Automotive and Transportation

I have an eMoticom eM007 ECU on a motorcycle which has been developed from the SPC5-L9177A-K02 dev kit. I wish to connect to the ECU to download the bin file so I can learn to tune it. The ECU has a canbus connector with 4 pins +12v, Gnd, CAN-H, and CAN-L. I have purchased the ST-Link-V3MODS board with the view of using the bridge CAN interface to connect to the ECU. How should this be connected as the Bridge CAN only has logic signals Rx/Tx using pins 9 and 10 on CN2. Any help will be appreciated as I don't want to brick the ECU on connection.Will I be able to use the STM32CubeProgrammer to download the bin file from the ECU and re-flash it once the edits to the tune have been done. Also will it be possible to write on the fly.

Hi, I followed the instruction in AN5171 to integrate windriver into the SPC5Studio DE. When compiling an existing sample project for the SPC574K-DISCOVERY (SPC574Kxx_RLA PWM Test Application for Discovery) with the windriver diab compiler, it will throw a lot of errors. 1. Once the windriver plugin setup is correctly done, should all the autogenerated mcal code be directly compilable with diab, or is that not supported?2. What must be done to configure SPC5Studio to generate diab compatible c-code? Best regardsNorbert

3-Phase motor control with industrial products.

hello~ I am using the spc58ec disp chip and want to continuously send CAN messages of different cycles. Here is the code what i wrote: //// void send_10ms(){     uint32_t rv;     CANTxFrame msg_10ms;     msh_10ms.ID = 0x11U;     msh_10ms.DLC = 8U;     msh_10ms.data32[0] = 0x1234U;     rv = can_lld_transmit(&CAND2, 0, &msg_10ms);     osalThreadDelayMilliseconds(10); } // and also have a similer fcuntion which send 100ms can message //// I want them to send in different cycles. The above can messages can only be sent in 100ms, how should they be modified? Thank you~  

I am using the SPC58 MCU product with the TRACE32 debugger. When changing the Life Cycle from "customer_delivery" to "in_field" with the trace32 script, debugging is only possible by entering the keycode. What should I do if I want to change the Life Cycle back to "customer_delivery"?

Hello, I am currently struggline with flash program with some tools.The tool send 62byte data with CAN FD and I want to write down it.I am using SPC5Studio with Flash_driver (ssd_c55.h)* FILE NAME : ssd_c55.h ** DATE : December 19, 2011 ** AUTHOR : FPT Teamand the function exported.extern UINT32 FlashProgram ( PSSD_CONFIG pSSDConfig,     BOOL factoryPgmFlag,     UINT32 dest,     UINT32 size,    UINT32 source,    PCONTEXT_DATA pCtxData);I modify  the eeprom_lld.c as bleow for programming the software. I checked that the len=8U works. (8U is defined in examples.)If the len is set to 6, it is not work. in case of 4 then it is partly works. (4byte date programmed and 4bytes are skipped). Are there any way to write down the data with variable length?uint32_t eeprom_lld_flashprogram(uint32_t address, uint64_t buffer, uint32_t len) {   uint32_t returnvalue;   uint32_t bufferpointer;  &nbsp

Hi, Good day. This is third party for programmer.Our customer requires the programming for SR5E1-176, and we need the programming guide to develop the programming board and algorithm. Could you help to share the programming guide to me?or Please let me know if we need to sign NDA. Thank you. Jack 

Hello,I want to build a simple application (like a UART message, GPIO bit-bang etc.) targeting SR6G7 and running on a custom board. To support that I want to use the latest SDK 3.3.0 and flash the code via StellarLINK.Is there any guide how to add the SDK resource to the StellarStudio?Thanks in advance!

Hi Team,          In this module(TESEO-LIV4f) can able to processing the data L5 band(NACIC data and IRNSS)And how to update the firmware  for l5 band(navic and Irnss) and pls give refrence.And any break out board avaliavle for this module(TESEO-LIV4F)?Thanks and regardsARavind.S.R

I am using the SPC58 MCU product with the TRACE32 debugger. When changing the Life Cycle from "customer_delivery" to "in_field" with the trace32 script, debugging is only possible by entering the keycode. What should I do if I want to change the Life Cycle back to "customer_delivery"?

How to execute demo of sensorless Field oriented control in SPC560PL5 MCU and L9907 evaluation kit. There are three demos available1 single shunt motor control2 standard motor control3 thee shunt motor control Which one should I select for sensorlessWhenWhen I disable hall sensor I'm getting issue

I have tried to integrated imported examples in spc5 studio. I unbaled to done . Is there any setting you can help me..!!. I have used stm32cube IDE for stm32 series microcontrollers, it is very flexible and easy . Right now i am using spc570sxx series controller, and IDE is SPC5 studio IDE. Please help to integrate imported example applications.

Hello, I would like to know how to configure Clock with SPC570S50E1, using internal RC oscillator.I would like to have maximum clock for each components. Currently, I succeed to set maximum system clock, but for ADC it is 1.6MHz while maximum is 12MHz.How to accelerate ADC clock? 

