency, etc.) I shou

Hello all, I need to use some FFT functions. I have installed the CMSIS-DSP 1.16.2 and CMSIS 6.3 core as it was required from  CMSIS-DSP. Surprisingly, CubeMX did only a part of its job, namely it did not copy source files and did not add proper include paths to the project so I have to do it myself. But after this there is still a bunch of unresolved references, namely arm_cfft_sR_f32_lenxxx and twiddleCoef_rfft_xxx. I have looked all sources in the CubeMX H7 pack version 1.13.0 I use through but could not find these sources. With best regards,Dmitry 

Using https://stm32ai-cs.st.com , starting with my .tflite model. My goal is to incorporate the new model into the STM32N6-GettingStarted-ObjectDetection example.  I am having some issues with versions.The ST Edge AI Developer Cloud produces a version of the model which differs from the version used by the support files in the example code. Case in Point - the function LL_ATON_LIB_Concat: the example has 6 parameters and code generated from the ST Edge AI requires 7 parameters.  Dr Google, suggests there is another option when I "Download C Code" from the AI Developer Cloud that I should also have an option to change the Target Output to "STM32CubeIDE Project", "System Performance Project", or "C-Project".I don't see that option. can you help.

Hello Peter ,  Need your expert reply  As we see , the confusion on N AND no N HAS MADE many of us wonder , if these can be used as  interchangeable parts . Since Data Sheet does not explain , much on them ,But a search explains a compact Solution in Io's for a design flexibility .  As both have same Packages and Pin  Count .  We are in need for DESIGN - STM32G0B1CBT3N , but seems to be difficult  to procure  . Is this Manufactured or is it rare . We only See STM32G0B1CBT6N    Regards Nitin

 I am using STM32N6570-DK board . I am trying to build edge AI code in application mode with the help of generated STM32 cube AI studio generate project for IDE. I am following this article https://community.st.com/t5/stm32-mcus/how-to-build-an-ai-application-from-scratch-on-the-stm32n6570-dk/ta-p/825591 . @Julian E. This article includes AI using X-Cube AI , I just wanted to ask if I am using the project/ AI files generated by STM32 Cube AI studio, Will the configuration of external memory manager and addresses we are using in XSPI2 , RAMCFG , RCC settings all will remain exactly same ? I am asking this as I am getting some memory issues while debugging the application code.Also my code includes ADC+USART also, will this add to additional memory changes?

Hi,After reading HSO current and voltage sampling in three-shunt topology, I beleve it is possible to run two BLDC moters using the ST-G473 microprocessor using 2 ADC's per motor. However, there does not seem to be support for that in the MC Workbanch. Will this be available in the future?Regards, Kevin

Hi Does anyone know how to stabilize the gyroscope and accelerometer signals. I am getting signals back but I am trying to move a radio button on a bullseye and can't seem to smooth out the signal. I am using I2C communications.  

hello ST Community, I need your support. So far, I've been able to flash my bootloader software into the unprotected memory area 0x08000000 when Boot0 = 0 for the NUCLEO-H755ZI-Q series, both with the STM32CubeProgrammer and with my bootloader software via UART. However, I'd like to flash the same bootloader software into the memory area 0x1ff00000 when Boot0 = 1. I know it's protected. Is it possible to change the security level or flash it to another memory to run my software when Boot0 = 1? Thank you for your support.

Red light flashing. App showing 0% charged after 15 minutes

@Ulysses HERNIOSUS Dear Ulysses,Sorry to bother you again. code : err = rfalTransceiveBlockingTxRx(tx_buf, sizeof(tx_buf), rx_buf, sizeof(rx_buf), &actlen, RFAL_TXRX_FLAGS_CRC_TX_MANUAL|RFAL_TXRX_FLAGS_PAR_TX_NONE|RFAL_TXRX_FLAGS_CRC_RX_KEEP|RFAL_TXRX_FLAGS_PAR_RX_REMV|RFAL_TXRX_FLAGS_CRC_RX_MANUAL, 71680U); I want to send 4 bytes data and 4 bits parity, how do i combine those 36 bits data to 5 bytes data and send with function rfalTransceiveBlockingTxRx. for example:data_enc: 03, de, 59, bdparity_enc: 00, 00, 00, 00tx_buf: 03, bc, 65, e9, 05is it correct? can rfalTransceiveBlockingTxRx send 4bit data? Thanks

Hello, Iam working o STM32H573I-DK Board when am trying to access board am getting trustzone issue.I tried with Debug Authentication also but am unable to access board.Find the attached description. 

