STM32 MCUs

I have a question regarding an F407 wake-up error. I am using an F407ZGT and have connected the power switch to PA0 using a pull-down resistor. HAL_SuspendTick(); HAL_PWR_EnableWakeUpPin( PWR_WAKEUP_PIN1 ); __HAL_PWR_CLEAR_FLAG( PWR_FLAG_WU | PWR_FLAG_SB ); HAL_PWR_EnterSTANDBYMode(); I have been using this code successfully. However, after modifying the firmware and downloading it, or when downloading via the gang tool, the MCU fails to wake up via the wake-up input—though not always. Once this issue occurs on a board, the wake-up function permanently stops working, regardless of any operations performed. Is there any way to restore the wake-up function? Please help me!

This is in relation to post "Strange behavior with STM32G474QE pin PB4(Solved: Re: Strange behaviour with STM32G474QE pin PB4 - STMicroelectronics Community)" I'm facing the issue of PB4 going high for 27ms approx after MCU reset. My design is freezed, And this pin is connected to a relay which turns ON when this pin goes high. The relay turn on time is 7.5ms. Is there a solution in code initialization so that this pulse stays below 7.5ms. I'm attaching the waveform. 

Hi everyone,I am working on STM32H723 (H7 series) using HAL, and I am facing an issue with ADC1 + ADC2 dual regular simultaneous mode.Configuration DetailsMCU: STM32H723HAL based projectADC1 = MasterADC2 = SlaveMode: ADC_DUALMODE_REGSIMULTDualModeData: ADC_DUALMODEDATAFORMAT_32_10_BITSResolution: 12-bitScan mode: DisabledContinuous mode: DisabledTrigger source: TIM2_TRGO (rising edge)DMA: Circular modeADC3 runs independently (also TIM2 triggered) and works perfectlyDual mode started using:HAL_ADCEx_MultiModeStart_DMA(&hadc1, (uint32_t*)g_adc12_packed_buffer, TP_DMA_BUFFER_SIZE); Buffer unpacking:  uint32_t packed = g_adc12_packed_buffer[i]; uint16_t adc1_raw = packed & 0xFFFF; uint16_t adc2_raw = packed >> 16; Observed BehaviourWhen I apply voltage to ADC1 input:Both ADC1 and ADC2 values changeBoth show identical values (mirrored)When I apply voltage to ADC2 input:No change in readingsADC2 does not respondWhen inputs are floating (level shifted mid-sca

I am new to using stm32 MCUs and I was following a youtube tutorial on how to set up a debugger for dual core MCUs. Before changing some settings I was able to start the debugger without any errors. Now when I try to run the debugger I get this error window popup:'Launching file_CM4 Debug' has encountered a problem. Error in final launch sequence:Failed to start GDB server When I click on details I get:Error in final launch sequence:Failed to start GDB serverFailed to start GDB serverError in initializing ST-LINK device.Reason: (4) No device found on target. I also noticed that when I plug the controller in the USB port and open NOD_H755ZIQ in This PC, it has 4 files (it had 3 files before). New file is called FAIL.TXT and it says: The interface firmware FAILED to reset/halt the target MCU This is the youtube tutorial that I followed : https://www.youtube.com/watch?v=jI1k6p-fduE Can anyone help me with this?Is it possible to fix this problem or do I n

In CubeMX2 when configuring the I2S peripheral on an STM32C542 running from a clock of 144MHz and selecting an audio clock rate of 96000Hz, CubeMX2 computes a nearest reachable frequency of 97826Hz (I2SDIV = 23, ODD = 0). When code is generated and run on actual hardware, the HAL2 I2S driver computes a different value of 95744Hz (I2SDIV = 23, ODD = 1). The HAL2 hardware value has less error from the desired 96000Hz than the value reported by CubeMX2, but the CubeMX2 value may be used in designing other aspects of the firmware and result in unexpected performance.    

Hello,I am working on a custom PCB using the STM32H757IITx. While programming the chip with an ST-LINK/V2 SET programmer via STM32CubeProgrammer, I encounter the warning::warning: “The core is locked up”:cross_mark: Mass erase / flash operation failedAs a result, the board does not operate normally.Here is the log output:Error in final launch sequence: Failed to execute MI command: load D:\XXX\XXX\XXX-v1.0\CM7\Debug\Integra-v1.0_CM7.elf Error message from debugger back end: Error finishing flash operation Failed to execute MI command: load D:\XXX\XXX\XXX-v1.0\CM7\Debug\Integra-v1.0_CM7.elf Error message from debugger back end: Error finishing flash operation Error finishing flash operation.I have attached screenshots of the error for reference.Has anyone encountered this issue or can suggest possible solutions?Thank you.   

