STM32CubeIDE (MCUs)

Hi Using FreeRTOS V11.0.1 and Stm32Cubeide 1.14.1 I was trying to read out the percentage information into the debugger.  Unfortunately I don't get the expected behaviorAs all of my tasks are either below 1% or at 1%, it does not seem correct.I have followed the instructions in stm32CubeIDE user guide and if I make a call to uxTaskGetSystemState from the FreeRTOS API, i can calculate values that make more sense as the IDLE task now takes up about 99% of the time under no load.Are there any other settings that needs to be fulfilled for this to work or are there any more needed configurations in FreeRTOS?Best regardsMartin

I have installed STM32Cubide v 1.16.1 on both linux as well as on windows machine. After installation i tried to create project creation. I select board which is (Nucleo F439ZI) then clicking on next finish --> it ask my for myST login --> Code generation pop up window came up and in tips asked me to do Project --> genrate code (Necessary firmware packages is misssing) once i click on ok project created with only .ioc file. Other file is missing.--> from help i tried Check for target selector then manage embedded software packages --> my STlogin again came up and Connection time out message even if my internet is working fine.--> is there any proxy related issse?--> uplaoding snapshot of mine network connection setting.--> also tired offline downloaded packages and upload form local still getting errror. (missing dependecy of packges)--> I tried with so many settings kindly help me to solve this issue.offiline installation from local drivenetwork connection s

Dear,used: STM32H7B0 mcu, 100pins          Segger j-link plus, v 9.4          STM32CubeIDE 1.16.1          GNU ARM 13.3.release 1STM32CubeIDE goes into a very long loop and/or crash. How to reproduce:- Create a large array, ex:  uint16_t buffer[0x8000]- start the code and add the "buffer" in "Live Expressions" - Open the "buffer" in " Live Expressions" and the IDE hangs.The only way we had found is to restart the IDE to get out.Has also try it with another compilers versions, but has the same issues.regards.

Recurring Error Message in STM32CubeIDE When Running or Debugging a Project. It shows- 'Launching pain Debug' Has encountered a problem.Error in final launch sequence:Failed to execute MI command: loadC:\\Users\\USER\\STM32CubelDE\\workspace_1.12.1\\pain\\ Debug\\pain.elfError message from debugger back end: Error finishing flash operation. and also it showing "Error in final launch sequence:Failed to execute MI command:load C:\\Users\\USER\\STM32CubeIDE\\workspace_1.12.1\\try\\Debug\\try.elf Error message from debugger back end:Error finishing flash operationFailed to execute MI command:load C:\\Users\\USER\\STM32CubeIDE\\workspace_1.12.1\\try\\Debug\\try.elf Error message from debugger back end:Error finishing flash operationFailed to execute MI command:load C:\\Users\\USER\\STM32CubeIDE\\workspace_1.12.1\\try\\Debug\\try.elf Error message from debugger back end:Error finishing flash operationError finishing flash operation"How to solve this problem? We are using STM32

Hi,i got quite some difficulties, having this run in a reliable way on a NUCLEO G431KBT6.It more often does not work, as it would work. It often just wouldnt print anything (But it had before, without issues!). Sometimes the swv debugger couldnt be enabled on debugger start, or the arm-none-eabi*.exe crashed. (i did not made a screenshot - foolish me).Anyone has some experience with this and could give me some tipps? Edit:The red record button behaves a little strange: It wont turn off sometimes, but when clicked, it wont turn on. But after having opened the settings, it is turned on.

Hai all,I am using ST Discovery Board (STM32f407) for SDIO based SD card interfacing and using Free RTOS.Here I already verified that SDIO with FatFs functions are working without Free RTOS.But whenever we enable free RTOS, that moment onwards FatFs getting hanged.Cannot able to open file or even not able to access the SD card properties.Here Stack is 128 and Heap is 26000.HCLK is 168 MHz.Please help me to solve this iussue.

I have tow arrays one named adcData[] that is adc input buffer and Xbuf[] that is output buffer. Now i am calculating some paramaters... But when i use my debuger and Live variables, i get only adcData[] and Xbuf[] is "Failed to evaluate expression". Arrays are declared same way and everything is configured similarly.

