STM32CubeIDE (MCUs)

For example:   Surely, those are read references - not write? PS:The question arose here.

Hello.For now only Ctrl + Shift + "+" and Ctrl + "-" are worksImpossible to do sorter way Ctrl + "+", and Ctrl + "-" on Num pad :(In the Mac OS(latest on M1) Command + "+"  or Command + Shift + "+" do not works at all.Possible to zoom in only via menu, "Window" -> "Editor" -> "Zoom in" :(Thank U

Dear all, when I press Install button in the Toolchain Manager of the 1.17.0 CubeIDE it hangs after opening the subsequent dialog. I cannot close this dialog with neither mouse nor ESC key, need to terminate the task.  Regards,Dmitry

Kiel uvision has this feature where they show the pdf of relevant documentations when you select board and chip while creating a project. Does stm32cubeide have a similar feature somewhere so i can look for the stm i am using.also i found it hard to find the same pdf on google for some reason, like i had to type specific phrases from the document in order to find itabove is photo with pdfs on the right

Hello! I am developing my first FreeRTOS system and believe I have an error somewhere between tasks and I cannot find a good way to monitor them as the debugger is not showing me that multiple threads are running but as I step through it jumps from task to task when they are blocked so they should be preempting.  Anyways, I am using the STM32F446RE Nucleo development board with the folowing firmware versions: ST-Link V2J4M32 STM Debug+Mass storage+VCP STM32CubeIDE 1.16.1 Here is the setup for my tasks  /* definition and creation of NoteQueue1 */ osMessageQDef(NoteQueue1, 64, note); NoteQueue1Handle = osMessageCreate(osMessageQ(NoteQueue1), NULL); /* Create the thread(s) */ /* definition and creation of ParseMidi */ osThreadDef(ParseMidi, StartParseMidi, osPriorityNormal, 0, 128); ParseMidiHandle = osThreadCreate(osThread(ParseMidi), (void*) ctrl); /* definition and creation of AudioOutput */ osThreadDef(AudioOutput, StartAudioOutput, osPriorityNo

Hello  ST Community,I'm experiencing an issue with my STM32 development setup in STM32CubeIDE. When I try to connect to my target device [ STM32WLE5JC Module(LoRa-E5 mini)] using the ST-LINK, I receive the following error:"Target no device found, Error in initializing ST-LINK device.Reason: No device found on target."My Setup:----------------------------IDE: STM32CubeIDEST-LINK SN : 260023000B33353739303541ST-LINK FW : V2J45S7MCU: STM32WLE5JC(LoRa-E5 mini) Steps Taken:----------------------------- Verified physical connections.- Powered the microcontroller adequately.- Used ST-Link utility and CubeIDE for debugging.- Configured the software environment for SWD. I'm reaching out to the community for insights into resolving the connectivity issue. If anyone has encountered similar problems or has expertise in debugging STM32 microcontrollers, your input would be highly appreciated.  

Hello,I am trying to learn a structure that is provided for MVP implementation. I dont understand where is Screen1View and every other class instance placed. I see that definitions are in .hpp files and implementations of .cpp file. Also, I am really curious where is the Screen1Presenter(Screen1View& v) function called.  #ifndef SCREEN1PRESENTER_HPP #define SCREEN1PRESENTER_HPP #include <gui/model/ModelListener.hpp> #include <mvp/Presenter.hpp> using namespace touchgfx; class Screen1View; class Screen1Presenter : public touchgfx::Presenter, public ModelListener { public: Screen1Presenter(Screen1View& v); /** * The activate function is called automatically when this screen is "switched in" * (ie. made active). Initialization logic can be placed here. */ virtual void activate(); /** * The deactivate function is called automatically when this screen is "switched out" * (ie. made inactive). Teardown functionality can be placed here. */ vi

I am working with stm32h745ZIT3, in my application I need to receive some packets over ethernet in CM7 and these packets need to share to CM4, and processing is done in CM4. So, to test this data transfer I need to debug both cores simultaneously. Tried changing the debug properties as download option disabled for cm4 and add cm4 to cm7s list. and then tried to debug cm7 and then debug cm4, but cm4 shows as no ST detected. Also, port number changed for both. Is there anything I am missing? please guide me. Power: LDO 

Hi ST Community, I am using the board of STM32WBA55CGU6 board for OTA application and i want to use the application present in STM32Cube_FW_WBA_V1.3.0 and STM32Cube_FW_WBA_V1.2.0 packages. Since these packages are present in STM32Cube IDE version 1.15.0 and STM32Cube IDE version 1.14.0 respectively and is not available in the community for installation, i request to send the respective files to the mail id :- " shivaparbati2001@gmail.com " Thank You.