I have a self-contained widget (a rectangle of 360x60) which has a draggable mixin and a custom handleDragEvent.void WarningModal::handleDragEvent(const touchgfx::DragEvent& event) { if (!draggingEnabled || !animator) return; int16_t newX = animator->getX() + event.getDeltaX(); // Hard clamp: never allow leftward movement past the resting position if (newX < WARNING_MODAL_VISIBLE_X) newX = WARNING_MODAL_VISIBLE_X; animator->moveTo(newX, WARNING_MODAL_Y); }Basically it can only be dragged from left to rightI'm noticing that, if I try to move it up and down, I'm able to generate a wobbling movement up and down because, the widget tends to return to its WARNING_MODAL_Y due to the modeTo line.Is there a way to disable the drag for an axis to get a smooth movement right-left or up-down

The STM32 toolchain based on gcc 13.3 already supports a lot of C23 features, e.g. constexpr. This is really awesome.But the current version of CubeIDE seems not to be able yet to parse these new features, so syntax checking / highlighting / code linking breaks.Is there any simple workaround for this? Or is there information available, whether the next version of CubeIDE will update this?

Hi I have a project with STM32F446RET6 which has custom bootloader and application in user defined location. This project does UART Bootloader for firmware upgrade - issue faced is if the device loses power while in between the firmware upgrade then the device is neither in UART bootloader/DFU mode nor has a valid firmware. The solution which i want to implement is keeping two image of the application in two slot A and B. Normal working in Slot A  and backup in Slot B. Firmware upgrade happens in Slot A and if fails copy the firmware from Slot B otherwise copy Slot A to Slot B. can anyone provide a simple logic which can be implemented to check if the firmware upgrade is completed and successful in SlotA. I would not like to add CRC check.

I’m starting to work with the STM32F411E‑Discovery board and I’d like to use it for real‑time audio filtering. I’m using the onboard MEMS microphone together with the mini‑jack audio output.I’m currently struggling with configuring the clock settings correctly — I’m observing a variable timing drift between the microphone input and the audio output.Could you advise on the proper clock configuration for this setup, or point me to an existing project or example that demonstrates real‑time audio processing on the STM32F411E‑Discovery?

Hi,On the stm32c5 nucleo board (NUCLEO-C5A3ZG) there is T1S OA PMD driver (not mounted?).  In the header file "stm32c593xx.h" exists a 10BASE-T1S control register "MAC10BT1SCR". But there is no documentation in the Reference Manual RM0522 Rev 1, and I can't find a way to enable T1S on MXcube2.Can anyone help me here? Is the T1S PDM really integrated in the C5 series?I would really like to experiment with 10Base T1S.RegardsPatrick

Hello, everyone,I am currently working on a project using STM32WB07CC. During the design of low power consumption, I found that when waking up the MCU from the deepstop mode through the wakeup pin, it is impossible to obtain the wakeup source by accessing PWRC->SR1&SR3. However, when waking up through the RTC, it is possible to obtain the source. After referring to the demo provided by ST, I also discovered the same issue.I hope everyone can help me solve this problem.thank.

Hi all, I've noticed that a DHCP client can not get an IP address from the server if both mDNS server and DHCP client are enabled. The reason seems to be in ST Ethernet driver (nx_stm32_eth_driver.c): static UINT _nx_driver_hardware_initialize(NX_IP_DRIVER *driver_req_ptr) { ... FilterConfig.BroadcastFilter = ENABLE; ... } static UINT _nx_driver_hardware_multicast_join(NX_IP_DRIVER *driver_req_ptr) { /* Increase the multicast count. */ nx_driver_information.nx_driver_information_multicast_count++; /* Enable multicast frame reception. */ FilterConfig.PassAllMulticast = ENABLE; HAL_ETH_SetMACFilterConfig(&eth_handle, &FilterConfig); /* Return success. */ return(NX_SUCCESS); } In _nx_driver_hardware_initialize() FilterConfig is just prepared, there is no HAL_ETH_SetMACFilterConfig() call. That's why DHCP works OK if mDNS is not used. If mDNS is active, it calls _nx_driver_hardware_multicast_join() and applies a prepared&nbsp

