STM32CubeProgrammer (MCUs)

..

Good evening to you all electronics dark wizards.To the point:I am interested in flashing specific pages of stm32 chips because im locating some custom binary config files for my application.I found the option in my stm32cubeprogrammer v2.6.0 to define the Start Address but the data input box cannot be used for some reason?

Hi,I am developing some code for a display interface on a NUCLEO-H755ZI-Q, I debug some basic code and the STM32 seem to have crashed.Now I can not connect anymore to it, not even with the CubeProgrammer V2.5.Is there a way to recover the Nucleo board from this?

I'm using the STM32429I-EVAL board and STM32CubeProgammer and can program the board when the program is located in internal flash.When I edit the app to use the external flash I get a good compile in STM32CubeIDE but the programmer will not load the bin file 'Error while reading the file'.So I can't program the board.ANyone had this and solved it please?

Hi all,I am new here and to STM32 in general.Does the STm32F401CE comes from the factory with a DFU bootloader?If so, does a full chip erase with the CubeProgrammer and a stlink v2 erases that factory bootloader?.If so, is the binary of the factory bootloader available so it can be flashed back into the device? I can't get the DFU bootloader recognized by the CubeProgammer, if it's because of the full chip erases I performed, I wonder if I can program the stock bootloader back. Below is a snapshot of a memory dump of of the bootloader area, I think. I am using STM32F401CE with a 25Mhz external crystal, and everything else works.

Thank you for helping.​environment:​STM32CubeProgrammer Ver2.6.0TouchGFX Ver4.15.0Board: STM32F769I-DISCO etc.​Is it possible to write a hex file created by TouchGFX using STM32CubeProgrammer?​I want to write a program to internal and external flash via UART without using SWD.​Thank you.

HalloSince i installated STM32CubeProgrammer the DfuseDemo no longer works.I found out that the driver is the Problem.When i use "STM32 Bootloader" --> STM32Cubeprogrammer find the µC but DfuseDemo don´t.When i use "STM Device in DFU Mode Version: 3.0.6.1" --> DfuseDemo find the µC but STM32Cubeprogrammer don´t.In the development department we use stm32cube programmer. However, dfuseDemo is to be used in other departments and by the customer.Is there a possibility to use both software without changing the driver?Could the latest versions of the programs agree on one (or both) drivers?

Problem running STM32CubeProgrammer Version 2.4.0 on Mac OS Version 10.10.5.Keeps throwing error "CubeProgrammer_API or one of its dependencies is missing. Please try reinstalling the program or check your java architecture"java -version returnsjava version "1.8.0_251"Java(TM) SE Runtime Environment (build 1.8.0_251-b08)Java HotSpot(TM) 64-Bit Server VM (build 25.251-b08, mixed mode)Please help. Thanks in advance.

We use several operations with the CLI tool to configure and program our device. The final operation sets the RDP for code protection.Following this, we see:Warning: The core is locked upThis is confirmed by the code not executing (non responsive).On the dev board, hitting a reset button doesn't seem to clear the problem.In the product itself, the unit is sealed with battery permanently connected, so power cycle isn't possible.Have tried adding -s option without success.Everything works prior to the final step of setting RDP:STM32_Programmer_CLI -c port=SWD reset=Hwrst freq=8000 -s -ob RDP=187(187 is 0xBB)Suggestions?

Hi,i have a custom board based on stm32f769. We are updating the firmware for the same on field using DFU over USB interface. Recently we have added QSPI external flash to store data and graphical assets and we are able to flash the binary using stm32cubeprogrammer over stlink with the help of external loader. Now we want to support the similar programming method using DFU over USB. Kindly tell us how we can do the same? can we add support for flashing external QSPI flash in any DFU enabled utility / stm32cubeprogrammer or any other way except JTAG/ debugger.

Hi,I would like to know how to reset the discovery kit to the default setting?And how do I know about the current setting (write protection is enabled/disabled)in the discovery kit?The reason is that,I suddenly can't run anything on my board(even just an LED toggle), I am confused about what I have done.The only thing I remember is to set the write protection address by the STM32CubeProgrammer as the photo. Is it caused by this? I have tried this, but it seems didn't work.1.Full chip erase by STM32CubeProgrammer2.Download STM32 ST-LINK Utility, but it's can't connect to my board.Thank you.

Because I do not have access to the BOOT0 pin (custom board, not eval board) I have used the software method of branching into the bootloader : https://stm32f4-discovery.net/2017/04/tutorial-jump-system-memory-software-stm32/I have adpted this code for the device (notably bootloader address 0x1FF0 0000)USART2 physical pins are PA2 and 3My questions are:Is the bootloader code listening to USART2, is it listening to everything? Or does this require a specific configuration?Do I need to configure the USART2 with baudrate etc. before jumping to the bootlaoder so that it corresponds to the CUBE->UART settings or is this an automatic process?____logs from Cube15:59:33:510 : Serial Port COM34 is successfully opened.15:59:33:511 : Port configuration: parity = even, baudrate = 115200, data-bit = 8, stop-bit = 1.0, flow-control = off15:59:33:511 : No Init bits value is : 0 15:59:33:511 : Sending init command: 15:59:33:511 : byte 0x7F sent successfully to target15:59:34:511 : Wait en