I have recently procured a X-NUCLEO-GNSS1A1 on its own. I would simply like to use the LIV3F to test the LNA/SAW filtering along with different antennas as well. I am able to connect the LIV3F to Teseo Suite via FTDI -> UART. I can see all of the satellites and NMEA data being streamed by the receiver, but I am unable to change any settings. I need to update a couple of settings, but the LIV3F is not detected, and it is shown in Teseo Suite as a 'generic' device, instead of a LIV3F, or LIV3FL, etc.  Any assistance would be much appreciated, I feel that I've exhausted every resource I have trying to change the settings. fwiw, I have a couple of custom PCBs with LIV3Fs installed on them, and I do not have this issue with those boards. Only the LIV3F on the X-NUCLEO-GNSS1A1. 

Hello,I am able to receive data normally when connecting USB with Teseo Suite, but when I connect using Terminal software, there is no data output at all. I am sure the baud rate is 460800. Is there a specific command I need to input for it to start outputting data?I am using "Teseo EVB".The connection with Teseo Suite is normal, and the data output is also normal:However, when I use Terminal software to connect, there is no data output at all:Is there a specific command I need to input for it to start outputting data?Thank you.  

Dear,I have SPC58N that writed wrong password on it, is it possible to blank memory and reprogram it with new software containing known password?Using PLS debug and JTAG Adaptor,regards,

HiI came across  “AEK-AUD-C1D9031” which contain “SPC582B60E1”. For this I am looking for Flashing tool and Debugger with software.While searching for flashing tool and Debugger with software, I came across “SPC5-UDESTK USB/JTAG adapter” and  “SPC5-UDEDEBG for a perpetual, full-feature, unlimited code-size license”. Mean while I came across the UAD2pro. Can anyone  please explain "UAD2pro" and how can I use it. Regards,E shiva shankar

Hello, I am currently using SPC58EC80 with SPC5Studio.I have some problem to load the data located in ROM area to RAM area when boot. I am using " > CAL_RAM AT > CAL_ROM" command for loading the data from 0x013A0000 to 0x400B0000.I check the RAM area after booting the SPC58EC80 but no data are loaded from 0x400B0000. If anyone try to success to load the data when booting with link scrpit, please guide me.I also write down rom.c contents at the end. Here is contents of link script and its name is user.ld. I delete application.ld file on purpose.MEMORY{       flash (rx)             : org = 0x00FC0000, len = 4M - 128k      CAL_ROM (rx)    : org = 0x013A0000, len = 128k     MEA_RAM (rxw)   : org = 0x400A8000, len = 32k    CAL_RAM (rxw)   : org = 0x400B0000, len = 128k    ram (rxw)            &nbsp

Hello community users! There is a question that needs to be asked. Any help would be greatly appreciated! We want to know Can S2_LP UHF module receive the differential correction data generated by our own gnss base station? So we'd like to know the supported protocols as well as a description of the format. Can S2-LP support transparent protocol? We need to use the tuning method + baud rate + bandwidth that it supports.

For starting with development on SPC56ELxx what I need is:the discovery board : https://www.st.com/content/st_com/en/products/evaluation-tools/product-evaluation-tools/mcu-mpu-eval-tools/spc5-automotive-mcu-eval-tools/spc56l-discovery.htmlSPC5 Studiohttps://www.digikey.com/products/en?WT.z_cid=sp_497_0928_buynow&Enterprise=44&lang=en&Vendor=497&mpart=SPC5-UDEDEBGhttps://www.digikey.com/products/en?WT.z_cid=sp_497_0928_buynow&Enterprise=44&lang=en&Vendor=497&mpart=SPC5-UDESTK-PLUSBetween 3 and 4 is not clear for me if one is the hardware debugger and one is the license, so I have to buy both, or one of the two is sufficient. Thanx

Hi there,after installing SPC5Studio v6.0 and opening some sample projects (even an empty one) for SPC582Bx mcu, I found no way to alter compiler and linker options.In eclipse-based IDE (like SPC5Studio) this is normally accomplished opening the project Properties, under C/C++ Build/Settings. Please note that sample projects generate and build fine; I have no board to try UDE debugging but this is outside the scope of the current question. Is there some other way to change compiler and linker flags? Thanks for the support,FP

Which one is the best spc5 board to get for engine and dashboard data collection,usage and sensors integration and communication and also compatible with autosar framework 

Hello,How can I check that the teseo correctly receives L5 band satellite and not only L1?Is it indicated in a NMEA message?Best regardsMich

Is there an input field for the used shunt value or offset? If not, where can I manipulate the code? 

Hello,In document UM3009 §7.3  =>Multi-constellation firmware supports the following constellations: GPS, GALILEO, GLONASS, BEIDOUand QZSS. All constellations cannot be enabled at the same time, allowed combinations to achievemaximum coverage, are: (GPS+GALILEO+QZSS+GLONASS), (GPS+GALILEO+QZSS+BEIDOU) and(GLONASS+BEIDOU). Any constellation can be enabled as standalone satellite navigation system.Does that means it is impossible to have GLONASS and BEIDOU at the same time? Best regardsMich