Hi,I created this Reset configThe address of Reset_Hnadler () is from a .map file.As the adress changes with builds, would be great to use function name.'set $pc=Reset_Handler'Is that possible ? What language is that 'set $pc ...' See chapter '3.1.5.6.2 Restart configurations' in 'UM2609 STM32CubeIDE user guide' (Eventually I'll port the handler from .s to .cpp and place it at a fixed address so that the address never change)Thanks

I just try using Nucleo L522ZE-Q and compile example codeafter i debug it, somehow it cannot write the file to the flashand the trace is not set properlyafter i downgrade the IDE using 1.14 it can work properly noplease fix the new IDE, i didn't want to use multiple version of cube IDE Thanks 

Hello.I am working on the LSM110A communications module project https://github.com/Support-SJI/LSM110A and I want to enable the necessary peripherals to be able to communicate the module with a MEMS using the SPI standard.The first thing I developed was the creation of a project, in STM32CubeIDE, in which I configured the SPI communication to the STM32WLE5CCU6 module. I created the code and used the source files (.c), which are included there, within the LSM110A project.Inside the “Drivers/STM32WLxx_HAL_Driver” folder of the LSM110A project, I created a file with the “link to file in file system” configuration and linked the source file “stm32wlxx_hal_spi.c”. Likewise, I performed the above procedure but with the “spi.c” file that is hosted in the “Application/User/Core” location; I also made sure that, in the folder containing the header files (.h), the “stm32wlxx_hal_spi.h” and “spi.h” files were included.My problem is that, when I made the linking of the “spi.c” file to the LSM

Good morning,I'm new to using the STM32. I have a Nucleo H755ZI-Q development kit.I need to write a command to SPI port type 0xfcd8000 or 0xfcb85b0 or 0x12000000. The max frame can be 32 bits.On the oscilloscope, I do have an SPI frame, but I always have an additional 0 bit at the end.I need to keep the value on the falling edge of the clock.When I write 0xfcd8000 (1111 1100 1101 1000 0000 0000 0000) , the SPI port writes 0x1F9B 0000 (0001 1111 1001 1011 0000 0000 0000 0000).It took me a while to configure it and I probably made a mistake. Could someone check my settings?Thank you in advance for your help. void SEND_COMMAND(uint32_t DATA) { /*SPI_DATA_SEND[0] = (DATA >> 24) & 0xFF; SPI_DATA_SEND[1] = (DATA >> 16) & 0xFF; SPI_DATA_SEND[2] = (DATA >> 8) & 0xFF; SPI_DATA_SEND[3] = DATA & 0xFF;*/ WAIT_BUSY(); HAL_GPIO_WritePin(GPIOB, CS1_AD5522_Pin, GPIO_PIN_RESET); /*HAL_SPI_Transmit(&hspi1, SPI_DATA_SEND, 4, 1000);*/ HAL_SPI_

..

Using STM32CubeIDE Version 1.14.1MCU Package STM32U5 1.4.0Using custom  STM32U5A9ZJT6Q  PCBIssue:-a.) if (HAL_GPIO_ReadPin(GPIOG, GPIO_PIN_7)) // PG7 pin 92 is always reading 0b.) HAL_GPIO_TogglePin(GPIOG, GPIO_PIN_12); // is not toggling the pinPorts A, C & E are working as expected.----------------------------------------------------------------------------------------------------------------I found possible issue and fixes in Zephyr rtos:-Zephyrproject-rtos / zephyr :- Drivers: gpio: stm32u5 portG not working #50158[backport v3.1-branch] drivers: gpio: stm32: Apply GPIOG specific code to U5 series #50484Question:Has the STM32U5 Port G issue been fixed on the STM32CubeIDE?If yes - how do I implement it?Please advise.

Hello, I would like to know How to configure the J-LINK Segger to work with STM32CubeIDE, after a little searching I found this video : https://www.youtube.com/watch?v=Rf-NKOoPYUc But at 12:11 I can see this configuration in the video              But I don't have an Application directory : In this case, do you have an idea how to do it ? Thank you for your helps. Regards

"I'm working with STM32 NUCLEOF429ZI but I encountered this error. Right after I plugged in the cable to upload the program, the txt file showed this error. Please help me identify the cause and how to fix it.""The interface firmware FAILED to reset/halt the target MCU"

I don't understand why there are no more .c and .h files but these in my project:What setting did I accidentally change? 

