Product forums

Hi everyone,We are encountering a XSPI Deadlock on our STM32H7S7-Discovery board (STM32H7S78-DK).To provide some context, our system is configured as follows:External FLASH: Connected to XSPI1. Swapped through XSPIM to port 2 and operates in memory mapped mode. MCE1 is activated across the entire address range using the AES-STREAM Cipher.External PSRAM: Connected to XSPI2. Swapped through XSPIM to port 1 and operates in memory mapped mode. MCE2 is activated across the entire address range using the NOEKEON-BLOCK Cipher.The issue occurs when running an LZO decompression algorithm. The algorithm reads compressed data from the PSRAM and writes the decompressed output back to the PSRAM, while the code is being executed on External FLASH.At some point during decompression, the core completely freezes, no HardFault or BusFault is triggered, and the debugger permanently loses its connection to the core.We have tried multiple approaches to resolve, including the official er

In TouchGFX 4.26.0 image order changes in application.config even if those images don't change.This causes unnecessary changes to show up in git: Feature request is to either preserve the order or to have them always lexicographically sorted.

I want to design according to the Figma design, but I have no clue.How can I make the menu follow the selection in the simulator? If I want the last menu to scroll down.

Hardware: STM32G473QETXHAL Version: STM32G4 HALI2C Mode: Slave mode using HAL_I2C_Slave_Seq_Receive_IT()Application: DS1307 RTC emulation Issue DescriptionWhen implementing an I2C slave device (DS1307 RTC emulation), we observe that HAL_I2C_ErrorCallback() is consistently called with error code HAL_I2C_ERROR_AF (0x00000004 - Acknowledge Failure) at the end of successful write transactions from the I2C master Transaction FlowMaster sends START + Address (0x68) + WRITESlave ACKs (address match detected)Master sends data bytes (8 bytes total)Slave receives all bytes correctly via HAL_I2C_SlaveRxCpltCallback()Master sends NACK (to signal end of write)Master sends STOPHAL_I2C_ErrorCallback() is called with HAL_I2C_ERROR_AFHAL_I2C_ListenCpltCallback() is also calledExpected BehaviorAccording to I2C protocol, the master sending NACK at the end of a write transaction is normal behavior to signal "I don't want to send more data." This should not be reported as an e

Hi,I am at the beginner/beginning stages trying to pick up STM32 ecosystem involving touchGFX and a display board STM32H7S78-DK. For now I would like to interact a touch button on screen to turn on an LED.Could I get guidance on the overall workflow if it is correct:1) touchGFX - generate UI and generate code2) open up STM32CubeIDE and import touchGFX generated .cprojects and other supporting files3) edit .ioc file to set LED pin (PO1) as output (active-low). save and generate code4) stm32CubeIDE -> build and run -> LED PO1 turns on but my display goes blankover at touchGFX when I try to regenerate code it states [generate code failure] Could I get some guidance thanks. 

Hi,1. can we interface directly ST4SIM-200S with LTE modem? 2. how we will integrate service provider like airtel/jio please share me any readable document that how it works with cellular network. 

Just posting this incase it helps someone with this problem that I encountered recently.I just update to new windows 11 laptop so I started going through the laborious process of installing all my tools including the latest STM32Cube programmer v2.22. Figured this would be a good time to update everything since I'm installing everything fresh anyway.The issue I encountered is that v2.22 will connect and program the STM32 MCUs just fine but if I try to run the Serial Wire Viewer SWV I get no print outs. I tried a lot of things like reinstalling windows drivers and reinstalling the software but none of that worked, slowing clocks down and other stuff. In the end I removed v2.22 and installed v2.20 and that fixed the issue immediately. #bug-report 

HI,as we understand, TouchGFX does not provide support for mulitple layers, even though many targeted STM32 controllers do.We need to display a live image from the camera (at maximum possible frame rate) and overlay some gaphics on the top of it. Kind of OSD. What is the best/recommended way to achieve this task with TouchGFX? Is it feasible to do so with TouchGFX at all or the resulting performce will suffer too much?What do we do with StemWin - the hardware LTDC Layer 0 is used for the camera live image, while Layer 1 is for any graphics over the latter. Neither of two get affected by each ohter and very high frame rate is achievable without visible performance degradation.What solution TouchGFX may offer for similar tasks? Thanks.If it is matter:The display resoltion is 800x600, the camera image is a standard grayscale PAL 720x576

