STM32 MCUs Products

Hello ST experts,I configured an STM32H745 dual core to read data from ADC1/ADC2 in dual mode. I dedicated the M7 core to initialize ADCs, timer and DMA. But after running the code it seems that the ADC is not working either DMA.  I used the similar code on the STM32H750 single core. The code is correct.I think I have to configure extra settings for dual core such as managing the memory. Could you please help me.The DMA is in circular mode with "Word" data length.TIM2 triggers the ADCs. 

Hi ST team,Is VREFINT in STM32C011F4P6 internally fixed and stable, independent of VDDA fluctuations?If VDDA fluctuates (for example due to LDO load or battery discharge), will the ADC raw readings change proportionally because ADC reference = VDDA?Is it officially recommended for STM32C0 users to read VREFINT periodically and compute real VDDA to correct all ADC channels, especially when VDDA is not stable? Example : - ADC accuracy change if VDDA fluctuation like 3.3v to 2.9v. ? or it can take ref from Vrefint ?

I am trying to create a signal that changes its frequency in dynamic way using timers  but i am having some issues to do it can anyone give me some tips for easy implementation to do this task

Hello, I would like to enable overdrive mode on my N657X0. This chip supports 800MHz operation but is usually limited to 600MHz. The manuals specifies to enable overdrive mode before configuring the CPU clock to reach the maximum frequency. I was wondering if there are any - for beginners like me not obvious - ways for the chip or its peripherals to get damaged when enabling overdrive mode. Kind regards, Len

Hello,I have found an inconsistency in the documentation for the STM32U031K8 MCU on ST.com:The Reference Manual (RM0503), Revision 4 is listed on the documentation page, and Table 22 in RM0503 Rev 4 indicates that LPUART2 does not have wake-up capability.The Data Sheet (DS14581), Revision 2 is also listed, and Table 3 in DS14581 Rev 2 states that LPUART2 does have wake-up capability.This leads to a contradiction between the reference manual and the data sheet regarding the wake-up capability of LPUART2. Based on this, it appears that the data sheet documentation might not have been updated properly for this MCU.Could you please review and update the documentation links so that they are consistent and correct for the STM32U031K8?Thank you.

Hi Team,We are currently working with a custom board that uses the STM32H745BIT6 MCU, and we are attempting to connect it to the STLINK-V3SET debugger. However, we are experiencing intermittent debugging issues described below:The debugger successfully enters debug mode only 2–3 times when done the first time.In most cases, the debugger connects and enters debug mode, but after approximately 6–8 seconds, it displays a “Target lost” error (please refer to the attached photo).Often, it shows “Target not responding.” When this happens, we need to power cycle the board. After turning the power supply off and on again, it behaves as described in point 2.This issue has become a major roadblock in our development process.Could you please advise if we might be missing something or configuring anything incorrectly? If you require any additional information from our side (errors, logs, etc.), please let us know and we will provide it.Best regards,Prathiksha

Our Engineering team is currently having difficulties getting our onboard STM32F303RB MCU to enumerate as a USB DFU device when entering Bootloader mode. We require this functionality in order to be able to upgrade our firmware out in the field. We are able to have our application firmware enumerate a USB device but no luck with the bootloader. The STM32 communicates to an Embedded Linux Host via a USB Hub: Embedded Linux Host <-> USB Hub <-> STM32 We have a few questions regarding getting the bootloader to enumerate. On the internet there appears to be mixed messages as to whether the STM32F303RB MCU uses an internal pullup when in the Bootloader. Are you able to confirm whether it does enable an internal pullup for the bootloader? I have set BOOT0 HIGH but there is also mixed messages about BOOT1 being pulled to GND. To enter USB DFU mode does BOOT1 have to be pulled to GND or is it a don't care and can be left floating? Is there some kind of output/pin I am able to prob

STM32H7R7L8H6H XSPI2 is mounted with MX25UM25645GXDI00, and the frequency setting exceeds 133Mhz. The Boot program fails to run and gets stuck in the "XSPI_WaitFlagStateUntilTimeout" function.Please help me!XSPI2 ConfigurationClock Tree ConfigurationEXTMEM_MANAGER Config 1EXTMEM_MANAGER Config 2Stuck here

USB Issues with STM32F767-ZIT – Project StatusI’m an amateur working on building an electronic device. Currently, I’m in the planning and prototyping phase and creating my own PCB design. My current project is based on the STM32F767-ZIT, and I’m having trouble getting the USB (USB-B) connection to work.Hardware SetupPower: VBUS is powered through a ferrite from 5 V on the female USB-B jack.Data lines: D+ and D- are connected to PA11/PA12, each with 22 Ω resistors.GND: connected to the board.HSE: 8 MHzWires: relatively short, nothing unusual.Current BehaviorWhen connecting to a PC:Windows plays the device connect sound, and a device appears in Device Manager.The device shows as “Unknown USB Device (Device Descriptor Request Failed)”.Properties:Device type: USB ControllerManufacturer: Standard USB Host ControllerStatus: “This device has been stopped because it reported problems (Code 43)”USBView shows: FailedEnumeration: Unknown USB Device (Device Descriptor Request Failed)Oscilloscope O

