STM32 MCUs

Hi, I’m using a NUCLEO-144 (STM32H563ZIT6) development board with only the board USB STLINK-V3EC port connected. TRACE and DEBUG are enabled with Serial Wire in the configuration file, and printf is routed through ITM: int _write(int file, char *ptr, int len) { for (int i = 0; i < len; i++) { ITM_SendChar((*ptr++)); } return len; } SWV is enabled in the debug configuration, the core clock is 250 MHz, and the SWV window (port 0) shows output correctly in STM32CubeIDE.     When I switch to an external ST-LINK/V2 and connect NRST#15 / SWDIO#7 / SWCLK#9 / GND#20 / TARGET VCC#1 / VDD3.3 V#19, programming and debugging work, but the SWV window shows nothing in the STM32CubeIDE. The reason for using ST-LINK/V2 for SWV debugging is that on our product’s onboard MCU, only VDD, NRST, SWDIO, SWCLK, and GND are exposed.   Could anyone explain why SWV output does not appear with ST-LINK/V2? Thanks.    

Hi everyone,I’m currently working on a project using an STM32 Nucleo L476RG and a Velleman VMA302 Bluetooth module (HC-05 type), and I’m trying to send data over Bluetooth to my Mac.I configured USART1 at 9600 baud in STM32CubeIDE, and my code is continuously sending a simple message like "Hello". The module is powered and appears to be working (LED is blinking, pairing works with my Mac).On macOS, I can see the Bluetooth device and pair with it successfully. I also see the serial port (e.g. /dev/tty.HC-05-xxxx), but when I try to read data using the terminal command:screen /dev/tty.HC-05-xxxx 9600I don’t receive anything.I’ve already checked:TX/RX connections (crossed correctly)Baud rate (9600 on both sides) Bluetooth pairing (successful)What I’m trying to achieve:Send data from the STM32 to my Mac via Bluetooth and read it as a serial stream.My questions:Is there something specific to configure on macOS for Bluetooth serial communication?Could the issue come from the STM32 confi

Is this version do not copy touchgfx_core.a to project folder? ex) Middlewares\ST\touchgfx\lib\core\cortex_m4f\IAR8.xbecause I did generate code in touchGFX so automatelly remove the files in lib/core.and i can't build on IAR because .ipcf file generated from touchGFX desinger need touchgfx_core.a of path above.

I have a STM32WB55 board where I have two I2C connections:1. LSM6DSO IMU2. TCA9548A with downstream I2C to hall sensors The TCA9548A I2C multiplexer does not ACK when addressed. The firmware scans 0x70 (this should be correct already)–0x77 and gets no ACK. The LSM6DSO IMU on the same MCU works, so the MCU is fine; only the TCA9548A path fails. the A0, A1, A2 are all grounded, RESET pin is pulled up to VCC with the appropriate resistor, VCC and GND are wired correctly as well (~3.3V). TCA on PB8 (SCL) and PB9 (SDA) pins of the STM32WB55, each with 4.7k pull-up resistors to VCC. I even changed the PB8 PB9 pins to software I2C and back to hardwawre I2C, but no luck; I did even deeper diagnosis, and it is just that TCA9548A never ACKs at any address 0x70–0x77.  The data is collected via BLE, the exact steps since I obtained the PCB are as follows:1. Upgraded firmware on:> FUS: stm32cubewb-v1-24-0\\\\STM32Cube_FW_WB_V1.24.0\\\\Projects\\\\STM32WB_Copro_Wireless_B

Hi   I would like to check if it is necessary to call MX_RNG_Init() after the MCU exits STOP MODE to reconfigure the RNG?   BR Gilberto

When will the NUCLEO-C5A3ZG  be available via distributors?The st.com site lists it as available(mass production), but none of the distributors has listed it at all. And the estore lists it as coming soon. Do you have any more concrete dates, will it be available anytime soon?   Best

I'm using STM32F2xx, STM32F4xx, STM32F7xx and STM32L0xx firmware supplied by STM32CubeMX. I need to generate an SBOM for cybersecurity purposes. Can ST provide that or provide documentaiton that can be referenced to generate the SBOM?

Hey all, I've used this tutorial: https://youtu.be/suMytEyQTP4?si=jLtyF5uH1Qd6zpYvto run TouchGFX on several different MCUs/boards such as the black pill or NUCLEO-F446RE. However, I simply cannot get anything to display when I setup TouchGFX on my NUCLEO-WL55JC2. I'm unsure if there is something I'm missing that makes it unfeasible or much more difficult to get it running on the board, but I'm at my wit's end after debugging for hours and finding no issue. The code compiles and programs to the board fine, and I've verified all connections as well as parameters, and I am at a loss as to what to do. If anyone could help I would greatly appreciate it. (Note: I've tried in single core setup to get it to work as well and that did not seem to solve the issue.)