Hello all.I'm new here, this is my first post.I found a problem with STM32CubeIDE.I don't know where to post errors report, so please move this post if this is the wrong place.I'm a skilled embedded programmer, but I've worked till now on 8 bit microcontroller (AVR, PIC, STM8, Z80, etc.).Now we (me and my company) are moving to the ARM platform, and I choose STM32 as our next family of MCU/MPU.We need two different platform, for different devices: an high performance one, for which I choose the Cortex-M33 (STM32H5 family) and a low power, low cost one, for which I choose instead the STM32C0+ (STM32C071).I bought few NUCLEO boards, so I can learn the new ecosystem in an easy way.I installed STM32CubeIDE, complete with CubeMX.I created a new STM32 project, using the board selector I choose the NUCLEO-H563ZI board.Using CubeMX I configured the board; I also enabled BSP HMI code generation, and enabled User Leds.I decided to use ThreadX and NetXDuo.Now, there's a little problem: When I cre

I saw a post from 2020, which said NO to raspberry pi, but that was before Apple's and Microsoft's latest machines started supporting ARMv7 architecture.Per the "STM32CubeIDE installation guide", section 1, states the following:Only 64-bit OS versions are supportedSTM32CubeIDE supports STM32 32-bit products based on the Arm® Cortex® processorFrom this, it appears that ST is telling us that Raspberry Pi is supported.  I think ST should immediately update the instruction guide to fix the 32/64 bit contradiction, and it would be ideal to make a clear statement that ARMv7 is only supported for Apple and Microsoft OSs.For another reason, I expect the instructions are wrong.  When I attempt to install the debian version on my Pi, it tells me what packages are missing.  Each one listed includes amd64 for architecture. The following packages have unmet dependencies: st-stlink-server:amd64 : Depends: libusb-1.0-0:amd64 but it is not installable st-stm32cubeide-1.17.0:amd64

IDE: STM32CubeIDE 1.17.0Board: NUCLEO-H7S3L8OS: Kubuntu 24.04 / Windows 10 I imported different example projects, but when I want to debug the project, I get this error"Failed to execute MI command:load /home/[User]/STM32CubeIDE/workspace_1.17.0/[Example]/STM32CubeIDE/Appli/Debug/[Example]_Appli.elf"(complete output below)I tried Linux Kubuntu 24.04 and Windows 10 (VirtualBox), the on board ST-Link v3 (JP1 open) and external ST-Link v3 (JP1 set). Then I created a new Project without any user code and it works.Next I tried an example project for NUCLEO-F446ZE (on board ST-Link v2-1) and it works fine, too. In addition, the example Project "LwIP_HTTP_Server_Raw" for H7S3L8 even caanot be imported. After pressing "Finish" the windows remains open with the error message "Fail to perform local copy" on top. With "Cancel", the example is not listed in the prject explorer, but is present on the file system (workspace). After this, the folder from the workspace can be impor

Hi,In How to enable FreeRTOS™ Run Time and Stack Usage view, it shows we can see the task runtime usage in percentage for FreeRTOS. But for ThreadX, it has no such item.  As there is an 'execution_profile_kit' utility tool in ThreadX already, any plan to add this feature for ThreadX?Thanks.

i have an example code which reads the adc value in continuous conversion mode with dma. I have done all the  initialization part but its doesn't work for contionus conversion which shows some random values for adc.But it do work for single conversion. The only changes made is  i have disabled the continuous for single conversion.AdcHandle.Instance = ADCx; AdcHandle.Init.ClockPrescaler = ADC_CLOCKPRESCALER_PCLK_DIV2;AdcHandle.Init.Resolution = ADC_RESOLUTION_12B;AdcHandle.Init.ScanConvMode = DISABLE;AdcHandle.Init.ContinuousConvMode = DISABLE;AdcHandle.Init.DiscontinuousConvMode = DISABLE;AdcHandle.Init.NbrOfDiscConversion = 0;AdcHandle.Init.ExternalTrigConvEdge = ADC_EXTERNALTRIGCONVEDGE_NONE;AdcHandle.Init.ExternalTrigConv = ADC_EXTERNALTRIGCONV_T1_CC1;AdcHandle.Init.DataAlign = ADC_DATAALIGN_RIGHT;AdcHandle.Init.NbrOfConversion = 1;AdcHandle.Init.DMAContinuousRequests = ENABLE;AdcHandle.Init.EOCSelection = DISABLE; if(HAL_ADC_Init(&AdcHandle) != HAL_OK){/* In

Hi guysThis project here was built and debugged fine last week. Today, I get this message:'Launching has encounteres a problem. Error in final launch sequence: Failed to execute MI command: -environment-cd <Path/to/project> Error message from debugger back end: <Path/to/project>Here is the whole console output: STMicroelectronics ST-LINK GDB server. Version 7.8.0 Copyright (c) 2024, STMicroelectronics. All rights reserved. Starting server with the following options: Persistent Mode : Disabled Logging Level : 1 Listen Port Number : 61234 Status Refresh Delay : 15s Verbose Mode : Disabled SWD Debug : Enabled InitWhile : Enabled Waiting for debugger connection... Shutting down... Exit. There are a lot posts with "Failed to execute MI command" problems here, but I did not find mine. I hope, somebody knows how to fix that. As I said, running and debuging the project worked nice some days ago, and I do not see reason why it does not continue its fluent work