I am using STEVAL-MKI109D + STEVAL-MKI238A. I have evaluated motion-stationary FSM example as it seemed closest to what we want to use for our application. It seems to work fine, however it is too sensitive and needs some upgrades.What I want to achieve:Setup timer (TI3) to some value such such as 5 seconds. During this 5 second period, I want to detect specific number of events above certain threshold (GNTH1). If specific number of events were detected during 5 second period, generate an interrupt and repeat over and over again. If specific number of events were not detected during that 5 seconds period, just reset the counter and repeat.My cofiguration:It sounds like a simple requirement but I cannot achieve it using FSM.I tried to achieve this using 2 FSM's: FSM1:FSM1 is responsible for incrementing long counter everytime the GNTH1 is reached. FSM2:FSM2 is responsible for resetting long counter. I don't really understand why the MEMS Studio forces me to put STOP command at

  I have tried using STM32CubeMX 6.17.0 to generate an STM32F429 DISC1 project.The generated project opened in STM32CubeIDE could not be compiled unless I add <root folder> in Project -> Properties -> C/C++ General -> Path and Symbols, the source location tab.I don't know how this happen. It's disturbing to modify project settings each time after modifying the CubeMX and generating the project.It's probably that should happened after I add some source folders to the projects. 

Only 2 of 4 QSPI data lines active during pixel write, despite DMODE=3 confirmed in CCR 이미지 4장을 모두 참조하여 ST Community 문의 글을 작성합니다.EnvironmentMCU: STM32U5G9ZJ (Cortex-M33, TrustZone enabled)IDE: STM32CubeIDEHAL version: STM32U5xx HAL Driver (included in project)Interface: HSPI1 → QSPI LCD (ICNA3306-compatible controller) Hardware ConfigurationGPIO settings are shown in [XSPI_2.png]. All six HSPI1 pins are configured as Alternate Function Push-Pull with GPIO_SPEED_FREQ_VERY_HIGH and GPIO_AF8_HSPI1:Pin Signal Speed PI3HSPI1_CLKVery HighPH9HSPI1_NCSVery HighPH10HSPI1_IO0Very HighPH11HSPI1_IO1Very HighPH12HSPI1_IO2Very HighPH13HSPI1_IO3Very HighClock configuration is shown in [XSPI_3.png]: HSPI1 kernel clock source is set to SYSCLK (160 MHz). PLL1: HSE(16MHz) × PLLN(10) / PLLR(1) = 160 MHz.CubeMX parameter settings are shown in [XSPI_1.png]:Fifo Threshold: 4 bytesMemory Type: MicronClock Prescaler: 1 (→ FCLK = 80 MHz)Clock Mode: Low (Mode 0)Sample Shifting: Half Cycle Problem

Is it possible to connect 8 PDM microphones to the STM32N6 via MDF?

Hello,I am facing an issue with the STM32C5 HAL SPI driver related to CRC error detection.In my setup, CRC is enabled for SPI. When a CRC error occurs, I can observe that the CRCERR flag is set before the transfer is closed. However, the CRC error is never reported via the HAL error callback.Looking into the HAL implementation, I noticed the following behavior:SPI_CloseTransfer() calls LL_SPI_Disable()After disabling SPI, SPI_CloseTransfer() checks LL_SPI_IsActiveFlag_CRCERR()When this check is performed after LL_SPI_Disable(), the CRC error is no longer detectedIf I move the LL_SPI_IsActiveFlag_CRCERR() check before LL_SPI_Disable(), the CRC error is detected correctlyAdditionally, in my case SPI_CloseTransfer() is called from HAL_SPI_IRQHandler(), but:the return value of SPI_CloseTransfer() is not evaluatedonly the Tx/Rx complete callback is invokedmy error callback is never called, even though a CRC error has occurredFrom my understanding:LL_SPI_Disable() itself does not clear the C