Launching the app from the bin directory doesn't work either and there are no errors in the terminal. It just silently fails. I believe part of the problem is the update to version 2.6.0 which uses its own bundled JRE. Perhaps there is a conflict with the OpenJDK (Amazon Corretto) JRE installed on my machine. However, it is necessary to have JRE on my machine to run STM32CubeMX and STM32CubeIDE. I tried to download the previous version (2.5.0) and run that. It does not launch either, however, there are errors in the terminal. ~ % /Applications/STMicroelectronics/STM32Cube/STM32CubeProgrammer/STM32CubeProgrammer.app/Contents/MacOs/bin/STM32CubeProgrammer ; exit; Exception in Application start method java.lang.reflect.InvocationTargetException at sun.reflect.NativeMethodAccessorImpl.invoke0(Native Method) at sun.reflect.NativeMethodAccessorImpl.invoke(NativeMethodAccessorImpl.java:62) at sun.reflect.DelegatingMethodAccessorImpl.invoke(DelegatingMethodAccessorImpl.java:43) at java.lan

I'm working with STM32H743 and W25Q128 external flash drive. I am trying to develop external loader. When I test with STM32CubeProgrammer and .bin files, everything works fine, writes to 0x90000000 address, verifies and reads OK. When I try to upload .elf

A Windows application that writes multiple binary files at once because you have to write multiple binary files to STM32WB at once. Is developing. I can write a binary file to FLASH using CubeProgrammer_API, I can't find a function in CubeProgrammer_API to write a binary file for FUS/RF Stack. Is there another API? Can you tell me if there is one? Also, if you have sample code, could you please tell me?

Hello thereI am using the official engineering code Thread_SED_Coap_FreeRTOS. When downloading with STM32CubeProgrammer, the error message connection to device0x495 is lost appears. At this time, the program should fail to download because the LED1, LED2, and LED3 on the board are not lit, so I want to use it again When downloading programs on this board, STM32CubeProgrammer reported an error ERROR:NO STM32 TARGET FOUND. What is causing this? I downloaded other project codes normally.THANK YOU

Hi,I just bought the STM32MP157F-EV1 and was trying to get it started.I tried to followed the manual written in the website and I thought I have completed step 4 and step 5 in the manual.However, when I tried to populate the SDCard, I realize that I forgot to install Java before installing the STM32CubeProgrammer.So, I tried executing the commands in the manual.However, the result is as follows:I am using Ubuntu 20.04 and I have read that a lot of people are having the same problem as I am.I tried these steps that I found on stackoverflowHowever when I try to reinstall the program and run it, it still shows the same message.Does anyone know how to solve this problem?

Hello,I try to connect to a STM32G431 Device over JTAG. I got the following error. Has someone a solution for this error?

Hi,We're currently using the SWO viewer in the old ST-Link Utility in Windows.However, this is a bit inconvenient for us because our main development is in Linux. Is SWO support planned for STM32CubeProgrammer? Even just STM32Programmer_CLI SWO support would be much appreciated.

Hi,Almost all demos are not able to run and display on STM32F769i-DISCO using v2.6.0.Below is the terminal logYou may also refer to https://community.st.com/s/question/0D53W00000O1KHJSA3/run-target-on-stm32h747idisco-failed Run Target Generate Done Generate Assets make -f simulator/gcc/Makefile assets -j8 Reading ./application.config Done Post Generate touchgfx update_project --project-file=simulator/msvs/Application.vcxproj Done Post Generate Target touchgfx update_project --project-file=../STM32F769I_DISCO.ioc --platform=m7 Done Compile make -f ../gcc/Makefile -j8 Reading TouchGFX/application.config Linking TouchGFX/build/bin/target.elf Producing additional output formats... target.hex - Combined internal+external hex intflash.elf - Internal flash, elf debug intflash.hex - Internal flash, hex extflash.bin - External flash, binary Done Flash make -f ../gcc/Makefile flash Reading TouchGFX/application.config Linking TouchGFX/build/bin/target.elf Producing addi

Thank you for helping.environment:MCU: STM32F769BIProgrammer: stm32CubeProgrammer Ver2.6.0I booted with the BOOT pin of the MCU set to H level and tried to write the hex file by the boot loader using USART1.It's progressing halfway, but I always get an error and the write fails.What is the cause?Attach the log file.Thank you.

i am getting the same error with cube programmer version 2.5.0i am using windows 7 32 bit.Java JRE build 1.8.0_271-b09i have tried all the solutions given in previous posts but couldnt get past this.the user manual of cube programmer 2.6.0 says :"There is no need to install any Java™ SE Run Time Environment since version 2.6.0. TheSTM32CubeProgrammer runs with a bundled JRE available inside the downloadedpackage and no longer with the one installed on your machine."please help

I want to make a Tool like STM32CubeProgrammer using MFC.When I checked the device monitoring, STM32CubeProgrammer was able to communicate 2K at a time.When connected via USB, the device manager shows up as STM32 BOOTLOADER, I am trying to connect this and the tool.Is there any way to know the communication protocol or API?I'm sorry if this was an absurd question.

i am using windows 7 32 bit.Java JRE build 1.8.0_271-b09i have tried all the solutions given in other posts but couldn't get past this.the user manual of cube programmer 2.6.0 says :"There is no need to install any Java™ SE Run Time Environment since version 2.6.0. TheSTM32CubeProgrammer runs with a bundled JRE available inside the downloadedpackage and no longer with the one installed on your machine."please help

I want to program the FW via UART.Read and erase function are working fine, but write function is not working with below error message.Anybody has a knowhow about this problem? 14:35:12 : Port configuration: parity = even, baudrate = 115200, data-bit = 8,           stop-bit = 1.0, flow-control = off 14:35:12 : Activating device: OK 14:35:12 : Chip ID: 0x460  14:35:12 : BootLoader protocol version: 3.1 14:35:14 : UPLOADING OPTION BYTES DATA ... 14:35:14 :  Bank     : 0x00 14:35:14 :  Address    : 0x1fff7800 14:35:14 :  Size     : 52 Bytes 14:35:14 :  Bank     : 0x01 14:35:14 :  Address    : 0x1fff7870 14:35:14 :  Size     : 4 Bytes 14:35:15 : UPLOADING ... 14:35:15 :&