I am using the STM32H733 controller along with the NetXDuo networking stack. The issue started after updating the HAL drivers in my project from version v1.11.0 to v1.16.0 (released on February 24, 2026).After this update, I observed that when the device boots up and no network activity occurs for a certain period (for example, no ping requests are sent to the device or device sending any UDP packet), the Ethernet connection is eventually lost permanently. Once this happens, the device becomes unreachable over Ethernet, and neither a soft reset nor a hard reset restores the connection.However, if the device receives a ping immediately after booting, or if it sends a UDP packet shortly after startup from the device, the Ethernet connection remains stable. In this case, normal operation continues without any issues until the device is reset again and no network activity is observed for a certain period as well.This problem only appeared after updating the HAL drivers to version v1.16.0 a

Hi,recently in STM32CubeProgrammer was introduced the Serial Numbering feature, which is much appreciated.However, it's limiting because the serial number is assigned manually, setting a starting value that is progressively incremented.In a production site with multiple test stations, it becomes difficult to synchronize the various stations on the SN to be used.Hence my request: it would be very useful if the Serial Numbering section were integrated with a "Script" field, in which the user can enter the filepath of a custom "C-style" script (or in the programming language of ST choice) whose return value is the SN to be programmed. The script (customizable by us) will provide the correct return value, based on the logic the end company wishes to use to assign the SN to its devices (e.g., databases, *.csv, etc.). Hoping for a future update, I look forward to hearing from you.Best regards,Matteo

Hi, I need to use a 5V external clock for an stm32g473. The datasheet in table 39. High-speed external user clock characteristics says Vhsel is max Vdd, but Table 12. STM32G473xB/xC/xE pin definition says PF0 / OSC_IN is FT_a (five volt tolerant). Is it safe to use an external 5V clock ? Thx, 

Ok, this is perhaps esoteric, so maybe there is some research out there.   I am looking at STM32U3 or STM32C5, but the problem applies to pretty much all CM33 based ST MCUs.  The bus matrix implies a fast multiplexor for GPDMA (and SDMMC) to SRAM1. So unless dealing with burst transfers to SRAM (yes, SDMMC does that, and the GPDMA channels with the 32 byte FIFO could do that if the transfer is a multiple of 4 bytes), this fast multiplexor seems to save 1 clock reducing a beat to 2 clocks (if somebody has details for AHB vs. APB, that would be interesting). So to minimize latency and maximize bandwidth, DMA buffers (.dma section) should go into SRAM1.    So if DMA goes into SRAM1, then should not all the stacks go into SRAM2 ? I would assume burst DMA to/from SRAM1 would introduce some additional latency, especially in the way for ISR stacking / unstacking. Is this just overthinking this, or is that measurable ?   Now some U3 parts have SRAM3. One thought is to

Can I join a LoRaWAN network only once?so that after a software or hardware reset, i would not need to join the same network once again I am working with LoRaWAN_End_Node_LBM example

I am currently working on the STM32N6570-DK board and need guidance on FSBL configuration, multi-layer project structure, and external flash programming.Issue 1: FSBL Peripheral ConfigurationI enabled multiple peripherals in FSBL:USART1, I2CBSPXSPI1, XSPI2CSI, DCMIPPVENC, JPEGAfter enabling these, I am getting an "unsupported relocation" error.Kindly guide:Which peripherals are recommended to enable in FSBLWhich peripherals should be initialized in the Application layer insteadProper distribution of initialization between:FSBLApplicationExternal Memory LoaderIssue 2: Multi-Layer Project UnderstandingCurrently, the project has:Three separate layers (FSBL, Application, External Loader)Each has its own startup file and main functionI would like to understand:How these three layers work togetherExecution flow between FSBL → ApplicationHow memory mapping and control transfer happenThere are three separate build outputs—which one should be flashed?How will all three sections work together in

I would like to connect a 12-bit ADC operating at 10MSps to the PSSI interface of the STM32N657 device.  There is some confusion as to the nature of the clock source. The reference manual indicates that this may be either an input or an output.  If configured as an output, what is the source of the clock?  Examples suggest that a PWM timer needs to be used.  Here is an illustration of what I would like to do:Do I need to use the PWM timer as the clock source?