I downloaded the STM32C5 software package from st.com, but I am unable to use IAR. How can I import the CMake project?

Hello,With the new STM32Cube Debug Jlink GDB Server V1.2.0 I'm not anymore able to start the debugging session. If I downgrade to V1.1.0 then it is working again. I get always the error message "No GDB Server running". I tried that with my old launch.json settings and with the new generated and adapted json settings.Do I miss some special settings or has the new extension a bug?Or do i need any dependency? error message: old launch.json new launch.json  Thanks in advance,nobody 

Hello,in our design with STM32H753ZIT6 I've adjusted the C0G load capacitors on the LSE 32.768 kHz crystal so that the real-time clock is now very accurate (less than 1 second error in 24 hours). I've always performed the calibration in VBAT mode at a voltage between 2.3 and 3.2 V.However, now I've noticed that in normal VDD mode with active controller, the real-time clock is running significantly too slow, with an error of 90 seconds in 24 hours. I've ruled out the VBAT supply voltage as the cause. Any ideas what could be causing this large error in normal VDD mode?Thank you!

There is no USBX or other middleware in my cubemx2, but the connection introduction indicates that it is available. How to access middleware & utilities - STM32CubeMX2 1.0.0 documentation    

Hi ,Recently I got a NUCLEO-C051C8 board and tried to connect it to windows and program it using STm32CubeIDE but it does not show that st-link is connected , ST-link on board blinks RED continuously. Cant install it ( installation goes through , but cant see it in device manager ) using stsw-link009( https://www.st.com/en/development-tools/stsw-link009.html?dl=redirect ) Cant connect using STM32CubeProgrammer. Tried 2 USb cables , various ports of pc but  in vain. Can someone please help ?   

Hi    For some of my project, I need to measure the power consumption of the STM32N6570-DK while running a model on the CPU only versus an NPU + CPU accelerated workload.   I am following the guide  1. How to measure power on the STM32N6 - STMicroelectronics Community 2. STMicroelectronics/x-cube-n6-ai-power-measurement: An AI software application package implementing low-power optimizations and enabling power measurement on STM32N6 DK board.​   Based on these documents, I plan to measure the current via CN2 pins 3 and 4 while powering the board through CN6 (USB-C).   My Question:Does measuring current at this point (CN2 pins 3 & 4) isolate the consumption of the NPU and CPU (VDDCore)? Specifically, I want to know if this measurement will include the power draw from the camera module and LCD display if they are active in the same project.   Any guidance on isolating th

The STM32CubeIDE project output setting is not present in STM32CubeMX2. Is there a way to generate a project that STM32CubeIDE can use? How do I do this? I did try the "CMake" option but wasn't able to get a project to import correctly.

안녕하세요 STM32N6570-DK의 사용하기 위한 cubemx 설정이 필요합니다. 카메라, lcd, sd카드, usb, eth 등 기능을 다 살린 cubemx 설정 또는 ioc 파일을 받고 싶습니다. 확인 부탁 드립니다.   Hello, I need a cubemx setting for use of STM32N6570-DK. I would like to receive a cubemx setting or an ioc file that utilizes all the functions such as camera, lcd, sd card, usb, eth, etc. Please check it.

Hello all,I've been using this U5 chip for a couple of years but I am just now trying to update all of the packages to start working on the project again.  I have the U5 firmware at 1.8.0, AZRTOS-H7 at 3.5.0 (I'll explain why I mention that), FileX is 6.4.0 and the CubeIDE is 2.0.0.When I started this project, I was using an H7 chip and that is where the Azure implementation started.  Now things seem integrated and those choices in the software packs selection in CubeMX don't seem to matter...I assume.  The H7 package is the one still loaded to my hard drive.  I've tried creating a new project and setting everything up again but nothing has changed from my original project.  I tried to apply some U5 patch with version 2.2.0 or something like that.  MX took it and made it disappear into the void.  Again, maybe I don't need to care about manual package setup anymore.ThreadOS works great and everything has been working great for me.  I added USBX, F

Hello i use STM32G070CBT6 with PD0 and others pins.PD0 as input pin with no internal pull-up/down with extrenal 10k pullup gives only 0.7V, when i set the pin to output and set state to high there is 3.3V.Where is the problem? 