Hello,TouchGFX seems to have some sort of a “bug”, where in PORTRAIT orientation the text will glitch with some weird white lines, unless there is an image in the item-tree situated ABOVE text items. It doesn’t have to be any image in particular, but MUST be an image.If there isn't any image added, then every text element is glitched the moment I rotate to PORTRAIT:touchgfx::HAL::getInstance()->setDisplayOrientation(isPortrait ? touchgfx::ORIENTATION_PORTRAIT : touchgfx::ORIENTATION_LANDSCAPE);The glitched text looks as such (see the white weird lines corrupting the text):This is my item tree in TouchGFX Designer (I also tried removing the background but the white lines remained):Then, if I add any kind of image, any text area under that image in the designer stack-up, it will be displayed without glitches and any text area placed above will glitch as such (Note, the XY location in the screen does not affect this, only the stack-up arrangement!):This is the stack-up to produce such

Hello, I'm trying to create a project with custom model via STM32 Cube AI studio, which uses STedge Core AI v. 3.0.0. Validation is performed on STM32N6570-DK. I'm getting following error:E200(ValidationError): TARGET: Unable to bind the ST.AI runtime with "network" c-model: [] E801(HwIOError): Invalid firmware - COM7:115200 When running same command from command line I see that progress goes to 74,8 % and then stucks until error is displayed.See attached failed report for details. 

I am using a custom PCB design with a 480x800 pixel RGB input LCD display. I am driving the display via the LTDC peripheral. When I change the default colors, the color on the screen changes accordingly, which indicates that there is no apparent hardware issue with driving the LCD.However, when I try to display a simple text on the screen using TouchGFX, the system enters the DMA2D_XferErrorCallback function due to a DMA2D error. Because of this, the text cannot be rendered on the display.Could you please explain the possible reasons for this DMA2D transfer error and what might be causing it? best regardsCelil Bayrakdar

  Hi, Currently I face problem that TouchGFX 4.26.0 use a lot of PC RAM up to 9GB RAM Project info: Resolution 480x800 Number of screen 26 Number of custom container 82 Support language: 5 Typographies: 25 With the same design for resolution 272x480 use up to 3GB RAM How can I reduce number of RAM usage? Thanks, Phat

Hello ST Community,I'm trying to connect via UART instead of ST_LINK to the NUCLEO-H755ZI-Q, but it just won't connect.First, I connect the 3.3V pin to BOOT0, and it activates in bootloader mode. Then, I click "Connect" in the STM32CubeProgrammer environment, and I get this error:The UART's RX and TX (it's a USB SERIAL CH340) are connected to the Arduino pin PD5 and PD6 (USART2) of the NUCLEO-H755ZI-Q. Pin GND are also connected correctly. The settings on the STM32CubeProgrammer are as shown in the photo:Why isn't it connecting, or is there something wrong?thanks for supports

There have been great improvements to TouchGFX  Designer and the build process.  It now cleanly allows integration into the STM32CubeIDE project structure.  The problem is that even though you can provide a project name and the output will be placed in a folder with that name, the .IOC file always has the same name as every other project made with the same device.  My workflow from the Designer, to CubeMX to CubeIDE is painless.  Generate code, then allow CubeMX to open the project and it's imported into CubeIDE.  The first project is great.  If you go back to Designer and create a different project with the same device, the process breaks down.  You'll have the same project as the last project as far as CubeIDE is concerned.  Now if you create a new workspace for each project, you can get all of your projects imported albeit you have to switch workspaces.  You can at least name them, so you know what project you're working on.  No