This is an improvement request post.STM32 HAL on every family has tons of following code constructs:tickstart = HAL_GetTick(); while (!condition) { if ((HAL_GetTick() - tickstart) > TIMEOUT_VALUE) { return HAL_TIMEOUT; } }When using HAL with (Free)RTOS or interrupt based scheduler, then these while loops delay same priority tasks (until time-slicing kicks in), block everything that has lower preemption priority, waste energy (crucial for battery powered devices) and decrease responsiveness.There are multiple ways to improve it. One of the simplest is to supplement non-critical* loops with optional user-definable yield macros.__weak void HAL_Yield(void) { } tickstart = HAL_GetTick(); while (!condition) { if ((HAL_GetTick() - tickstart) > TIMEOUT_VALUE) { return HAL_TIMEOUT; } HAL_Yield(); }Now user can implement something like this when using CMSIS OS v2 API:#include "cmsis_os2.h" void HAL_Yield(void) { /* Kernel running and call not from ISR? */ if ((osKernelG

Is Cosmic license delivery service still working ?I submit the request, but I didn't get any answer! 

Hello, I have a STM32 NUCLEO-N657X0-Q development board. I wanted to interface with 8 digital PDM MEMs microphones.  In section 68.2 of the STM32N6 reference manual, it states that the N6 supports a "PDM interface, supporting up to 4 microphone pairs". Also in section 2.2.3 of AN5027, it states that if 8 microphone want to be used, the recommended data IO lines are SAI_D1, SAI_D2, SAI_D3, and SAI_D4. Using CubeMX, I see no option for microphone pair 7-8. In addition to this, SAI_D4 doesn't exist when I search for the pin.  So how do I interface (if possible), the last microphone pair?  Thanks, Christopher

   SPC5 Flash ProgrammerSPC5 Flash Programmer 2.8.1 Fail to connect to SPC564 via UART!, when I did some search, I found that SPC5 Flash Programmer v2.7.9 working fine, so please if you can help me to how get this version SPC5 Flash Programmer v2.7.9? 

Hi everyone, I am currently developing an image capture project using the STM32N657 (Cortex-M55) and have encountered an extremely bizarre DMA2D write issue (a silent failure). Goal: Use DMA2D (M2M_PFC) to convert an RGB565 buffer to RGB888 and write it to CPUAXI_RAM1 (0x34080000). [Problem Description] I wrote a "minimal isolation test" to bypass all camera/GPDMA variables. I forced the CPU to fill the source buffer with pure white (0xFFFFFFFF), and then manually triggered the DMA2D to transfer it to the destination buffer. The Result: The DMA2D finishes successfully. The DMA2D->ISR register reads 0x00000002 (the TCIF Transfer Complete Interrupt Flag is set, and there are NO Transfer Errors). However, the destination buffer remains completely filled with 0x00000000. [Troubleshooting Done] To isolate the issue, I have verified the following, but the problem persists: CPU Read/Write Test (Pass): Before triggering the DMA2D, I forced the CPU to write 0xDEADBEEF to the destinatio

Hello, I am working with the following setup: Board: B-L4S5I-IOT-01A MCU: STM32L4S5VIT6 BLE Module: BlueNRG-M0+ (in built in the Kit) I am currently facing an issue related to the BLE MTU (Maximum Transmission Unit) size. By default, the payload length is limited to 20 bytes, which is insufficient for my application, as my data length exceeds 180 bytes. I would like to know: Is there a way to increase the MTU size on the BlueNRG-M0+? Can this be achieved without modifying my existing data transmission mechanism (i.e., without manually fragmenting the data into smaller packets)? My goal is to transmit larger data packets in a single operation, if supported. Any guidance or recommended approach would be highly appreciated. Thank you.

Title edited to clarify this is about CMSIS-RTOSHello, everybody!I don't know where to look for information on which CMSIS versions are supported by specific STM32 microcontrollers. I asked one of the ST employees and STM32 Sidekick about this, and I got no definitive answers.STM software tools confuse me further. For example, STM32CubeMX (6.17.0) allows me to choose CMSISv2 the interface for FreeRTOS in my STM32F769I‑DISCO board project, but LwIP in the same project does not see the operating system used unless I change the CMSIS version to v1 (you can find more details about this specific issue in this thread). I couldn't find any document that would say which interfaces are supported by LwIP either.That's why I would like to ask You, where should I look for information about which CMSIS versions are supported by specific STM MCUs and, ideally, middlewares and software packages?

I am working with STM32N6570-DK. My code is building fine , suddenly a hard fault has started coming. I have tried updating firmware, resetting the board, unplugging and reconnecting it, But debugger is getting stopped after sometime.