Hello everybody.I try to convert an STM32CubeIDE project into a CMake project to be used on VSCode using the procedure included in "STM32CubeIDE for Visual Studio Code" extension.The procedure aborts with this error message:  [Error] [ide-project-convert] Bad escaped character in JSON at position 15583 (line 322 column 55). Line 322 of "stm32cubeide-export.json" file, created by the procedure itself, is this one:, "option.includepaths": "-I\"C:\Repo_mgo\STM32Workspace\NGDrive\Appl\dDrive_Fwk2\application\Display\TouchGFX\generated\texts\include\", -I\"C:\Repo_mgo\STM32Workspace\NGDrive\Appl\dDrive_Fwk2\application\Display\TouchGFX\", -I\"C:\Repo_mgo\STM32Workspace\NGDrive\Appl\dDrive_Fwk2\application\Display\TouchGFX\gui\include\", -I\"C:\Repo_mgo\STM32Workspace\NGDrive\Appl\dDrive_Fwk2\application\Display\TouchGFX\generated\gui_generated\include\", -I\"C:\Repo_mgo\STM32Workspace\NGDrive\Appl\dDrive_Fwk2\application\Display\TouchGFX\generated\fonts\include\", -I\"C:\Repo

I am currently working with the LoRa-E5 Mini module based on the STM32WLE5JC microcontroller, and I am using STM32CubeIDE version 2.1.0 for development. I have successfully tested basic GPIO functionality (LED blinking), and I am now trying to implement LoRa-based communication (transmission and reception) using the integrated SubGHz radio. However, I am facing challenges in properly configuring and utilizing the SubGHz_Phy middleware and radio drivers within STM32CubeIDE. Specifically, I need guidance on the following: The correct procedure to enable and configure the SubGHz radio peripheral in STM32CubeIDE for STM32WLE5JC. How to properly include and use the SubGHz_Phy middleware for basic LoRa communication. Availability of any official example projects (such as Ping-Pong or Tx/Rx) compatible with STM32CubeIDE 2.1.0 for the LoRa-E5 Mini module. Proper configuration of radio parameters (frequency, spreading factor, bandwidth) for reliable communication. Any recommended steps to ensu

Hello,I am using VSCode on Windows with the STM32CubeIDE for VSCode extension.Before installing the extension, I had already installed and configured these tools separately on my system:CMakeArm GNU Toolchain (arm-none-eabi-gcc, arm-none-eabi-gdb)clangdAfter installing the STM32CubeIDE for VSCode extension, build works, but debug fails to start. I get the following popup error:bound doStepStartGdbClientDebug Failed: Failed to get gdb version.I would like to ask whether this issue may be related to how the extension detects GDB, conflicts with environment variables, or path priority when multiple toolchains are installed.Observed behaviorI already had a standalone ARM toolchain installed before installing the STM32CubeIDE for VSCode extension.After installing the extension, debug no longer starts correctly.The popup error is:bound doStepStartGdbClientDebug Failed: Failed to get gdb version.My current suspicion is that the extension is either:not finding the correct arm-none-eabi-gdb, or

I have a STM32WB05TZF6TR. All VCCs are running off 1.8V. I'm trying to use PA8 and PB5 with 3.3V 10k pullups. But the signals are being clamped at 2.5V. I had expected this not to happen, as they are supposed to be 5V tolerant. Does anyone know what's happening here? There's nothing connected to the pins besides the pullups. I have a bare STM32CubeMX project, with just this GPIO init:void MX_GPIO_Init(void){ GPIO_InitTypeDef GPIO_InitStruct = {0}; /* GPIO Ports Clock Enable */ __HAL_RCC_GPIOB_CLK_ENABLE(); __HAL_RCC_GPIOA_CLK_ENABLE(); /*Configure GPIO pin : PB5 */ GPIO_InitStruct.Pin = GPIO_PIN_5; GPIO_InitStruct.Mode = GPIO_MODE_INPUT; GPIO_InitStruct.Pull = GPIO_NOPULL; HAL_GPIO_Init(GPIOB, &GPIO_InitStruct); /*Configure GPIO pin : PA8 */ GPIO_InitStruct.Pin = GPIO_PIN_8; GPIO_InitStruct.Mode = GPIO_MODE_INPUT; GPIO_InitStruct.Pull = GPIO_NOPULL; HAL_GPIO_Init(GPIOA, &GPIO_InitStruct); } Much appreciated,David 

(I've opened an issue on GitHub on this matter already, but I was asked to post it here again...)Hey there,I'm currently developing an audio application based on the STM32N657 MCU. I have already implemented a working version of this application on an STM32U5A5 MCU, but now I need to port it to the N6.The application receives a PDM audio stream from a MEMS microphone via SAI. The audio data is then converted to PCM using the PDM2PCM library. On the STM32U5A5 MCU, the application uses the CM33 variant of this library (libPDMFilter_CM33_GCC_wc32.a), but I cannot find a variant of this library for the CM55 of the STM32N6 in any of the STM32Cube firmware packages.I would be very grateful for any advice or help on this matter!Thanks in advance and best regards,Jens