Dear ST Community,I am currently migrating my Firmware from STM32H723VG to STM32H563VI. I have problem with Internal Temp Sensor. Based on Reference Manual on both MCU reading temperature is the same, but it doesn't work as it should.When on STM32H7 I got about 750 (24 degree Celsius) on reading ADC from TEMP Sens, on STM32H5 I have around 100.I tried both with and without cache (ICache and DCache), with Bare Metal and Zephyr RTOS code. In every configuration it is not working. I tried also on different MCUs, so it shouldn't be part itself.It worked with Nucleo H563ZI, but doesn't with H563VI.What else can I do?

According to Page 1354 of rm0394, setting LDMA_TX bit must occur only when SPE=0.However, from my reading of the function HAL_SPI_Transmit_DMA, this bit may be set or cleared when the DataSize <= 8bit and MemDataAlignment == HALFWORD, even if SPE=1.This looks like a bug.Am I correct?STM32Cube MCU Package for STM32F4 STM32L4, version 1.28.3

Hi,among probably many other registers, the ITM registers like TCR and Stimulus Port Registers described in the ITM programmers model in ARM Cortex-M7 Processor TRM are missing. Which means I either have to adapt the svd file or go to memory view and translate and modify the registers manually. Is this on purpose and or are there plans to fix this? If you have a repository somewhere I can maybe fix that on my own and start PR.Ty in advance

I am setting up my STM32F303RET6 for four differential inputs to be sampled simultaneously. As seen in the screenshot attached. there is no option for differential inputs on CubeMX. Am I missing something here? I have reset whole project to ensure no pins are assigned elsewhere.

Hi I have a USB-C Connector that will be used for Power Delivery Sink  for charging and USB Full Speed Mode(12Mbps) for communicating with onboard STM32F767ZIT6. But only one thing will happen at a time.    As seen in the attached schematics, I have used STUSB4500 as PD Sink controller. I will communicate with it via I2C using STM32. I understand that this STUSB4500 will negotiate 20V(60W which i want for charging) with the source(which in this case is AC-DC Wall adapter) in Power Delivery Mode. But my question is during USB Full Speed Mode Communication with STM32, when that USB-C Receptable is connected to a PC instead of Wall Adapter. As during charging mode, USB_VBus is 20V and in Full Speed mode, it is 5V and my STM32 is Self-Powered and VBus sensing is mandatory. But due to USB VBus varying between 5V and 20V, I cant connect it to for example PA9 VBus sensing pin of STM32 using a voltage divider.  So, i was thinking maybe there is another option to sense

Hello,I want to change for boot to use XSPI1 interface, but I am not sure about OTP bits, there in description some bits is not very clear, what OTP bits to set to switch if it's possible ?Additionally if I will use SD card for boot I can set OTP11 value to 0x00000020 (bit5 = 1 = sdcard), write FW to sd and use sd for boot source ?Thanks.

Hello, I tried to program a MSD on an STM32C071. My computer "sees" the USB device but didn't recognized it as a storage device. I use the NUCLEO-C071 and have setup the following: RCC:High Speed Clock(HSE): Crystal/Ceramic Resonator Clock Configuration:Input frequency: 8HCLK: 48ToUSB(Mhz) HSIUSB48: 48 CubeMX USB:Mode: Device_Only,USB interrupt enabled CubeMX USBX:UXDevice memory pool size: 1024*5USBX Device Generate Core Init code: yesUSBX Device System Stack Size: 1024*5 In CubeIDE:main.c: /* USER CODE BEGIN 2 */ MX_USB_PCD_Init(); // Line 94 /* USER CODE END 2 */ /* USER CODE BEGIN USB_Init 2 */ HAL_PCDEx_PMAConfig(&hpcd_USB_DRD_FS, 0x00 , PCD_SNG_BUF, 0x20); // Line 180 HAL_PCDEx_PMAConfig(&hpcd_USB_DRD_FS, 0x80 , PCD_SNG_BUF, 0x60); HAL_PCDEx_PMAConfig(&hpcd_USB_DRD_FS, 0x81 , PCD_SNG_BUF, 0xA0); ux_dcd_stm32_initialize((ULONG)NULL, (ULONG)&hpcd_USB_DRD_FS); HAL_PCD_Start(&hpcd_USB_DRD_FS); /* USER CODE END USB_Init 2 */ In ux_device_msc.c /* USER CODE BEGIN P