I am not able to use the UDP Server application(x-cube-subg2) for the extention board S2915A1. When I try to compile the generated code, I get the following compilation error. I had no trouble with running the P2P application from the same package, but this one doesn't seem to compile out-of-the-box for some reason.STM32Cube/Repository//Packs/STMicroelectronics/X-CUBE-SUBG2/5.0.0/Drivers/BSP/Components/S2LP/S2LP_Library/inc/S2LP_Csma.h:102:3: error: unknown type name 'SFunctionalState'STM32Cube/Repository//Packs/STMicroelectronics/X-CUBE-SUBG2/5.0.0/Drivers/BSP/Components/S2LP/S2LP_Library/inc/S2LP_Csma.h:154:15: error: unknown type name 'SFunctionalState'; did you mean 'FunctionalState'?(There are 73 errors similar to these ones)To give a little bit of context, the type "SFunctionalState" is declared in a file called S2LP_Types.c and the header file of the file is properly included inside the complaining file. From my perspective, the issue seems to be related to a circular dependency

Hello,I would like some guidance on how to setup the STM32CubeIDE to allow me to use C++23 on the ARM toolchain I usually use.The ARM toolchain is setup correctly but in the project's properties>C/C++ Build>MCU/MPU G++ Compiler>General, the language standard cannot go as high as iso or gnu C++20. Is there any way to write a value myself or do I have to use an external CMake.Thanks for your help,

 Memory regions were visible in STM32CubeIDE version 1.14.1. Later, I updated to STM32CubeIDE 1.16.1, and now the memory regions are no longer visible.Could you please assist me with this?  

Hi,I am receiving an error while I am debugging, I try to use the command in the message but the terminal doesn't recognize someone can help?   error prtscr

I have an issue here with the IDE. i have few projects compressed in .rar that I am using since the start of the year and everything worked well until this week. When i try to import one of these projects (any project) to my IDE, it shows me this window:And it always showed something like "Import Successfully"...I am using version 1.16.1 and i tried to downgrade to 1.14.0 because in other computer with this version still works.I have checked the .cproject and .project files but everything seems well... I am 99% sure that is anything about the IDE. Why it is happenning to me? How can i solve this issue?Thank you so much.

Hello,I am trying to open the generated code for my project. But when I try to open the code file that generated by CubeMX itself I get "not a valid ioc file" but if I try to open at diffrent IDE I can open. Also the file that generated is .eww file even though IDE insist on it is .ioc file. Can you help? Thanks.

In a project built using STM32F103, I have used TIM3 for some of my frequent tasks (like LED blinking and setting some flags etc.), which work perfectly. Today when I tried to enable ADC1 using DMA Circular, it looks like the TIM3 Global Interrupt handler is not invoked.. This line of code, stops the TIM3 interrupt.  HAL_ADC_Start_DMA(hadc, adcBuffer, 5) I don't find any relation between these 2. How ADC1 is related to TIM3? I am not using any channels of TIM3, just using its time elapsed event to do my tasks. Scratching my head.. Please help.   

Hi,I'm using STM32CubeIDE on latest Ubuntu:STM32CubeIDE Version: 1.14.1, Build: 20064_20240111_1413 (UTC).If I try to click "Import STM32Cube example", it shows next window with "target selection" which always fails (can only cancel, no selection possible, see below). Just in case, CubeMX works fine.Could anyone from ST comment if I miss something or it is a bug on Linux platform?

I had an issue, that i could not reproduce, because i could not restore the exact state of the project. The CubeIDE has its own version control for each file, which is of no great use, since the project consists of many files. Because of that i developed my own version control principle:Everytime a successful build happens, the files are committed to a certain branch of the repo. Then after an issue has been fixed, or i want to try out things / old states of a project, i use smartgit to handle those commits.Here is how to do it:1. Create a directory outside of the workspace and manually create backups (backups the git repo too)2. Setup git in the workspace (learn about git before - its quite a big topic)Exclude the ".metadata" directory (reinclude folders that should be version controlled - maven etc.)Create another branch for ongoing backups from the IDEAdd .gitignore file (see attached one - remove ".txt" to use it)3. Create script to commit changesto the specified branch (The p