Hello everyone, I’m working on a custom version of the FP-SNS-DATALOG2 firmware and attempting to integrate a new sensor, LSM6DSV320X, which is available on the STEVAL-SensorTile.Box Pro but not on the STEVAL-STWINBX1. To add support for this sensor, I performed the following changes: Added Drivers/BSP/Components/lsm6dsv320x/lsm6dsv320x_reg.c/.h Integrated corresponding PnPL + App Model .c/.h files Added that sensor task Modified: DatalogAppTask.c/.h App.c/.h sysdebug_conf.h SensorManager_conf.h HardwareDetect.c/.h Updated existing DTM(Device Template Model) from stdatalog-pysdk pnpl module(FP-SNS-DATALOG2-9.json) to include the new sensor Removed ism6hg256x from the build With these changes, I’m able to start logging using a custom device template, and the sensor appears to work initially. However, the system becomes unreliable after a reset. Main Issue The board operates correctly until it is reset. After reset, I encounter multiple faults, including: HardFaults Bus faults

I am using the STM32L433 MCU and both the HID and VCP interfaces are not working even though the DFU is.I am simply using the STM32CubeMX software to generate a standard default USB Setup but I keep getting the same Windows USB Error "USB Device Not Recognised" which is the "Device Descriptor request failed".My hardware is a custom design and believe that I have the correct differential impedance or the DFU would not have worked. VBUS is at 3.3V (<4V)D+/D- traces > 2 inches but differential impedance has been matched to 90 Ohms using Altium.I have a 12MHZ Crystal, the MCU can run Crystal-less.USB is 48MHz but runs from RC, also used PLLSA1 from HSE.STM32CubeIDE v2.1.1MX_USB_DEVICE_Init() called. If the DFU is working then why not the other USB Interfaces?

Hello,I'm stalling with an issue with Optee on a custom board with 256 MB of ram and an STM32MP135D.The environment was working with the DK (MP135F and 512M ram).I followed the guide for the configuration with 256 MB of ram (https://wiki.st.com/stm32mpu/wiki/How_to_configure_a_256MB_DDR_mapping_from_STM32_MPU_Distribution_Package), however it panics as soon as optee starts.Am I missing something or do you have some hints?Thank you NOTICE: CPU: STM32MP135D Rev.Y NOTICE: Model: STMicroelectronics custom STM32CubeMX board - openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06 ERROR: nvmem node board_id not found INFO: PMIC version = 0x21 WARNING: VDD unknown WARNING: stm32_rng_init: No RNG found in device tree. NOTICE: Reset reason (0x35): INFO: Power-on Reset (rst_por) INFO: FCONF: Reading TB_FW firmware configuration file from: 0x2ffe0000 INFO: FCONF: Reading firmware configuration information for: stm32mp_fuse INFO: FCONF: Reading firmware configuration information for: stm32mp_io INFO:

Hello,I came across the following problem: whenever firmware writes some data to flash memory, the NRST pin doesn't work. I mean, when low level is asserted on NRST pin the device starts to run software not at 0x0800... address but at 0x1FFF.... The same happens in the debugger: when I press "Reset the chip..." button. I get the message: "Break at address "0x1fff5236" with no debug information available, or outside of program code."The data is written to flash memory page which is  not used by the running program code. Data is correctly written and no error is shown in the FLASH->SR register. I didn't change any option bytes. The device runs at 80 MHz, BOOT0 pin is grounded. What am I doing wrong ?

 Hi everyone,I’m currently working on a camera preview pipeline on the STM32MP257F-DK using the Sony IMX335 (MIPI CSI-2) sensor.One important point is that STM32MP2 uses a media-controller-based camera architecture (DCMIPP + CSI subdevices). Because of this, Qt Multimedia cannot directly detect the MIPI camera as a standard /dev/videoX capture device. For that reason, I am using libcamera as the capture backend. It correctly handles the media graph configuration internally and exposes a usable video stream to GStreamer, which makes camera streaming stable and reliable.The functional pipeline is working. However, the goal is to display the live feed inside a Qt6 QML application with proper GPU acceleration, and this is where I am facing a major performance bottleneck: CPU usage is very high during preview, while the Vivante GPU remains mostly idle.I’d really appreciate guidance from anyone who has implemented a zero-copy GPU camera pipeline on STM32MP2.Platform OverviewBoard:

Hi Team,I am working with the STEVAL-SPIN3202 evaluation board and facing an issue while trying to flash firmware to the target MCU.Setup Details:Board: STEVAL-SPIN3202Programmer: Onboard ST-LINKTool: STM32CubeIDEIssue Description:ST-LINK is detected in STM32CubeProgrammer but not able to connect to the target MCU STM32F103CBT6Programming fails consistentlyPFA, Kindly suggest to resolve this issue.Thanks,HimansuSmall Signals India Pvt. Ltd

Hi,We are looking for a WiFi module or preferably a WiFi + BT module to be used in a battery-operated device where audio files are recorded onto a uSD card and whenever required they are downloaded through WiFi or BT link to a PC. For context, the audio files are 20MB in size.These are the main specs:- pre-certified module: WiFi or WiFi+BT- highly reliable for mass production- uSD card interface (specific for audio and files)- means to record and play back the audio files- low-power - compact & SMD- straightforward to integrate from a firmware perspective (library available) and well supported in terms of documentation and ecosystem.Could you please make recommendations:- for such suitable modules?- for alternative system architecture using ST products and ecosystem to implements such device?Thank youRicko

I am trying to debug a project I have created in STM32CubeMX and edited in STM32CubeIDE with the STM32MP257F-DK. I am seeing an intermittent error which is mentioned in the troubleshooting grid, but it's not clear to me how to fix it.  After it builds with no errors, I get a familiar message:Error in final launch sequence:Failed pre launchFailed pre launchFirmware remoteproc load failed, please:1. make sure that /lib/firmware on your target has space2. make sure that /lib/firmware has write access> you can open a Console View for this..When I check dmesg on the board, I see the lines[ 58.546876] remoteproc remoteproc0: powering up m0[ 58.628708] remoteproc remoteproc0: Booting fw image Project_Name_CM33.elf, size 3097880[ 58.631958] remoteproc remoteproc0: bad phdr da 0x80100000 mem 0x540[ 58.638236] remoteproc remoteproc0: Failed to load program segments: -22[ 58.645251] remoteproc remoteproc0: Boot failed: -22This "bad phdr" line is mentioned in Table 1 of the troublesho

I am using STM32G0B1KCT6 MCU, i would like to use the full flash of 256KB starting from 0x8000000 to 0x803FFFF. but am unable to flash in bank 2 (ranging from 0x8020000 to 0x803FFFF).if i reduce the flash size to Bank1 only, then am able to flash and run the code.I am aware its default dual bank MCU. PFA code snippet for changing it to single bank.Also tried changing it single bank using the stcubeprogrammer but still fails to flash the MCU.   void ConfigureFlashToSingleBank(void) { FLASH_OBProgramInitTypeDef OBInit; HAL_FLASHEx_OBGetConfig(&OBInit); /* Check if Dual Bank mode is enabled */ if (OBInit.USERConfig & FLASH_OPTR_DUAL_BANK) { HAL_FLASH_Unlock(); HAL_FLASH_OB_Unlock(); OBInit.OptionType = OPTIONBYTE_USER; /* Disable Dual Bank (enable linear 256KB flash) */ OBInit.USERConfig &= ~FLASH_OPTR_DUAL_BANK; if (HAL_FLASHEx_OBProgram(&OBInit) == HAL_OK) { HAL_FLASH_OB_Launch(); // triggers reset } HAL_FLASH_OB_Lock(); HAL_FLASH_Loc

HiI need help in erasing the device: STM32H735IGK3, This device is getting erased only till sector 0.There were total 8 sectors.I am following the steps given in  Reference manual for erase operation but still it didn't work.Could you please suggest something to resolve this issue with Erase?Or please point out the reason which is throwing this issue.Thanks!Saista 

Hi,I hope you are doing well. I am currently developing a project based on the STM32WBA55CGU6 MCU. The hardware design (PCB) and firmware have been developed and validated using this device, particularly relying on its BLE capabilities and STM32_WPAN stack. However, I am currently facing a supply issue, as the STM32WBA55CGU6 appears to be out of stock across major distributors and local suppliers in Türkiye (e.g., Digi-Key EKOM). I would like to kindly ask: 1- Is there an estimated timeline for restocking or production availability? 2- Are there any recommended drop-in or near drop-in alternatives within the STM32WBA series that can be used with minimal hardware and firmware modifications? Thank you very much for your support.