I'm working on a custom STM32U5 board and I'm trying to harden the system.I followed the AN5347 (https://www.st.com/resource/en/application_note/an5347-arm-trustzone-features-for-stm32l5-and-stm32u5-series-stmicroelectronics.pdf) in particular I followed the chapter 10 with success as I was able to raise up to RDP=2 with OEM password and back to RDP=0.Then I tried for the second time using the STM32CubeProgrammer instead of the command line as described in the application note, but I got some issues at step 5: Set RDP level 2. The STM32CubeProgrammer did not end the process and got stuck writing RDP=0xCC in the option byte and after ten minutes I forced the termination of the GUI.After that I was not able to recover to RDP=0.Every time I try to send a command to the board I get some error.If I try to follow chapter 10.6 Unlock RDP level 2 with OEM2Key with the command line:STM32_Programmer_CLI.exe -c port=swd mode=UR -unlockrdp2 0xMYKEYLOW 0xMYKEYHIthe result i

Hi! I'm trying to muddle my way through a project in which I'd like to use an stm32u5 MCU. I would like to extend the RAM/FLASH of the MCU by using PSRAM and eMMC; it seems that higher densities of PSRAM require being run at 1.8V, so I am imagining powering at least the digital side of the MCU with a 1.8V rail. My application also involves motor control; I'll be using the STSPIN233, which can also be powered by a 1.8V rail. I would like to perform current sensing, and here's where my question comes in. I'd like to use a current sense amplifier, e.g. TI's INA181 (or similar). These devices need a 3.3V rail for power. I am curious whether it is better to:Power the analog domain of the stm32u5 at 3.3V. The current sense amplifiers + shunt resistors are scaled such that I produce a total rail-to-rail voltage near 3.3V, biased at 1.65V.Power the analog domain of the stm32u5 at 1.8V. The current sense amplifiers + shunt resistors are scaled such that I produce a total rail-to-rail

Hello Team,   One more query is there. We are not using USB. In STM32H7S7L8H6 pin D9-VDD50USB is there. So, can we connect it with 3.3V supply?   Thanks & Regards, Jignesh Karena

Hi everyone,I am currently facing a very frustrating issue while trying to interface an AP Memory APS51208N (Octal PSRAM) with an STM32H723 via the OctoSPI peripheral.To avoid reinventing the wheel, I recently refactored my initialization code to use the official ST aps512xx library (https://github.com/STMicroelectronics/stm32-aps512). I'm using read and write latency set to 7.Unfortunately, the peripheral is still not working properly, and I am experiencing three distinct, highly erratic behaviors:1. Weird Register Read Pattern When I try to read the memory control registers using the BSP functions, the returned values are incorrect and seem to form a repeating sequence rather than actual register data. Here is what I get for MR0 to MR8:Array[0] (MR0) = 0x08Array[1] (MR1) = 0x89Array[2] (MR2) = 0xDAArray[3] (MR3) = 0xA0Array[4] (MR4) = 0x08Array[5] (MR8) = 0x892. OctoSPI Deadlock (Free-running) If I execute the initialization and read sequence continuously (free-running), the Oct

Dear,  Can you confirm that OCTOSPI P2 is available only on WLCSP208 and TFBGA216 packages of this series?  I wanted to use both OCTOSPI interfaces in LQFP144, but noticed that there is missing only OCTOSPIM_P2_IO3 line in it, so my conclusion is that LQFP144 supports only one OCTOSPI. Is that right?  Thank you. 

Hello everybody, I am new here so please let me know, if there is important information missing. Thank you already for you time! I set up a STM32U575I-EV board for communication with CAN. The STM Board, a PCAN-USB dongle and an Oszilloskope are connected to the bus. The Bus is terminated correctly with two 120 Ohm resistors. I use the HAL libraries to interface with the FDCAN peripherie. The jumpers from the eval board are set to connect PB9 and PB8 with the CAN transceiver and to disconnect PB8 from the USB-C PD-interface. To test the setup I send dummy frames (ID: 0x000, DLC: 1, Data: 0x00). The frame is visible on the Bus and also the ACK from PCAN is visibile. PCAN USB has a 200mV higher voltage on CAN High 0 level. Here is the dummy frame on the Oszi: As you see on the the screenshot, the ACK is there and even though I put only one message in the Tx-Buffer of the FDCAN, it retransmitted. Here is my code: main.cint main(void) { /* MCU Configurati

I am currently evaluating microcontroller options for our project and need your support in identifying a suitable MCU.Our key interface requirements are as follows:   2× MDIO interfaces,3× I2C bus interfaces If you could recommend an MCU that supports these features or share any relevant technical details/datasheets, it would be very helpful.If not, please also suggest alternate part numbers that can meet this requirement.