Moved from the MPUs section, as this is MCU-related. Subject: Feedback and Request for Clear Documentation for the Nucleo-F767ZI Board and Associated Tools   I am writing to express my frustration and disappointment with the current state of support and documentation for the Nucleo-F767ZI board. As a customer who has invested in your product, I expected a streamlined experience and effective tools to get started. Unfortunately, that has not been the case. On-Board Programming and Firmware Update:While the on-board programming feature partially worked in updating the firmware, that’s as far as it went. Beyond this, the tools provided fail to offer a clear and functional path for utilizing the board effectively. Eclipse IDE and Software Environment:The Eclipse-based IDE is overly complex and riddled with unnecessary layers, which hinder rather than help the development process. Instead of a user-friendly experience, the IDE feels like a maze of rat holes, offering no clear path

Hi,i never had to much trouble with errors while debugging. But its getting exessive.It only happens, when i debug a session, after i had already debugged a session. It makes no difference, if i manually terminate the last session before. I already tried different reset methods, which seemed to have no effect either.It only applies to starting the debug session with the "bug" button (which would include the rebuild).Sometimes i have to restart the IDE to make it work again. I never had such problems before, and i did not really change much with the settings.This issue is not present, when using a Nucleo board, but there is another issue (hard fault on debug only). I am using this: https://www.st.com/en/development-tools/stlink-v3mods.htmlBought from reichelt.de

hi im using stm32g474vet6 mcu, i want generate centrealigned mode pwm of 5khzhow to generate 5khz pwm in centre aligned mode, how to calculate the ARR value for 5khz, since my timer1 clk is 170mhz im not doing any prescalar.can some share the formula for calculating period value and frequency in center aligned mode.

There is a bug in the new cube ide version in the lwip vonfiguration for the STM32F7 LWIP_RAM_HEAP_POINTER (RAM Heap Pointer) 0x30004000There is no such RAM location in the STM32F7. the correct value should be zero but better u guys check it. by the way this option was not there for the F7 LWIP Key options settings in the previous cube ide version. 

I am working on the blink led project on the Nucleo - F103RB, I facing error during the code generation process, the code isn't generating. Might be something with macbook, that i need to install any extra packages or something.Can someone plzz help me with this :folded_hands:.

I found a different behavior, with or without optimization, that I can't explain me.In the code snippet  below, the value b is 0 if you compile without optimization and 1 with optimization enabled (-O1) (gcc ver 12.3.rev1).The only apparent difference is having defined zzz3 as volatile.I obtained this behavior on both F3 and F4 microprocessors. The same code instead works correctly on other architectures both arm and x86, so the result is 0 both for a and b.Is it a wrong behavior or is it part of an unpredictable behavior that can be overcome by forcing memory barrier or something else? {static long zzz;static long zzz2;static volatile long zzz3;static int a, b; zzz = 0x80000000-10;zzz2 = zzz + 1000;zzz3 = zzz2; a = (zzz - zzz2) > (-1L);b = (zzz - zzz3) > (-1L); printf("1=failed : a=%d b=%d\n", a, b);} thanks, for help

My main computer died and I tried to install STM32CubeIDE on a spare computer. During the installation process I received the following error message:"NSIS ErrorError launching installer"Computer: Firebat Mimi PC, Model S1, CPU Intel N100, RAM 16GB. Operating system: windows11.I tried installing different versions of CubeIde: 1.17.0, 1.16.1, 1.15.1. The result is always the same.Note: STM32CubeMx has installed successfully and is working.Is it possible to somehow solve this problem?   

Hi All,  I am trying to import the X-CUBE-SPN2 in CubeIDE, I have followed all the correct steps and am importing the project through the filesystem. However, when I try to build the project I constantly keep getting an error stating that: An internal error occurred during: "Build Project".java.lang.NullPointerException.Please find the attached

I have a problem with not being able to start a trace to plot a global variable with my STM32F3DiscoveryKit. The global variable is changing the red Button is greyes out. Of corse the SWV is enabled in debugging. It might have something to do with a pin conflict but I am really not sure. Does someone have an Idea on how to solve this issue?   Thank you in advance!  

In the above examples the .ioc file is missing. Usually when am unable to open the ioc file, I'll try to open the same ioc file in cube mx and generate the code for stm32 cube ide or I'll update the version of cube ide to migrate to the newer versions. But in above such cases, I don't know how to utilize such libraries. Kindly help me regarding the same.! Thanking you