I am a fan of STM32, especially the peripheral sets offered are great. Over the years however, one type of peripheral is missing which would be a great help for many projects, this is a programmable logic cell.Such a cell would contain elements like Flip-Flops, Look Up Tables and such that can be configured for specific functions. For instance using the LUT's, it would be possible to create all kinds of logic operations like AND, OR, XOR gates.Using the Flip-Flops, I would be able for instance to create a clock gate, which I needed in my last project. There I needed an external clock signal to propagate to other peripherals and be able to enable/disable this. In the end I manage to create this function with a timer but this unfortunately generates something like 9 clock cycles of latency limiting the maximum frequency of the external clock signal. A basic Flip-Flop solution would probably introduce a much smaller latency.Competing products offer this kind of functionality more and more

Hello All,I am current testing STM32U375RGT6Q at 80 degrees and I see that there is significant increase in the average current consumption at 80 degrees C. Average Current consumption increases from 290uA to 1mA. Also note that1) Pull up and Pull down are 1Mega2) MCU is in sleep mode for 50 percent of the time.3) Internal oscillator MSI is used at 3MHz4) Flash memory is 1MB5) SMPS mode is used to reduce the current consumption.Is there a way out to reduce the current consumption at high temperature. I know that STM32L4 series are more stable over temperature but they dont suite the current budget of 300uA 

I would like to refer you to the following post from @JRuss.4 that was never satisfactorily answered:STM32L4 Standby Mode GPIO State {Schmitt Trigger} Clarification from Reference Manual I also have the exact same question.   Here is my version of the question boiled down to a couple of sentences:The STM32l4 series reference manual, RM0394 (Rev 5 - the latest available), on page 158, states, "In the Standby mode, the IO’s are by default in floating state. If the APC bit of PWR_CR3 register has been set, theI/Os can be configured either with a pull-up (refer to PWR_PUCRx registers (x=A,B,C,D,E,F,G,H)), or with a pull-down (refer to PWR_PDCRx registers (x=A,B,C,D,E,F,G,H)), or can be kept in analog state if none of the PWR_PUCRx or PWR_PDCRx register has been set."This is confusing.  The statement "In the Standby mode, the IO’s are by default in floating state" contradicts the statement, "or can be kept in analog state if none of the PWR_PUCRx or PWR_PDCRx r

I'm working on a device that requires requires 12 audio output channels and 10 input channels. I wish to do this over 16-slot TDM. Now, I'm concerned about whether this can be done with 32 bits per sample. The reference manual states in section 54.4.6 Frame synchronization "The audio frame length can be configured to up to 256 bit clock cycles". 256/16=16. Does this mean I can only do 16-bit audio with 16-slot TDM? Or did I misread.

I've STM32G474 using the HRTIMER to control a boost converter, each channel has it's own converter. This all works nicely with the deadtime, no issues. When I come to do a pulse skip, (set CMP3 to 0) the deadtime is still being inserted in the the Tx2 output even though Tx1 output is not being pulsed! Is this normal or have I missed something? I've tried a few things to not make the deadtime happen, like disabling the set and reset sources... the only thing that fixes the problem is to also set the falling deadtime to 0 and then subsequently resetting it back to the required value. Tx2 has no set or reset sources configured.

Hi,I would like to know where I can find the SPI controller version of the STM32G491.AN5543 lists features depending on the SPI controller version and says "To identify the version and the available feature set refer to the product reference manual and datasheet". However, I was not able to find this info in the RM or datasheet of the STM32G491 or anywhere else.

Hi, Does anyone know the default voltage level of an LPUART output as I am trying to interface with a device with a UART logic level of 1.8V so might need a level converter? Couldn't see anything about LPUART voltage on the datasheet? 

Hi,I have setup three channels in Timer_2 on an 32F429 MCU and have come across a seemingly inconsistent behaviour with regards to the alternate functions mentioned on the datasheet.More specifically, I have setup pins PA0, PA1, PA2 for Output_Compare, Input_Capture and PWM against channels 1, 2 and 3 of Timer_2 respectively and although the behaviour I observe on pins PA0 and PA1 is the expected one (well nearly the expected one but will ask a new question a bit later as that's probably a separate issue), pin PA2 is entirely dead as I don't get any pulsation happening whatsoever.I checked my configuration again and again in order to make sure it's setup correctly and verified the alternate functions I've setup for the gpio pins match the datasheet but that all looked fine:I then scrolled a bit further down on the datasheet and noticed that there's an alternative alternate-function pin for Timer_2 channel 3, namely PB10:So, I tried configuring that for the PWM pin and voila, it al

Hello,I want to generate four 50% duty cycle frequencies up to ~12kHz. It should be possible to enable/disable single outputs. Currently no special high requirements about accuracy, etc. Using a STM32U0 device (56MHz max).My first thought was to use an upcounting timer with four output compare channels where the timer itself is free running (ARR set to max. value). The compare channels are set to toggle on match and on each OC interrupt, the corresponding CCR register value is set to the next equivalent ARR value to toggle again. For example, if the timer is running at 1MHz and 1kHz frequency is needed, 1000 will be added to the CCR. To start/stop the output, I'd modify the corresponding OCxM value between toggle and frozen mode.However, I'm not sure if this is the most efficient way, especially regarding overhead and complexity. Another solution which came to my mind was to use a DDS approach with a (low power) timer, constantly firing interrupts at the needed resolution. On each